STIEBEL ELTRON AWG 315 SR User manual

INSTALLATION
INSTALLAZIONE
Wanddurchführung | Wall outlet | Traversée murale | Passaggio nella parete | Væggennemføring
» AWG315GL
» AWG315SR
» AWG315L
» AWG560H-GL
» AWG560H-SR
» AWG560V-GL
» AWG560V-SR
» AWG560L
» AWG600L

8| AWG 315-600
INSTALLATION
General information
1. General information
This document is for contractors.
Note Read these instructions carefully before using the ap-
pliance and retain them for future reference.
Pass on the instructions to a new user if required.
 This symbol indicates that you have to do something. The
action you need to take is described step by step.
1.1 Relevant product
This document describes the installation of the following wall
outlets:
Wall outlet Part number
AWG 315 L 231039
AWG 560 L 231041
AWG 600 L 231044
AWG 315 GL 232955
AWG 560 H-GL 232956
AWG 560 V-GL 232957
AWG 315 SR 233836
AWG 560 H-SR 233837
AWG 560 V-SR 233838
1.2 Further applicable documents
Operating and installation instructions of the heat
pump or air conditioning unit
1.3 Units of measurement
Note All measurements are given in mm unless stated oth-
erwise.
2. Safety
Only qualied contractors should carry out installation, com-
missioning as well as maintenance and repair of the product.
WARNING Injury The discharged cold air can cause condensation to
be formed in the vicinity of the air outlet.
 Ensure that no risk of slipping due to ice forma-
tion occurs on adjacent footpaths and drive-
ways during low temperatures.
!CAUTION Injury
This product has sharp edges which can cause cuts
unless handled with care.
 Take care when handling objects with sharp
edges and wear protective equipment including
gloves.
Note Observe all applicable national and regional regula-
tions and instructions.
3. Product description
This product is used as a wall outlet for the outside air or dis-
charge air duct from heat pumps or air conditioning units.
Products AWG L are intended for installation in cellar ducts.
The product can be used in wall knock-outs with any wall con-
struction.
The product features a weather grille. Behind this is a ne
meshed grille designed to prevent animals getting in.
3.1 Standard delivery
AWG 315 GL / AWG 315 SR
26_03_14_0074
1
23
4
5
1 Weather grille
2 Insert
3 Wall outlet
4 Hose clip with tensioning closure
5 Insulating mat
AWG 560 H-GL / AWG 560 H-SR
26_03_14_0075
1234
1 Weather grille
2 Insert
3 Wall outlet
4 Hose clip with tensioning closure

AWG 315-600 | 9
ENGLISH
INSTALLATION
Mounting
AWG 560 V-GL / AWG 560 V-SR
D0000058931
1234
1 Weather grille
2 Insert
3 Wall outlet
4 Hose clip with tensioning closure
AWG 315 L
26_03_14_0074
1
23
4
5
1 Grille to keep out small animals
2 Insert
3 Wall outlet
4 Hose clip with tensioning closure
5 Insulating mat
AWG 560 L
26_03_14_0109
1234
1 Grille to keep out small animals
2 Insert
3 Wall outlet
4 Hose clip with tensioning closure
AWG 600 L
D0000058932
1
23
4
1 Grille to keep out small animals
2 Insert
3 Wall outlet
4 Hose clip with tensioning closure
Also part of the standard delivery:
-Four self-tapping screws (4.2x32) to connect the insert
and wall outlet
-Four screws (M5x10) for securing the weather grille to the
insert
-Installation aid:
Two sections for AWG 315 GL, AWG315SR, AWG315L
and AWG 600 L; three sections for AWG 560 H-GL,
AWG560H-SR, AWG560V-GL, AWG560V-SR and
AWG560L
-Thermal insulation tape
-Protective cover (tted in the wall outlet)
-Two anti-drip caps (not for the AWGL)
3.2 Accessories
-Air deector
4. Mounting
!Damage to the appliance and environment
The weather grille is tted with a drip edge to prevent
condensate running down the building envelope and
damaging the building. A prerequisite for this is that
the building envelope is vertical.
With the L versions, the drip edge is at the top and
serves to prevent water running down the wall from
reaching the wall outlet.
4.1 Installation location (only for AWG L)
Observe the minimum size of the cellar duct to enable an un-
restricted air ow (see "Specication/ Minimum dimensions
of the cellar duct").
Note When sizing the cellar duct, please note that the insert
and weather grille have to be tted from the outside.

10 | AWG 315-600
INSTALLATION
Mounting
4.2 Fitting the wall outlet
 Make an opening in the wall (see "Specication")
AWG 315 GL / AWG315SR / AWG 315L / AWG600L
26_03_14_0078
AWG560H-GL / AWG560H-SR / AWG560V-GL/
AWG560V-SR / AWG560L
26_03_14_0079
Push the parts of the installation aid together at the cut-out
points.
 Position the installation aid in the wall outlet.
The installation aid stops the wall outlet becoming deformed
as you carry out the next steps.
 Insert the wall outlet into the opening in the wall.
The oval connector, or round connector for AWG 315 and 600,
must be facing the inner surface of the building. We recom-
mend installing the wall outlet in such a way that it is posi-
tioned ush with the inner surface of the building.
 Seal the space between the wall and wall outlet, e.g. using
a foam sealant.
 Once the seal is complete, e.g. when the foam sealant has
hardened, remove the installation aid from the wall outlet.
Note Carry out the following steps once the outer wall of
the building is complete, after the external rendering
or brickwork has been applied to the house.
D0000036429
4.3 Trimming the insulation
Depending on the thickness of the building envelope, the in-
sulation mats pretted in the wall outlet may need trimming.
50
26_03_14_0070
 Trim the insulation mats until they end 50mm within the
outside edge of the wall.
4.4 Fitting the insert
 Push the insert into the wall outlet. The insert is designed
in such a way that part of the insulation mat is pressed
outwards, which seals the wall outlet.
4.4.1 AWG 315 GL / AWG 315 SR / AWG 315 L: Axing the
insulating mat
D0000058225
3
2
1
1 Rear of the wall outlet
2 Insulating mat which must be axed to the oor of the
wall outlet
3 Insulating mat in the insert, axed at factory
Insulating mats are axed to the four walls of the insert at the
factory. The insulating mat included in the standard delivery
must be axed behind the insert, to the oor of the wall outlet.
 Measure the depth of insulation required from the rear of
the wall outlet to the edge of the insulating mat axed to
the insert.

AWG 315-600 |11
ENGLISH
INSTALLATION
Mounting
 If necessary, trim the supplied insulating mat to the meas-
ured depth.
 Pull the insert out of the wall outlet.
 Pull o the foil from the self-adhesive side of the insulat-
ing mat.
 Ax the insulating mat to the oor of the wall outlet.
 Seal the gaps around the insulating mat, e.g. with silicone.
 Push the insert back into the wall outlet.
 Seal the gap between the insert and the axed insulating
mat, e.g. with silicone.
4.4.2 Securing the insert
AWG 315 GL / AWG 315 SR / AWG560H-GL/
AWG560H-SR / AWG 560V-GL / AWG560V-SR
26_03_14_0094_
1
3
2
AWG 315 L / AWG 560 L / AWG 600 L
26_03_14_0094_
1
3
2
1 Screw 4.2x32
2 Screw M5x10
3 Washer/disc
The insert has eight position markers.
 Screw the self-tapping screws (4.2x32) provided into the
four positions marked in the side panels, in order to con-
nect the insert to the wall outlet.
4.5 Fitting the weather grille
 Remove the protective cover that covers the opening to
the connectors inside the wall outlet.
 Secure the weather grille in the holes in the insert using
the screws provided (M5x10). Ensure that the drip edge
of the weather grille is facing downwards.
Fit anti-drip caps (not for the AWG L)
26_03_14_0140
1
1 Anti-drip caps
 On the l.h. and r.h. ends of the drip edge, ax the anti-
drip caps supplied, possibly using silicone as an adhesive.
Sealing the weather grille all around
 Seal the gap between the building wall and weather grille,
e.g. using silicone.
4.6 Connecting the air hose
 AWG 560 H-GL, AWG560H-SR, AWG560V-GL,
AWG560V-SR, AWG560L: Adapt the shape of the hose to
match the oval wall outlet connector.
 The hose clip closure is pre-tted to the hose clip band.
 Push the free end of the hose clip band into the hose clip
closure.
2 3
D0000060901
1
1 Hose clamp
2 Internal hose
3 External hose
 Slightly pull back the external hose and the thermal insu-
lation, so that the internal hose of the air hose protrudes
a little.
 Invert the internal hose halfway down the connector.
D0000060902