Stiga T8622 User manual

1. Read this manual carefully before starting assembly. Read each step completely before beginning
each step.
2. Some smaller parts may be shipped inside larger parts. Check inside all parts and cartons
before assembling or ordering parts.
3. To make assembly easier, use the Hardware Identifier on page 13 to identify and sort all
fasteners. Check all cartons for kits. All hardware may not be located in one kit.
4. Do not tighten hardware until instructed to do so. If hardware is tightened too soon, mounting holes
may not align and parts may not easily fit together. Leave locknuts slightly loose until you are instructed to
tighten them.
5. Tools required for assembly: Phillips Screwdriver, 3/8 Wrench, and Two 7/16 Wrenches (adjustable
wrenches may be substituted for the wrenches).
O W N E R ' S M A N U A L
2L-4133-02
2012 Escalade Sports
Escalade® Sports products may be manufactured and/or licensed under the following patents.
6120397, 5816957, 5769744, 5119741, 4911085, 4717157, D460140, D420563
Additional patents may be pending. One or more of the listed patents and/or pending patents may cover specific product.
TABLE TENNIS TABLE
MODEL NOS.
T8622
Contact Escalade® Sports customer service department at:
Phone: [phone] Toll – Free !
Fax: [phone] Toll – Free !
E-mail: [e-mail]
Mailing Address (correspondence only):
Escalade Sports
PO Box 889
Evansville, IN 47706
Please visit our World Wide Web site at: www.escaladesports.com
ON-LINE TROUBLE SHOOTING TECHNICAL ASSISTANCE
ON-LINE PARTS REQUESTS FREQUENTLY ASKED QUESTIONS
ADDITIONAL ESCALADE® SPORTS PRODUCT INFORMATION
Please Do Not Return This Product To The Store!
6. Do not use power tools to drive screws into wood tops. Hand tighten screws only. Tighten
screws snug, but do not overtighten causing screws to strip.
7. Save this instruction and your proof of purchase (receipt) in the event that the manufacturer
has to be contacted for replacement parts.

1
7
For aid in identifying hardware, see hardware identifier on pg 13.
2. Align U-Support (#7) on Table Top as shown in
Figure 1.
1. Lay table top #1 painted side down, on a smooth, flat
surface. Use the shipping container to protect the
painted surface of the table top.
CAUTION:
If you want to see a video on how to position the U-Clips go to:
http://www.escaladesports.com/customer-service/videos.html
Or scan with your smartphone:
WHEN ASSEMBLING TABLE, IT IS EXTREMELY IMPORTANT THAT THE U-CLIPS
(#3) BE TURNED AS SHOWN HERE. IF U-CLIPS ARE TURNED INCORRECTLY,
YOU WILL DO IRREPARABLE DAMAGE TO YOUR TABLE WHEN YOU ATTEMPT
TO OPEN IT TO THE PLAYING POSITION.
20
3
IMPORTANT:
Slot in
U-Clip
End Rail Mounting
Indentations
Detail A
Figure 3
Figure 3
Figure 1
Figure 3
Figure 3
Figure 2
Note: Indentations are
small so look closely.
End Rail Mounting
Indentations
2
3. Align the holes in the U-clips #3 with Indentations in table
top assembly and secure with twelve screws #20 as
shown. All four holes in each U-Clip must align with four
Indentations in top. See Figure 2 and Detail A.
Be sure that slot in the three U-clips #3 all
face the same direction as shown. (Toward
the end of the table with no stripe.)

34
33
20
20
Detail B
4. Align the holes in the Mounting Brackets #33 & #34 with
Indentations in table top assembly and secure with screws #20
as shown. All holes in each Mounting Bracket must align with
Indentations in the top. See Figure 3 and Detail B.
Figure 3
Figure 3
Figure 3
3

5. Attach legs (#2) to Mounting Bracket (#34) with Hex Bolt (#38),
two Plastic Washers (#24) and Locknut (#15). Attach leg brace
to Leg Mounting Bracket (#33) with Phillips Head Screw (#37)
and Locknut (#16) as shown in Detail C.
Figure 3
Figure 3
Figure 4
6.
Figure 4.
Attach leg caps (#13) to bottom of the legs (#2) as shown in
24 15
16 37
2
Leg Brace
38
33
34
Detail C
4
13

29 26
25
20
19
3
7
Note: Rails attach
with #20 screws
Shorter Distance
Longer Distance
35 (RH)
Note: Legs not
shown for Clarity
7.
as shown in Figure 5.
Lay out Side Rails #25 & 29 and End Rails # 26, around edges of
table top.
Figure 3
Figure 3
Figure 5
20
8. Slide Left #36 and Right #35 Vinyl End Caps onto the ends of
the Side Rails #25 & 29 as shown in Detail D.
Detail D
9. Line up holes in rails with indentations in top and secure using
eighteen screws #20. See Figure 5 & Detail D.
10.Lay Corner Caps #22 on table as shown in Figure 5. If
Corner Cap sticks above the table top surface of the table,
flip over so shorter distance is against edge. Secure to
bottom of table with three Screws #21. See Detail E.
Detail E
Detail F
Note: To aid in assembly you can use a cordless drill and
Phillips bit for Step 11 only. Wear safety glasses.
If you want to see a video on how to insert Screw (#19) go to:
http://www.escaladesports.com/customer-service/videos.html
7
11.Insert Screw #19 through slot in U-Clip #3 and
into U-Support #7. Thread it all the way into U-
Support #7 until it touches the back of the tube.
There should be about 3/8 inch of screw #19 left
sticking out. Do not insert screw in middle #3
U-Clip. See Detail F.
Note: Rails attach
with #20 screws
5
Or
Scan with your smartphone:
20
Note: Rotate U-Support #7
until you see the screw hole
in the slot of U-clip #3.
Slide U-support #7 side to
side and front to back if
necessary.

11
12
7
4
23
4
15
31
2
Detail G
Figure 3
Figure 3
Figure 6A
First Table Top
13. On one side of the table attach slotted end of safety strap #6 to INSIDE
of Leg #2 using one bolt #39, one spacer #30, one washer #24, and
one hex nut #15. Tighten hardware until snug but do not overtighten.
Tubes must pivot freely. See Detail H.
14. Attach other end of safety strap #6 to OUTSIDE of linkage #4
using one bolt #9, one washer #24, one spacer #30, and
one hex nut #15 as shown in Detail H.
12. Attach end of linkages #4 with two holes to INSIDE of Leg #2 as shown in Detail
G & Detail H. Secure through end hole with screws #23, locknuts #15 and
plastic spacers #31. Tighten hardware snug enough to keep table stable but do not
overtighten. Tubes must pivot freely.
Important! Do NOT put other safety strap #6 on this
table half. It will be installed on second table half later.
15. Gently tap caster sockets #12 into U-support #7 until flange
on sockets touches the edge of the tube. DO NOT HIT
CASTER SOCKET DIRECTLY WITH A HAMMER! SET A
PIECE OF WOOD ON CASTER SOCKET AND HIT PIECE
OF WOOD TO DRIVE CASTER SOCKET INTO U-
SUPPORT.
16. Insert casters #11 into caster sockets #12.
See Figure 6A.
6
15
24
30
30
6
31
39
23
2
4
924
15

11
12
7
14
24
15
4
23
4
15
31
2
21. Repeat steps from 1-14 on second half. AT LEAST TWO ADULTS ARE NEEDED
TO MOVE TABLE HALF!
CAUTION:
22. Gently tap caster sockets #12 into U-support #7 until flange on sockets
touches the edge of the tube. DO NOT HIT CASTER SOCKET DIRECTLY
WITH A HAMMER! SET A PIECE OF WOOD ON CASTER SOCKET
AND HIT PIECE OF WOOD TO DRIVE CASTER SOCKET INTO U-
SUPPORT.
15
24
30
30
6
31
39
23
2
4
924
15
Detail H
23. Insert casters #11 into caster sockets #12.
24. Attach linkages #4 to the OUTSIDE of U-support #7 on
second table half. Use screws #14, plastic washers #24
and hex nuts #15. See Figure 7.
NOTE: Tighten locknuts #15 finger tight only. They will be
removed when the two table top halves are connected.
Detail G
Figure 3
Figure 3
Figure 7
Second Table Top
NOTE: Tighten locknuts #15 finger tight
only. They will be removed when the two
table top halves are connected.
8

25. Make sure the legs on the first table top half (the half with the name panel #5) are open. With
one person on each side of the table, lift and set table half on its legs. Place table against a
wall as shown above to help stabilize table top half while second half is being attached. Be
sure there is enough room to connect second half.
26. Place a hex bolt #9 and a locknut #15 on floor next to caster wheels (on both sides of the table half) so they will be handy for the next step.
27. With a person on both sides of the second table half, slide the second table half against the first table half. Remove locknuts #15 from screws #14 on second table half
where U-support #7 and linkages #4 join. Align holes in name panels #5 (on first table half) with holes in U-supports (on second table half). Secure second table half to top
hole in name panel #5 using hex bolt #14 installed earlier and locknuts just removed. Secure second table half to bottom hole in name panel #5 with the two hex bolts #9
and locknuts #15 you placed on the floor earlier. Tighten locknuts snug but do not overtighten. These joints must pivot. At this point go back and tighten hex bolts #9.
BE SURE THE FIRST TABLE HALF YOU ASSEMBLED (WITH NAME PANELS #5
ATTACHED) IS STABLE AND AGAINST A WALL. DO NOT LEAVE TABLE HALF
STANDING UNATTENDED.
CAUTION:
UNTIL THE TABLE HALVES ARE CONNECTED THEY WILL NOT STAND ON THEIR
OWN. IT IS RECOMMENDED TO HAVE THREE PEOPLE TO CONNECT TABLE
HALVES. TWO TO STABILIZE TABLE AND ONE TO BOLT TABLE TOGETHER.
9
Figure 3
Figure 3
Figure 8
CAUTION:
9
14
15
5

28. Choose a name panel #5 on either side of the table and install
one safety latch #8 into the right-hand hole on that name panel
as shown in Figures 9 & 10. Use one screw #10 one washer
#17 and one hex nut #16. NOTE: Flange on safety latch
must extend over top of name panel as shown in Figure
9. Safety latch must pivot freely.
29. Go to the other side of the table and install the second safety latch
into the right-hand hole on the other name panel #5. NOTE:
Safety latches must be attached diagonally across
from each other See Figure 10..
INSTALL SAFETY LATCHES #8 AS SHOWN ABOVE FOR PROPER USE OF
TABLE! DO NOT SKIP THIS STEP! DO NOT OPERATE TABLE UNTIL SAFETY
LATCHES ARE INSTALLED AND ASSEMBLY IS COMPLETE!
CAUTION:
10
8
10
Figure 3
Figure 3
Figure 9
Figure 3
Figure 3
Figure 10

TO OPEN:
1. Pull both legs away from table slightly.
2. Stand behind the table near the safety latch.
3. Hold table half with one hand and pivot safety latch enough to
allow the edge of the table half to pass over it.
4. While keeping an eye on the safety latch, pivot table half until it
moves past the safety latch. Once edge of table has passed over
safety latch, stop pivoting table half.
5. With both hands on the table half, center yourself along the table
half and lower the table half to the floor.
6. Repeat for the other table half.
TO CLOSE:
1. Lift table half upward and inward to vertical position.
2. Check to be sure that table half is locked in the safety latch.
3. Repeat for the other table half.
OPENING AND CLOSING INSTRUCTIONS
READ OPERATING INSTRUCTIONS CAREFULLY BEFORE OPERATING TABLE! DO
NOT ALLOW CHILDREN TO OPEN TABLE! DO NOT CLIMB, STAND OR JUMP ON
TABLE! SERIOUS OR FATAL INJURY MAY RESULT! THIS IS NOT A TOY! TABLE IS
TO BE OPENED OR CLOSED BY ADULTS ONLY! FAILURE TO COMPLY WITH
OPENING AND CLOSING INSTRUCTIONS COULD RESULT IN PERSONAL INJURY
OR PROPERTY DAMAGE.
THIS IS A GAME TABLE. DO NOT SIT, STAND, LEAN, WALK OR JUMP
ON TABLE! FAILURE TO COMPLY WITH THIS CAUTION COULD
RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE!
11
CAUTION:
CAUTION:

90 DAY LIMITED WARRANTY
®
This consumer warranty extends to the original consumer purchase of any ESCALADE SPORTS Product
(hereinafter referred as the "Product").
WARRANTY DURATION: This Product is warranted to the original consumer purchase of a period of ninety (90) days from the original
purchase.
WARRANTY COVERAGE: ESCALADE SPORTS warrants to the original Consumer Purchaser that any Product of its manufacture is free from
defects in material and workmanship when used for the intended purpose under normal use and conditions. THIS WARRANTY IS VOID IF THE
PRODUCT HAS BEEN DAMAGED BY ACCIDENT, UNREASONABLE USE, NEGLIGENCE, IMPROPER SERVICE, FAILURE TO FOLLOW
INSTRUCTIONS PROVIDED WITH THE PRODUCT OR OTHER CAUSES NOT ARISING OUT OF DEFECTS IN MATERIAL AND
WORKMANSHIP.
WARRANTY PERFORMANCE: During the above ninety (90) day warranty period, ESCALADE SPORTS shall repair or replace with a
comparable model, and Product, or component thereof, which may prove defective under normal use and proper care, and which our
examination shall disclose to our satisfaction to be thus defective, please contact our Warranty Dept.
1-866-873-3528 / Warranty Dept.
Or Write us at:
Escalade® Sports, Inc. - P.O. Box 889, Evansville, IN 47706 - Attn: Warranty Dept.
Or E-mail us at:
[email protected]
Other than shipping requirements no charge will be made for such repair or replacement of in-warranty Products. ESCALADE®
SPORTS strongly recommends that the Product is insured for value prior to mailing.
WARRANTY DISCLAIMERS: ANY IMPLIED WARRANTIES ARISING OUT OF THIS SALE, INCLUDING BUT NOT LIMITED TO THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO
THE ABOVE NINETY (90) DAY WARRANTY PERIOD. ESCALADE® SPORTS SHALL NOT BE LIABLE FOR LOSS OF USE OF THE
PRODUCT OR OTHER CONSEQUENTIAL OR INCIDENTAL COSTS, EXPENSES OR DAMAGES INCURRED BY THE
CONSUMER OF ANY OTHER USE.
Some states do not allow the exclusion or limitation of implied warranties or consequential or incidental damages, so the above
limitations or exclusions may not apply to you.
LEGAL REMEDIES: This warranty gives you specific legal rights and you may also have other rights which may vary from state to state.
12

(Qty. 6)
1/4-20
Locknut
(Qty. 24)
Zinc
(Qty. 2)
(Qty. 4)
(Qty. 2)
(Qty. 4) (Qty. 4)
(Qty. 6)
(Qty. 100)
(Qty. 16)
(Qty. 4)
(Qty. 4)
S.M.S. (Qty. 4)
#8 x 1 7/16
Sheet Metal Screw
(Qty. 12)
1/4-20 x 3 1/4 Hex Head Bolt
37
38
1/4-20 x 2 1/4 Hex Head Bolt
(Qty. 4)
#10-24 X 1/2 Phillips
Pan Head Screw
(Qty. 4)
CARE AND MAINTENANCE
You have purchased a quality product that will give you years of enjoyment. By following these simple maintenance steps, you will add to the life of
your new table.
THE TABLE TOP
The top (playing surface) of your table is made of particle board. Like all products made of wood, it can be affected by atmospheric changes in both
temperature and humidity. This may cause a slight sag or distortion as the top expands or contracts. This is normal and should not cause concern
as it does not detract from the play or utility value of the table. After assembly of the table, you can minimize the effects of temperature and humidity
changes by storing the table in the folded up position in a dry area when table is not in use.
STORAGE OF YOUR TABLE
This table must be stored indoors to prevent damage to the playing surface. Dampness and extreme temperature changes can cause the wood to
warp, swell, crack or blister. When your table is not in use, it should be folded up in a dry area. Due to the nature of particle board, table top may
bow. Damp and humid conditions will amplify this. This is normal and will not affect playability of table.
CLEANING YOUR TABLE
To clean your table use a soft, damp (NOT WET) cloth only. To prevent damage to your table's playing surface, DO NOT USE ANY CHEMICALS,
ABRASIVE OR CLEANING PRODUCTS on your table's playing surface.
MAINTENANCE OF YOUR TABLE
Be sure to oil all moving parts of your table including the pivot points. This will insure the safety and ease of use of your table.
This table must be kept indoors to prevent damage to the playing surface. Dampness and extreme temperature changes which occur on patios or
similar areas can cause wood to warp, swell, crack or blister.
UNLEVEL FLOORS
If table does not seem level, it is probably due to uneven or unlevel floors. Set the table in its PLAYING POSITION and move table several inches in
different directions to find the best location for the table. If the floor is extremely unlevel, table may not play or operate properly. If table is high in
the center, shim up under the outer U-legs.
13
1/4-20 x 2 1/2 Hex Head Bolt
(Qty. 2)
39
Not UsedNot Used

29
26
1
20
14
Key # Part# Description Qty.
Table Top
Leg & Brace Assembly
1” U-Clip
Linkage
Name Panel
Safety Strap
U-Support
Safety Latch
1/4-20 x 1 1/2 Hex Head Bolt
#10-24 x 3/4 Phillips Round Hd. Screw
2" Caster
Caster Socket
Leg Cap - 1 1/2 OD
1/4-20 x 2 Hex Head Bolt
1/4-20 Locknut
#10-24 Locknut
#10 Flat Washer
Wood Bottom Board
#8-32 x 1 1/4” Sheet Metal Screw
#8 x 7/16 Sheet Metal Screw
#8 x 1 7/16 Hex/Phil Hd. Sheet Metal Screw
Corner Cap - Black
1/4-20 x 3 1/4” Hex Head Bolt
Plastic washer
RH Side Rail -1 1/2" Silver
End Rail-1 1/2” Silver
Net & Posts Kit
Owners Manual - T8622
LH Side Rail - 1 1/2” Silver
5/16" Spacer
3/4" Spacer
1/4-20 X 1-1/4 Hex Head Bolt
Leg Mounting Bracket - 1”
Mounting Bracket
11/2” Vinyl End Cap (Right Hand)
11/2” Vinyl End Cap (Left Hand)
#10-24 x 1/2 Phil. Pan Hd. Screw
1/4-20 x 2 1/4” Hex Head Bolt
1/4-20 X 2 1/2” Hex Head Bolt
4A-5522-00
1A-4131-00
2S-6879-10
8S-6758-03
2S-6422-18
2S-6428-01
8S-6606-04
2S-6264-03
WB-1094-00
1B-4049-01
2Q-6084-00
3M-6115-00
4C-0201-00
WB-1110-00
WN-1008-99
WB-1007-99
2N-0214-99
2W-6269-02
1B-4089-00
1B-6451-00
1B-6951-00
3M-4149-00
1B-6477-00
2B-6087-00
2S-4616-03
2S-4615-02
5A-6700-01
2L-4133-02
2S-4616-04
7B-6257-00
7B-6256-99
1B-6475-00
2S-6343-00
2S-4597-03
3M-4156-00
3M-4157-00
1B-4138-00
WB-1075-00
1B-4137-00
2
4
6
4
2
2
2
2
6
2
4
4
4
4
24
6
2
1
4
100
12
4
4
16
2
2
1
1
2
4
4
4
4
4
2
2
4
4
2
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
PRODUCT PARTS LIST - T8622
2L-4133-02
2
34
38
24
20
33
20
37
34 16
39
9
30
24
31
15
30 24
62
15
23
4
12
11
9
2
9
10
8
14
24
23
31
15
4
13
2
1
7
15
32
18
5
15
16
7
19
19
20
3
3
3
15
15
17
22
21
25
36
35

2L-4133-02
2012 Escalade Sports
Escalade® Sports products may be manufactured and/or licensed under the following patents.
6120397, 5816957, 5769744, 5119741, 4911085, 4717157, D460140, D420563
Additional patents may be pending. One or more of the listed patents and/or pending patents may cover specific product.
MESA DE TENIS
NÚMERO DE MODELÓ
T8622
M A N U A L D E L U S U A R I O
1. Lea este manual cuidadosamente antes de empezar a ensamblar. Lea completamente cada uno de los
pasos antes de empezar cada paso.
2. Algunas partes pequeñas pueden ser empacadas dentro de las partes grandes. Verifique en el interior
de todas las partes y cartones antes de ensamblar o solicitar partes.
3. Para que el ensamblado le sea más fácil, utilice la lista de partes de la página 13 para la identificación
y clasificación de las partes y sus componentes. Busque los juegos de tornillos en todos los cartones.
Todos los tornillos y sus componentes no se encuentren en un sólo juego.
4. No ajuste las partes hasta que las instrucciones se lo indiquen. Si las partes se ajustan antes de lo indicado,
es posible que los orificios no queden alineados, resultando que las partes queden fuera de su lugar y fácilmente no
coincidan. Deje las tuercas de seguridad levemente flojas hasta que las instrucciones le indiquen ajustarlas.
5. Herramientas necesarias: Desarmador Phillips, una llave de 3/8” y dos llaves de 7/16” (Puede utilizar una llave
ajustable tambien).
6. No utilice herramientas eléctricas para atornillar los tornillos en el tablero de madera. Sólo aprietelos con
un desarmador de mano. Apriete los tornillos seguramente, pero no los sobre apriete.
...
Guarde estas instrucciones y recibo de pago en el evento que el fabricador deba de ser contactado
para partes de remplazo.
7.
Visite nuestra página Web internacional: www.escaladesports.com
SOLUCIÓN DE PROBLEMAS POR INTERNET ASISTENCIA TÉCNICA
PEDIDO DE PARTES POR INTERNET PREGUNTAS FRECUENTES
MÁS INFORMACIÓN SOBRE PRODUCTOS DE ESCALADE® SPORTS
Por favor no devuelva este producto a la tienda!
Contacte al departamento de servicio al cliente de Escalade® Sports:
Teléfono: 1-866-873-3528 ¡Sin costo alguno!
Fax: [phone] ¡Sin costo alguno!
E-mail: [email protected]
Apartado postal (sólo para correspondencia):
Escalade Sports
PO Box 889
Evansville, IN 47706

1
7
2.
1.
O escanear con su teléfono inteligente
20
3
IMPORTANTE:
Detalle A
Figura 3
Figura 3
Figura 1
Figura 3
Figura 3
Figura 2
Orificios de guía
para el riel
2
3.
Para identificar los tornillos. Vea la lista de las partes en la página 13.
Coloque sobre una superficie plana y lisa con
el lado pintado hacia abajo. Use la caja en donde venia la
mesa para proteger la pintura de la superficie de la mesa.
el tablero #1
Alinee el Soporte en U (#7) en la mesa como está
mostrado en la Figura 1.
NOTA: Los orificios de
guía son muy pequeños
Ponga atención donde
estan los orificios.
CUANDO ENSAMBLE LA MESA, ES EXTREMADAMENTE IMPORTANTE QUE TODAS LAS (6)
ABRAZADERAS “U” (#3) ESTÉN PUESTAS COMO ESTÁN MOSTRADAS ABAJO. SI LAS
ABRAZADERAS “U” ESTÁN COLOCADAS INCORRECTAMENTE, USTED LE OCASIONARA
DAÑOS IRREPARABLES A SU MESA CUANDO TRATE DE ABRIRLA EN LA POSICIÓN DE JUEGO.
ADVERTENCIA:
Orificios de guía
para el riel
Si desea ver un vídeo de como poner la abrazadera en “U” vaya a:
http://www.escaladesports.com/customer-service/videos.html
Alinee los orificios de las abrazaderas en “U” #3 con los
orificios pequeños que están de guía en el tablero y atornillelos
con los doce tornillos #20. Los cuatro orificios en cada
abrazadera en U #3 deben de estar alineados con los
cuatro orificios en el Tablero. Vea la Figura 2 y el Detalle A.
Esté seguro que la ranura de todas las seis
abrazaderas “U” #3 estén de frente en la
misma dirección (hacia el extremo de la mesa
que no tiene raya) como está mostrado.
Ranura en la
abrazaderas
“U”

34
33
20
20
Detalle B
Figura 3
Figura 3
Figura 3
3
4. Alinee los orificios de los soportes de montaje #33 y #34 con
los orificios de guía en el tablero e inserte los tornillos #20
como se muestra. Todos los orificios en los Soportes #33 y #34
deben de alinearse con los orificios en el tablero. Vea la
Figura 3 y el Detalle B.

Figura 3
Figura 3
Figura 4
24 15
16 37
2
Abrazadera
38
33
34 Detalle C
4
13
6. Inserte los Tapones de las patas (#13) a las Patas (#2) como
se muestra en la Figura 4.
5. Adjunte las patas (#2) al Soporte de Montaje (#34) con el Tornillo de
Cabeza Hexagonal (#38), dos Rondanas de Plástico (#24) y la Tuerca
de Seguridad (#15). Sujete la abrazadera de la pata al soporte (#33)
con el Tornillo Phillips (#37) y Tuerca de Seguridad (#16) como se
muestra en el Detalle C.

29 26
25
20
19
3
7
Shorter Distance
Longer Distance
Nota: Patas no
mostradas
Figura 3
Figura 3
Figura 5
20
Detalle D
Detalle E
Detalle F
7
Nota: Rieles se
instalan con tornillos
#20.
5
20
7. Coloque los rieles #25,#26 y 29, alrededor de los bordes del tablero,
como están mostrados en la Figura 5.
8. Deslice las Tapas de Riel (de mano izquierda #36 y derecha #35) en el
extremo de cada Riel #25 y 29 como se muestra en el Detalle D.
9. Alinee los orificios de los rieles con los orificios de guía del tablero,
atornillelos y asegúrelos con los dieciocho tornillos #20. Vea la
Figura 5 y Detalle D.
10. Coloque los Protectores de Esquina #22 al tablero como
están mostrados en la Figura 5. Si el protector de la
esquina sobresale de la superficie del tablero, volteélo así
que la parte más corta esté en contra del borde. Atornillelos
y asegúrelos por la parte de abajo de la mesa con los
tornillos #21. Vea el Detalle E.
Nota: Para facilitar el ensamblado se puede utilizar un taladro
inalámbrico y una broca Phillips únicamente para el paso 11.
Use anteojos de seguridad.
11. Inserte el tornillo #19 a través de las ranuras de
la abrazadera “U” #3 y dentro del soporte en
forma de U #7. Atornillelo al soporte en U hasta
que toque el fondo del tubo. El tornillo #19 debe
sobresalir acerca de ⅜ de pulgada. No inserte el
tornillo #19 a la abrazadera de en medio. Vea el
Detalle F.
Si desea ver un vídeo de como insertar el Tornillo (#19) vaya a:
http://www.escaladesports.com/customer-service/videos.html
O escanear con su teléfono inteligente
Nota: Rote el soporte en
forma de U #7 hasta que
se vean los orificios a
través de las ranuras de
las abrazaderas en U #3
donde van los tornillos. Si
es necesario deslice el
soporte en forma de U #7
de lado a lado para ver
los orificios.
Nota: Rieles se
instalan con tornillos
#20.
35
Mano
Derecha

11
12
7
4
23
4
15
31
2
15
24
30
30
6
31
39
23
2
4
924
15
Detalle H
Detalle G
Figura 3
Figura 3
Figura 6A
12.
6
En un lado de la mesa una el extremo con la ranura de la correa de
seguridad de metal #6 por la parte de de la pata en “U” #2
usando uno de los tornillos # 39, un separador #30, una rondana #24, y
una tuerca hexagonal #15. Asegurese que las tuercas estén apretadas y
seguras pero no los sobre apriete. Los tubos deben girar libremente. Vea
el Detalle H.
ADENTRO
Una el otro extremo de la correa de seguridad #6 a la
parte de AFUERA del Tubo Conector #4 usando un tornillo #9,
una rondana #24, un separador #30, y una tuerca hexagonal
#15. Como se muestra en el Detalle H.
de metal
Una los extremos de los Tubos Conectores #4 con los dos orificios de ADENTRO de la pata
en “U” #2 como están mostrados en el Detalle G y Detalle H. Atornillelos hasta el final
del orificio con los tornillos # 23, las tuercas de seguridad #15 los separadores de plástico
#31. Asegurese que las tuercas y tornillos estén lo suficientemente apretados y seguros para
mantener la mesa estable pero no los sobre apriete. Los tubos deben girar libremente.
13.
14.
Importante: NO coloque la otra correa #6 en esta mitad de la
mesa. Esta sera instalada en la otra mitad de la mesa después.
Inserte cuidadosamente casquillo de la llanta #12 dentro
del soporte en forma de U #7 hasta que el borde del
casquillo toque el borde del tubo. NO GOLPEE EL
CASQUILLO DIRECTAMENTE CON EL MARTILLO!
COLOQUE UN PEDAZO DE MADERA SOBRE EL
CASQUILLO Y GOLPE SOBRE EL PEDAZO DE
MADERA PARA INSERTAR EL CASQUILLO ADENTRO
DEL SOPORTE EN FORMA DE U.
15.
16. Inserte las llantas #11 adentro del casquillo #12. Vea la
Figura 6A.
Primera Mitad
de la mesa

18
15
32
15
24
14
9
9
4
24
15
32
5
15
7
4
Figura 3
Figura 3
Figura 6B
7
17. Una el otro extremo del Tubo Conector #4 a la parte de AFUERA
del soporte en forma de U #7 con los tornillos # 14 y las rondanas
de plástico #24, luego deslice la Placa #5 sobre los mismos
tornillos # 14 por la parte de ADENTRO del soporte en forma de
U #7. Asegúrelos con las tuercas de seguridad #15. Asegurese
que las tuercas estén apretadas y seguras, pero no las sobre
apriete. Los tubos deben girar libremente.
18. Una la parte de abajo de la placa #5 a los soportes en forma
de U #7. Atornillando los tornillos hexagonales # 9, y las
tuercas de seguridad # 15. Apriete las tuercas, pero esté
seguro de no doblar los tubos. Vea la Figura 6B.
19. Una la Tabla Inferior #18 a las Placas #5,
como se muestra en la Figura 6B. Use
cuatro tornillos #32 y cuatro tuercas de
seguridad #15.
20. Prepare una área para el ensamblado de la Segunda mitad de la mesa. Si es necesario
mueva el primer tablero a un lado con la ayuda de otra persona. Asegúrese de ponerlo en
una lugar donde no estorbe y no se dañe. Y si se coloca de lado, asegurese de poner el
borde inferior a no menos de 12 pulgadas de distancia de la pared. También esté seguro
de poner un pedazo de alfombra o una colchoneta abajo de los bordes de la mesa para
protegerlos. Si el piso no esta alfombrado ponga un objeto pesado sosteniendo la mesa
para que no se resbale.
ADVERTENCIA:
¡POR LO MENOS SE REQUIERE DE DOS (2)
ADULTOS PARA MOVER LA MITAD DE LA MESA!
Primera Mitad
de la mesa
7