Stiga Play The Best T8780Q User manual

2L-4153-00ÓÒÒTABLE TENNIS TABLEMODEL NO.T8780QEscalade® Sports products may be manufactured and/or licensed under the following patents.6120397, 5816957, 5769744, 5119741, 4911085, 4717157, D460140, D420563Additional patents may be pending. One or more of the listed patents and/or pending patents may cover specific product.2013 Escalade SportsOWNER'S MANUALPlease Do Not Return This Product To The Store!Contact Escalade® Sports customer service department at:Phone:[phone]Toll – Free !Fax:[phone]Toll – Free !E-mail:[e-mail] Address (correspondence only):Escalade SportsPO Box 889Evansville, IN 47706Please visit our World Wide Web site at: www.escaladesports.comON-LINE TROUBLE SHOOTINGTECHNICAL ASSISTANCEON-LINE PARTS REQUESTSFREQUENTLY ASKED QUESTIONSADDITIONAL ESCALADE® SPORTS PRODUCT INFORMATION1.Read this manual carefully before starting assembly. Read each step completely before beginning each step.2.Some smaller parts may be shipped inside larger parts. Check inside all parts and cartons before assembling or ordering parts. 5.Tools required for assembly: Phillips Screwdriver, Two 9/16󰾾 Wrenches, Two 7/16󰾾 Wrenches. Note: Adjustable wrenches can be substituted for wrenches.6.Save this instruction manual and your proof of purchase (receipt) in the event that the manufacturer has to be contacted for replacement parts.3.To make assembly easier, use the Hardware Identifier on page 2 to identify and sort allfasteners. Check all cartons for kits. All hardware may not be located in one kit.4.Do not tighten hardware until instructed to do so. If hardware is tightened too soon, mounting holesmay not align and parts may not easily fit together. Leave locknuts slightly loose until you are instructed totighten them.

1/4"PlasticWasherWasherPlastic3/8"28303132333435371/4-20 X 3 1/4 Carriage Bolt(Qty. 4)1/4-20Wing Nut#8 X 9/16SMS#8-32 X 1 1/4Sheet Metal Screw3/8" Long Spacer3/4" Long Spacer3839361/4-20 X 2 3/4 Hex Head Bolt(Qty. 4)29(Qty. 4)(Qty. 4)(Qty. 4)(Qty. 4)(Qty. 4)(Qty. 4)(Qty. 8)HARDWARE IDENTIFIER23/8-16 Nyloc Locknut(Qty. 4)1/4-20 X 1 1/2 Phillips Truss Head Screw(Qty. 4)1/4-20 Nyloc Locknut(Qty. 8)273/8-16 x 3 1/2 Hex Head Bolt(Qty. 4)

31.Attach Wood Bottom Board (#15) to Caster Beam Assemblies (#7) as shown in Figure 1. Turn Caster Beams as shown and attach board with four Carriage Bolts (#31) and four Wing Nuts (#32). Tighten Thumb Screws securely.READ AND FOLLOW ALL ASSEMBLY, OPERATING, ANDSAFETY INSTRUCTIONS CAREFULLY. AT LEAST TWO (2)ADULTS ARE NEEDED TO PUT THIS TABLE TOGETHER!15317323132717736391643Note: Support Plate (#43) must be on inside of Caster Rail (#7) as shown.13743Note: Linkages & Strut tubes must be turned as shown or table will not operate correctly.Figure 1Figure 22.Attach Strut Tubes (#17) and Linkages (#16) to Caster Beam Assemblies (#7) as shown in Figure 2.a) If necessary loosen Bolts (#13) and Nuts (#28) so that Strut Tube (#17) can fit between Support Plate (#43) and Caster Beam (#7) as shown in the Top View and Figure 2.b) Slide one Hex Bolt (#27) through one linkage (#16) one Spacer (#36) pass through Caster Beam (#7), followed by one Plastic Washer (#39), Strut Tube (#17), another Plastic Washer (#39), inner Support Plate (#43) and Lock Nut (#28).c) Repeat on other end of Caster Beam (#7) and on second Caster Beam.d) Tighten Bolts (#13) and Nuts (#28) securely.e) Tighten Nuts (#28) on Bolts (#27) securely.NOTE: Tighten nuts so that end of Bolt (#27) in even with the edge of nut.27281716433912367Top View2813(Inner Plate)2728

Figure 3212235If you want to see a video on how to insert Screw (#35) go to: http://www.escaladesports.com/customer-service/videos.htmlOr Scan with your smartphone:4214.Rotate U-support (#21) that is on bottom of Table Top until you see the screw holes in the slots of U-clips (#22). If necessary Slide U-support (#21) side to side and back and forth to see holes. See Figure 3 & Detail A.5.Insert Screw (#35) through slot in U-clip (#22) and into U-support (#21). See Figure 3 & Detail A. Thread screw all the way into U-support until it touches the back of the tube. There should be about 3/8󰾾 of screw (#35) left sticking out. Repeat for second Screw (#35) and U Clip (#22).Note: To aid in assembly you can use a cordless drill and Phillips bit. Wear safety glasses.3.Lay Table Top (#1) painted side down, on a smooth, flat surface. Use the shipping container to protect the painted surface of table top.1Note: Slide U-Support back and forth until you see the hole if necessary.6.Repeat steps 3-5 on other table top assembly.Detail A

DO NOT OPEN THE TABLE TO PLAYING POSITIONUNTIL BOTH TOPS ARE INSTALLED! DO NOT LEAVETABLE STANDING UNATTENDED. IT COULD BEKNOCKED OVER CAUSING SERIOUS BODILY INJURYOR PROPERTY DAMAGE.AT LEAST TWO (2) ADULTS ARE NEEDED TOCOMPLETE THE REST OF THIS ASSEMBLY! WHENASSEMBLING TOPS TO BASE, HANDLE TOPASSEMBLIES BY GRASPING ONLY THE TOPSTHEMSELVES. DO NOT GRASP METAL LEGS, U-SUPPORT, LINKAGE, OR HINGES. THESE PARTSCAN MOVE AND COULD PINCH FINGERS ORHANDS CAUSING SERIOUS INJURY! ASSEMBLEAS SHOWN WITH LEGS FULLY CLOSED ANDTOPS IN A VERTICAL POSITION. DO NOT OPENY TO ASSEMBLE. TABLE TOPS ARELEGS AND TRHEAVY -ALONE!DO NOT ATTEMPT TO ASSEMBLETUBESUPTable TopAssembly21U-Support17Strut Tube77With at least 2 adults, slide Table Top Assembly onto Strut Tubes (#17).17Strut TubePIVOT STRUTFigure 457.Attach Table Top Assembly to Base Assembly as shown in Figure 4. Pivot Strut Tubes (#17) up as shown; then, with at least one adult on each side of Table Top, lift top and align ends of U-support tube (#21) with tops of Strut Tubes (#17) on Caster Beams (#7) as shown in Figure 4. Slide tubes together.

291616343421331717Spacer goes between Linkage Arm (#16) and Leg (#19)371619293337Figure 58.Secure U-support tube (#21) to Strut Tubes (#17) with two Screws (#33) as shown in Figure 5. Align holes in U-support with holes in Strut Tubes and thread screw (#33) into hole in Strut Tube (#17). Tighten screws all the way but be careful not to over tighten as you could strip threads on screws.9.Attach Linkages (#16) to Leg (#19) as shown in Figure 5. Pivot Leg (#19) out from the table top and pivot both linkages (#16) up and align hole in Linkage with hole in Leg (#19). Attach Linkage (#16) to Leg (#19) using Hex Head Bolt (#29), Spacer (#37) and Locknut (#34). Spacer (#37) goes between Linkage and Leg. Attach other Linkage to Leg the same way. Tighten nuts securely.DO NOT OPEN THE TABLE TO PLAYING POSITION UNTIL BOTH TOPS ARE INSTALLED! DO NOT LEAVE TABLE STANDING UNATTENDED. IT COULD BE KNOCKED OVER CAUSING SERIOUS BODILY INJURY OR PROPERTY DAMAGE.6

7161618Hinge Assembly18Hinge Assembly21171738Plastic Washer goes between Strut Tube (#17) and Hinge (#18)401619CAUTION: Position hinges exactly as shown in Detail L or table will not operate correctly and could be damaged. 3438301817303834301817Detail BATTENTION: If hinge is positioned as shown below (Detail B), Rotate the hinge as shown in Detail C. Do not take hinge off.Detail CIncorrect position of hingeCorrect position of hingeFigure 6In the correct position Hinge #18 will look like a 󰾽V󰾾 when attached to Strut Tube (#17).10.Attach Hinges (#18) to Strut Tubes (#17) as shown in Figure 6 & Detail C. With hinge positioned as shown, align hole in hinge with hole in Strut Tube and attach with ¼󰾾 Screw (#30), Plastic Washer (#38) and Locknut (#34). Plastic Washer (#38) goes between Strut Tube and Hinge. Tighten nut securely. Repeat for other Hinge. CAUTION: Hinges must be positioned exactly as shown or table will not operate correctly and could be damaged.12. With at least two adults, repeat steps 7 through 11 for other table top assembly.DO NOT OPEN THE TABLE TO PLAYING POSITION UNTIL BOTH TOPS ARE INSTALLED! DO NOT LEAVE TABLE STANDING UNATTENDED. IT COULD BE KNOCKED OVER CAUSING SERIOUS BODILY INJURY OR PROPERTY DAMAGE.Note: rotate the hinge to the position shown in Detail C. DO NOT unscrew the hinge, you can rotate the hinge without unscrewing it from the table. If hinge (#18) is positioned as shown in Detail B, you will have to If you want to see a video on how to position hinge (#18) go to: http://www.escaladesports.com/customer-service/videos.htmlOr Scan with your smartphone:11. Attach Corner Protector (#40) to table corners. Push snap tabs on Corner Protector into holes in rails. Be sure that tabs are aligned with holes before pushing. You could break tabs if not aligned correctly.

8 CAUTION:TO CLOSE:1. Remove net and net posts from table.2. Unlock all four hinges.3. Lift one table half to midpoint until the plastic clips are engaged. Then continue lifting until closed.4. Raise other table half in the same manner. as shown in Figure 10.....TO OPEN:1. Hold center of top edge. Gently pull outward to midway position. Continue to pull until disengaged from plastic clips and legs rest on thefloor as shown in Figure 7A and 7B. Do not leave table partially opened at midway position.2. Lower second top as described in step 1.3. Lock all four center hinges. See Figure 8.4. Attach net posts and net to table as shown in Figure 9.NOTE: Net will be tight. It will be necessary to stretch net. This will insureproper net tension..... ........PLAYING POSITIONIF TABLE IS NOT ALIGNING CORRECTLY: (see Figure 11)1. Set the table to the Playing Position and lock hinges as shown inFigure 8.2. Loosen Wing Nuts (#32) attached to bolt (#31) in order to createenough slack to align table tops. See Figure 1.3. With the help of two other adults, push the two table top halves so they are in line with each other and re-tighten the Wing Nuts (#32) as shown in Figure 11. .... ............OPENING AND CLOSING INSTRUCTIONSPush to lock hinge.PlasticClipEXERCISE CAUTION IN OPENING/CLOSING TABLE. SMALL CHILDREN, ORCHILDREN NOT PROPERLY INSTRUCTED IN ITS USE, MUST NOT BE ALLOWED TO OPEN/CLOSE TABLE. IMPROPER HANDLING AND MISUSE CAN RESULT IN SERIOUS INJURY OR DAMAGE. DO NOT CLIMB, STAND, OR JUMP ON TABLE. MOISTURE AND CONDENSATION WILL DAMAGE PLAYING SURFACE OF THIS TABLE. STORE IN DRY, INDOOR PLACE.MidwayPositionPLAYBACK POSITIONHinge LockedTo lock hinge push up on the table and push hinge as shown in Figure 7B.STORAGE POSITIONTOP VIEWFigure 11Figure 10Figure 9Figure 8Figure 7AFigure 7B

9ONE YEAR LIMITED WARRANTYThis consumer warranty extends to the original consumer purchase of any ESCALADE® SPORTS Product(hereinafter referred as the "Product").WARRANTY DURATION: This Product is warranted to the original consumer purchase of a period of one (1) year from the originalpurchase.WARRANTY COVERAGE:ESCALADE SPORTS warrants to the original Consumer Purchaser that any Product of its manufacture is free fromdefects in material and workmanship when used for the intended purpose under normal use and conditions. THIS WARRANTY IS VOID IF THEPRODUCT HAS BEEN DAMAGED BY ACCIDENT, UNREASONABLE USE, NEGLIGENCE, IMPROPER SERVICE, FAILURE TO FOLLOW IN-STRUCTIONS PROVIDED WITH THE PRODUCT OR OTHER CAUSES NOT ARISING OUT OF DEFECTS IN MATERIAL AND WORK-MANSHIP.WARRANTY PERFORMANCE:During the above one (1) year warranty period, ESCALADE SPORTS shall repair or replace with acomparable model, and Product, or component thereof, which may prove defective under normal use and proper care, and which ourexamination shall disclose to our satisfaction to be thus defective, please contact our Warranty Dept.arranty Dept.Or Write us at:Escalade® Sports, Inc. - P.O. Box 889, Evansville, IN 47706 - Attn: Warranty Dept.Or E-mail us at:[e-mail] than shipping requirements no charge will be made for such repair or replacement of in-warranty Products. ESCALADE® SPORTSstrongly recommends that the Product is insured for value prior to mailing.WARRANTY DISCLAIMERS: ANY IMPLIED WARRANTIES ARISING OUT OF THIS SALE, INCLUDING BUT NOT LIMITED TO THEIMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THEABOVE ONE (1) YEAR WARRANTY PERIOD. ESCALADE® SPORTS SHALL NOT BE LIABLE FOR LOSS OF USE OF THE PRODUCT OROTHER CONSEQUENTIAL OR INCIDENTAL COSTS, EXPENSES OR DAMAGES INCURRED BY THE CONSUMER OF ANY OTHER USE.Some states do not allow the exclusion or limitation of implied warranties or consequential or incidental damages, so the abovelimitations or exclusions may not apply to you.LEGAL REMEDIES: This warranty gives you specific legal rights and you may also have other rights which may vary from state to state.CARE AND MAINTENANCEYou have purchased a quality product that will give you years of enjoyment. By following these simple maintenance steps, you will add to the life of your new table.THE TABLE TOPThe top (playing surface) of your table is made of particle board or MDF. Like all products made of wood, it can be affected by atmospheric changes in both temperature and humidity. This may cause a slight sag or distortion as the top expands or contracts. This is normal and should not cause concern as it does not detract from the play or utility value of the table. After assembly of the table, you can minimize the effects of temperature and humidity changes by storing the table in the folded up position in a dry area when table is not in use.STORAGE OF YOUR TABLEThis table must be stored indoors to prevent damage to the playing surface. Dampness and extreme temperature changes can cause the wood to warp, swell, crack or blister. When your table is not in use, it should be folded up in a dry area. Due to the nature of particle board, table top may bow. Damp and humid conditions will amplify this. This is normal and will not affect playability of table.CLEANING YOUR TABLETo clean your table use a soft, damp (NOT WET) cloth only. To prevent damage to your table's playing surface, DO NOT USE ANY CHEMICALS, ABRASIVE OR CLEANING PRODUCTS on your table's playing surface.MAINTENANCE OF YOUR TABLEBe sure to oil all moving parts of your table including the pivot points. This will insure the safety and ease of use of your table.This table must be kept indoors to prevent damage to the playing surface. Dampness and extreme temperature changes which occur on patios or similar areas can cause wood to warp, swell, crack or blister.UNLEVEL FLOORSIf table does not seem level, it is probably due to uneven or unlevel floors. Set the table in its PLAYING POSITION and move table several inches in different directions to find the best location for the table. If the floor is extremely unlevel, table may not play or operate properly. If table is high in the center, shim up under the outer U-legs.1-866-873-3528 / W

4
2
3
1
5
44
38
45
29
24
26
30
38
34
5
6
22
5
21
20
5
40
5
3437
34
2
3
4
18
25
19
2L-4153-00
Key# Part # Description Qty.
4A-5434-00
2S-6715-14
2S-6716-14
2S-6714-12
1B-4082-99
3M-6273-00
4A-7609-05
8S-6841-02
2Q-4017-00
2Q-4018-00
2B-4043-00
3M-6884-00
1B-6195-00
3M-6274-00
2W-6258-02
8S-6842-02
8S-6850-05
4A-5423-02
8S-6866-01
2S-4597-01
8S-6851-01
2S-6879-10
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
5/8" BLUE TOP ONLY
SIDE RAIL - RIGHT HAND
SIDE RAIL - LEFT HAND
END RAIL
#8 X 9/16 SHEET METAL SCREW
U-SUPPORT CLIP (PLASTIC)
CASTER BEAM ASSEMBLY
CASTER BEAM ONLY
3" CASTER - NON LOCKING
3" CASTER - WITH LOCK
3/8" PUSH NUT
STOP SPOOL
3/8-16 X 2 3/4 HEX HEAD BOLT
TUBE PLUG - 1" X 2"
BOTTOM BOARD
LINKAGE
STRUT TUBE
HINGE & MOUNTING BRACKET ASSEMBLY
LEG - BLUE
MOUNTING BRACKET ONLY
U SUPPORT
1" U-CLIP
2
2
2
2
124
8
2
2
2
2
4
8
8
4
1
4
4
4
4
4
2
6
Replacement Parts List for Model Number T8780Q
3B-4002-99
1B-4137-00
1A-6341-01
3M-6248-00
1B-6495-00
2B-4053-00
1B-4135-00
1B-4097-01
1B-6459-00
1N-0001-00
1B-4082-99
2B-4047-98
1B-4089-00
7B-4061-00
7B-6161-00
2B-6087-00
2B-4054-00
3M-6715-00
5A-6700-01
2L-4153-00
2S-6875-02
3B-6007-00
2B-4035-00
1/8 X 1/8 PULL RIVET
1/4-20 x 2 1/2”HEX HEAD BOLT
CROSS TUBE
2" SQUARE PLUG
3/8-16 X 3 1/2 HEX HEAD BOLT
3/8-16 NYLOC JAM NUT
1/4-20 X 2 3/4 HEX HEAD BOLT
1/4-20 X 1 1/2 PHILLIPS HEAD SCREW
1/4-20 X 3 1/4 CARRIAGE BOLT
1/4-20 WING NUT
#8 X 9/16 SHEET METAL SCREW
1/4-20 NYLOC JAM NUT
#8-32 X 1 1/4 SHEET METAL SCREW
3/4 OD X 13/32 ID X 3/4 LONG SPACER
1/2 OD X 9/32 ID X 3/8 LONG SPACER
1/4" PLASTIC WASHER
3/8" PLASTIC WASHER
CORNER PROTECTOR
66" NET & POST SET (NOT SHOWN)
OWNERS MANUAL - T8780Q
SUPPORT PLATE
RIVET 1/4” X 2 3/8”
1/4” PUSH NUT
4
8
2
4
4
12
4
4
4
4
4
16
4
4
4
8
8
4
1
1
4
4
4
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
10
8
13
14
10
16
17
16
8
9
16
28
12
39
32
17
17
31
27
36
13
43
28
16
17
15 11
33