Stiga Play The Best T8725W/F User manual

1. Read this manual carefully before starting assembly. Read each step completely before beginning
each step.
2. Some smaller parts may be shipped inside larger parts. Check inside all parts and cartons before
assembling or ordering parts.
3. If hardware is tightened too soon, mounting holes may not align and parts may not easily fit together.
Leave bolts slightly loose until you are instructed to tighten them.
4. To make assembly as easy as possible, place all parts of the table tennis in a cleared area and
remove the packaging material. Organize all parts as per parts identifier in the assembly manual.
Do not dispose of the packing material until assembly is completed.
5. Avoid scratching table tennis top and metal tube parts during the assembly process.
6. Assemble product on clean, level and flat surface.
7. Take time to correctly orientate parts exactly as per each assembly diagram.
8. Save this instruction in the event that the manufacturer has to be contacted for replacement parts.
O W N E R ’ S M A N U A L
Please visit our website at: www.escaladesports.com
ON-LINE TROUBLE SHOOTING TECHNICAL ASSISTANCE
ON-LINE PARTS REQUESTS FREQUENTLY ASKED QUESTIONS
ADDITIONAL ESCALADE SPORTS PRODUCT INFORMANTION
R
Escalade Sport products may be manufactured and/or licensed under the following patents.
6120397 , 5816957 , 5769744 , 5119741 , 4911085 , 4717157 , D460140 , D420563
Additional patents may be pending. One or more of the listed patents and/or pending patents may cover specific product. 2021 Escalade Sports
R
C
R
Please Do Not Return This Product To The Store!
Contact Escalade Sports customer service department at:
R
READ ASSEMBLY, OPERATING AND SAFETY INSTRUCTIONS
CAREFULLY! AT LEAST TWO ADULTS ARE NEEDED TO PUT
THIS TABLE TOGETHER!
Thank you for buying our product. We try hard to ensure that our products are of high quality and free of problems, such as
Manufacturing defects or missing parts. However, if you have any problems with your new product, please DO NOT RETURN IT
TO THE STORE!
Be sure to write your model number and serial number here
for future reference. You can find these numbers printed on
the bottom of the table.
MODEL NO.: T8725W/F
DATE CODE : CPSIA#2-T8725W/F-_______-SY
PURCHASE DATE : _______________________
Please provide model number and/or part number of the product and/or part when you call or write. These numbers can be found on the
product, packaging, and/or in this Owner’s Manual.
CAUTION:
Phone: [phone] Toll-Free!
Fax: [phone] Toll-Free!
E-mail: [e-mail]
Mailing Address
(correspondence only):
Escalade Sports
PO Box 889, Evansville, IN 47706
Physical Location:
Escalade Sports
817 Maxwell Ave.
Evansville, IN 47711

- 2 -
CARE AND MAINTENANCE
You have purchased a quality product that will give you years of enjoyment. By following these simple
maintenance steps, you will add to the life of your new table.
The top (playing surface) of your table is made of Particle Board. Like all products made of wood, it
can be affected by atmospheric changes in both temperature and humidity. This may cause a slight
sag or distortion as the top expands or contracts. This is normal and should not cause concern as it
does not detract from the play or utility value of the table. After assembly of the table, you can minimize
the effects of temperature and humidity changes by storing the table in a dry area when table is not
in use.
This table must be stored indoors to prevent damage to the playing surface. Dampness and extreme
temperature changes can cause the wood to warp, swell, crack or blister. When your table is not in
use, it should be stored in a dry area. Due to the nature of particle board, table top may bow.
Damp and humid conditions will amplify this. This is normal and will not affect playability of table.
THE TABLE TOP
STORAGE OF YOUR TABLE
To clean your table use a soft, damp (NOT WET) cloth only. To prevent damage to your table’s playing
surface, DO NOT USE ANY CHEMICALS, ABRASIVE OR CLEANING PRODUCTS on your table’s playing
surface.
CLEANING YOUR TABLE
Be sure to oil all moving parts of your table including the pivot points. This will insure the safety and ease
of use of your table.
MAINTENANCE OF YOUR TABLE
If table does not seem level, it is probably due to uneven or unlevel floors. Set the table in its PLAYING
POSITION and move table several inches in different directions to find the best location for the table.
If the floor is extremely unlevel, table may not play or operate properly.
If table is high in the center, shim up under the outer legs.
UNLEVEL FLOORS
This table must be kept indoors to prevent damage to the playing surface. Dampness and extreme
temperature changes which occur on patios or similar areas can cause wood to warp, swell, crack or
blister.
It is recommended to keep the carton for folded table storage and or transport.
Also, note when folded, the table has casters on the bottom side to make movement easier.
When transporting the folded half tops, be careful not to damage the lower corners or scratch the playing
surfaces.
TRANSPORTING THE FOLDED TABLE TOPS

- 3 -
HARDWARE IDENTIFIER (To Scale)
- Lower “A”Leg
Connector
(8 pcs)
Pre-installed
PARTS IDENTIFIER (Not to Scale)
P1- Table Tennis Table Top
and Frame Assembly
(2 pcs)
P2 - Leg With Leg Caps
(4 pcs)
Pre-installed
P3 P4 - Lower “B”Leg
Connector
(8 pcs)
Pre-installed
P6- Net Post
P5 - Upper Leg Connector
(2 pcs)(4 pcs)
P7 - Net (1 pc)
H1 - 8 mm x 40 mm
Tensioning Knob Bolt - Short
(4 pcs)
H2 - 8 mm x 55 mm
Knob Bolt - Long
(8 pcs)

P2
P2
- 4 -
PARTS REQUIRED
1 pc P1 Table Tennis Table Top and Frame Assembly
STEP 1:
IMPORTANT NOTE: Place table half top with playing surface face down on a CLEAN flat surface
for ease of correct assembly and to prevent any scratches or blemishes to the playing surface.
-
Lay one piece P1 Table Tennis Table Top and Frame Assembly flat with playing surface
facing down as shown in FIGURE 1.
Unlock the SAFETY LOCK as shown in DETAIL A .
STEP 2:
Carefully Pull open the P2 Legs and slightly
push it down as shown in FIGURE 2.
FIGURE 2
s
!WARNING
Crush and Shear Points
Keep hands clear of hinge
area and Aprons when
unfolding table top.
!WARNING
Crush and Shear Points
Keep hands clear of hinge
area and Aprons when
unfolding table top.
P1
FIGURE 1
DETAIL BDETAIL A
Safety Lock
Carefully lift and fold open the table half.
Slightly
push down
Slightly
push down
Pinch Points
Keep hands clear of
the leg pivot area when
folding the table leg.
Pinch Points
Keep hands clear of
the leg pivot area when
folding the table leg.

- 5 -
PARTS REQUIRED
4 pcs P5 Upper Leg Connector
8 pcs - H2 Knob Bolt - Long
-
Install P5 Upper Leg Connector with P3 Lower “A”Leg Connector and P4 Lower “B”Leg Connector using H2 Knob Bolt - Long
as shown in FIGURE 3 & DETAIL B,C,D,E. Tighten this hardware. DO NOT OVERTIGHTEN AND CRUSH TUBES.
Repeat procedures for other table top.
STEP 3:
P5
P5
P5
FIGURE 3
DETAIL BDETAIL B
DETAIL BDETAIL C
H2
H2
P4
P4
P3
P5
P3
P3
P4
NOTED:
Both P3 and P4 are pre-installed
H2
P3
P4
P4
DETAIL BDETAIL D
P5
DETAIL BDETAIL E
H2
P3
P5

4 pcs - H1
- 6 -
Attach one P6 Net Post to the middle edge of where the table halves meet.
Repeat this with other P6 Net Post on opposite side.
STEP 4:
PARTS REQUIRED
2 pcs - P6 Net Post
1 pc - P7 Net
4 pcs - H1 Tensioning Knob Bolt – Short
2 pcs - P6 Net Post
1 pc - P7 Net
Then, slide P7 Net into corresponding P6 Net Post and repeat for the other side as shown in DETAIL F.
Install H1 Tensioning Knob Bolt - Short,
in one end of each P5 Upper Leg Connector as shown in DETAIL G.
Snug Tighten these 4 pcs of H1 Tensioning Knob Bolt - Short.
!WARNING
THIS STEP REQUIRES TWO CAPABLE ADULTS.
VERY CAREFULLY TURN THE TABLE OVER AND SET IT
ON ITS LEGS. BE CAREFUL THE TABLE IS HEAVY .
DROPPING THE TABLE CAN CAUSE SERIOUS INJURIES
OR PROPERTY DAMAGES.
TOP VIEW
P7
P6
P7
P6
P6
FIGURE 4
NOTED: H1
DETAIL BDETAIL F
P5
DETAIL BDETAIL G
P5
H1
Do not overtighten.
Install and snug tighten H1
on other end of P5.
P5
H1
H1
H1

P7
P6
P6
H1
- 7 -
CAUTION:
READ OPERATING INSTRUCTIONS CAREFULLY BEFORE OPERATING TABLE! DO
NOT ALLOW CHILDREN TO OPEN TABLE! DO NOT CLIMB, STAND OR JUMP ON
TABLE! SERIOUS OR FATAL INJURY MAY RESULT! THIS IS NOT A TOY! TABLE IS
TO BE OPENED OR CLOSED BY ADULTS ONLY! FAILURE TO COMPLY WITH
OPENING AND CLOSING INSTRUCTIONS COULD RESULT IN PERSONAL INJURY OR
PROPERTY DAMAGE.
STORAGE OF THE TABLE:
STEP 1:
STEP 3:
Fold each Leg and half table as shown in FIGURE 7. STEP 4:
Lock the table using SAFETY LOCK as shown in FIGURE 8.
STEP 5:
Repeat procedure for other table top.
STEP 2:
FIGURE 5
FIGURE 6
FIGURE 7
FIGURE 8
Remove the P7 Net and P6 Net Posts as shown in
FIGURE 5.
H2
H2
Remove H1 Tensioning Knob Bolt - Short, and H2
Knob Bolts - Long, as shown in FIGURE 6.
H2 H2
H1

C5
C5
C5
C6
C6
C8
C2
C5
C6
C7
P3
P4
C5
C3
C8
P2
P1 P5
C4
C17
C18
C18
C19
DETAIL H
DETAIL G
DETAIL E
DETAIL D
DETAIL C
DETAIL B
C15
C10
C10
C10
C11
- 8 -
H1
C8
C1
C9
C14
C12
C13
C16
C10
DETAIL A
H2
DETAIL F

- 9 -
T8725 TABLE TENNIS TABLE SPARE PARTS
Key#
Part No. Description Qty
H1 T8725SY-H1 8 mm x 40 mm Tensioning Knob Bolt - Short 4
H2 T8725SY-H2 gnoL-tloBbonKmm55xmm8 8
P1 T8725SY-P1 ylbmessAemarFdnapoTelbaTsinneTelbaT 2
P2 T8725SY-P2 )dellatsni-erP(spaCgeLhtiWgeL 4
P3 T8725SY-P3 )dellatsni-erP(rotcennoCgeL”A“rewoL 8
P4 T8725SY-P4 Lower “B”Leg Connector (Pre-installed)
Net Post
8
P5 T8725SY-P5 Upper Leg Connector
Net
4
P6 T8725SY-P6 2
P7 T8725SY-P7 1
DETAIL A
C2 T8725SY-C2 8
C5 T8725SY-C5 16
C6 T8725SY-C6 8
C7 T8725SY-C7
8 mm x 75 mm Allen Head Bolt
8 mm x 22 mm Flat Washer
8 mm Nylon Lock Nut
8 mm x 18 mm Plastic Bushing 8
DETAIL B
C3
C5
T8725SY-C3 8 mm x 50 tloBdaeHnellAmm 8
T8725SY-C5 8 mm x 22 mm Flat Washer 8
C6 T8725SY-C6 8mm Nylon Lock Nut 8
C8 T8725SY-C8 8 mm x 16 mm Plastic Step Bushing 16
DETAIL C
C4 T8725SY-C4 8 mm x 35 mm Allen Head Bolt 8
C5 T8725SY-C5 8 mm x 22 mm Flat Washer 16
C6 T8725SY-C6 8mm Nylon Lock Nut 8
C10 T8725SY-C10 3.5 mm x 14 mm Round Head Screw 32
C14 T8725SY-C14 Plasitc Bracket 8
DETAIL D
C10 T8725SY-C10 wercSdaeHdnuoRmm41xmm5.3 16
C11 T8725SY-C11 Plasitc Leg Cap 8
DETAIL E
C9 T8725SY-C9 3.5 mm x 12 mm Round Head Screw 8
C16 T8725SY-C16 Safety Lock 2
DETAIL F
H1 T8725SY-H1 8 mm x 40 mm Tensioning Knob Bolt - Short 4
H2 T8725SY-H2 8 mm x 55 mm Knob Bolt - Long 8
C8 T8725SY-C8 8 mm x 16mm Plastic Step Bushing 8

- 10 -
T8485 TABLE TENNIS TABLE SPARE PARTS
Key# Part No.
Description Qty
DETAIL H
C17 T8725SY-C17 6mm x 55 mm Allen Head Bolt 8
C18 T8725SY-C18 6mm x 18mm Plastic Flat Washer
6 mm Nylon Lock Nut
16
C19 T8725SY-C6 8
3.5 mm x 14 mm Round Head ScrewC10 T8725SY-C10 32
Metal BracketC15 T8725SY-C15 8
DETAIL G
C1 T8725SY-C1 3.5 mm x 18 mm Flat Head Screw 48
C10 T8725SY-C10 3.5 mm x 14 mm Round Head Screw 16
C12 T8725SY-C12 Hinge 6
C13 T8725SY-C13 Wheel 4

- 11 -
90 DAY LIMITED WARRANTY
This consumer warranty extends to the original consumer purchase of any ESCALADE SPORTS Product
(hereinafter referred as the“Product”).
WARRANTY DURATION: This Product is warranted to the original consumer purchase of a period of
ninety (90) days from the original purchase.
WARRANTY PERFORMANCE: During the above ninety (90) day warranty period, ESCALADE SPORTS shall
repair or replace with a comparable model, and Product, or component thereof, which may prove
defective under normal use and proper care, and which our examination shall disclose to our
satisfaction to be thus defective, please contact our Warranty Dept.
R
WARRANTY COVERAGE: ESCALADE SPORTS warrants to the original Consumer Purchaser that any
Product of its manufacture is free from defects in material and workmanship when used forthe intended
purpose under normal use and conditions. THIS WARRANTY IS VOID IF THE PRODUCT HAS BEEN DAMAGED
BY ACCIDENT, UNREASONABLE USE, NEGLIGENCE, IMPROPER SERVICE, FAILURE TO FOLLOW INSTRUCTIONS
PROVIDED WITH THE PRODUCT OR OTHER CAUSES NOT ARISING OUT OF DEFECTS IN MATERIAL AND
R
WORKMANSHIP.
R
1-866-873-3528 / Warranty Dept.
Or Write us at:
Escalade Sports, Inc.-P.O. Box 889, Evansville, IN 47706 - Attn: Warranty Dept.
Or E-mail us at:
[e-mail]
Other than shipping requirements no charge will be made for such repair or replacement of in-warranty
Products. ESCALADE SPORTS strongly recommends that the Product is insured forvalue prior to mailing.
R
R
WARRANTY DISCLAIMERS: ANY IMPLIED WARRANTIES ARISING OUT OF THIS SALE, INCLUDING BUT NOT
LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE,
ARE LIMITED IN DURATION TO THE ABOVE NINETY (90) DAY WARRANTY PERIOD. ESCALADE SPORTS SHALL
NOT BE LIABLE FOR LOSS OF USE OF THE PRODUCT OR OTHER CONSEQUENTIAL OR INCIDENTAL COSTS,
EXPENSES OR DAMAGES INCURRED BY THE CONSUMER OF ANY OTHER USE.
R
Some states do notallow theexclusion or limitation of implied warranties or consequential or incidental
damages, so the above limitations or exclusions may notapply to you.
LEGAL REMEDIES: This warranty give you specific legal rights and you may also have other rights which
may vary from state to state.