Stiga T8623 User manual

Please Do Not Return This Product To The Store!
Contact Escalade® Sports customer service department at:
Phone: [phone] Toll – Free !
Fax: [phone] Toll – Free !
E-mail: [e-mail]
Mailing Address (correspondence only):
Escalade Sports
PO Box 889
Evansville, IN 47706
Please visit our World Wide Web site at: www.escaladesports.com
ON-LINE TROUBLE SHOOTING TECHNICAL ASSISTANCE
ON-LINE PARTS REQUESTS FREQUENTLY ASKED QUESTIONS
ADDITIONAL ESCALADE® SPORTS PRODUCT INFORMATION
2L-4134-02
ÓÒÒ
TABLE TENNIS TABLE
MODEL NO.
T8623
1. Read this manual carefully before starting assembly. Read each step completely before beginning
each step.
2. Some smaller parts may be shipped inside larger parts. Check inside all parts and cartons
before assembling or ordering parts.
5. Tools required for assembly: Phillips Screwdriver, Two 9/16” Wrenches, Two 7/16” Wrenches.
Note: Adjustable wrenches can be substituted for wrenches.
6. Save this instruction manual and your proof of purchase (receipt) in the event that the
manufacturer has to be contacted for replacement parts.
Escalade® Sports products may be manufactured and/or licensed under the following patents.
6120397, 5816957, 5769744, 5119741, 4911085, 4717157, D460140, D420563
Additional patents may be pending. One or more of the listed patents and/or pending patents may cover specific product. 2015 Escalade Sports
O W N E R ' S M A N U A L
3. To make assembly easier, use the Hardware Identifier on page 2 to identify and sort all
fasteners. Check all cartons for kits. All hardware may not be located in one kit.
4. Do not tighten hardware until instructed to do so. If hardware is tightened too soon, mounting holes
may not align and parts may not easily fit together. Leave locknuts slightly loose until you are instructed to
tighten them.

2
1/4"
Plastic
Washer Washer
Plastic
3/8"
28 30
31
32 5
34
35 37
1/4-20 X 3 1/4 Carriage Bolt #8 X 9/16
SMS
#8-32 X 1 1/4
Sheet Metal Screw 3/8" Long Spacer
3/4" Long Spacer
39
36
29
HARDWARE IDENTIFIER
3/8-16
Nyloc
Locknut 1/4-20 X 1 1/2 Phillips
Truss Head Screw
1/4-20 Nyloc
Locknut
27
3/8-16 x 3 1/2 Hex Head Bolt
3/8-16X2 3/4 Hex Head Bolt 1/4-20 X 2 1/2” Hex Head Bolt 3/8 Push Nut
13 24 11
(Qty. 4) (Qty. 12)
(Qty. 12)
(Qty. 4) (Qty. 4) (Qty. 164)
(Qty. 4) (Qty. 4) (Qty. 4) (Qty. 12) (Qty. 8)
(Qty. 8) (Qty. 8) (Qty. 4)
38
(Qty. 4)
1/4-20 Wing Nut
#10-24
Locknut
(Qty. 4)
#10-24 X 1/2 Phillips
Pan Head Screw
(Qty. 4)
33

115
64 "
111
64
" 1
11
64
"
1
15
64
"
8
10
10
43
8
11
9
10
1A. Attach Caster Wheels (#9 & #10) to Caster Beam. Slide a Caster Wheel with
Lock (#10) through Caster Beam (#8) and secure it with a Push Nut (#11) as
shown in Figure 1. Gently tap the Push Nut (#11) with a hammer to secure it in
place. On the other end of the Caster Beam attach a Caster Wheel without Lock
(#9). Make sure you have one Caster Wheel with Lock and a Caster Wheel
without Lock for each Caster Beam. Repeat step for second Caster Beam.
2. Lay Support Plates (#43) on Caster Beam (#8) to line up holes, the distance
between middle holes to side holes is different, see Front View of Figure 2.
Attach Stop Spools (#12) and Support Plates (#43) to side of Caster Beam
without logo with Bolts (#13) and Nuts (#28) but do not tighten completely.
See Figure 2.
Repeat step for second Caster Beam.
Figure 1
13
28
43
12
8
Longer
Shorter
Figure 2
Front View
3
Longer
Shorter
Match holes in Support Plate (#43)
with Caster Beam (#8).
14
1B. Attach Tube Plugs (#14) to Caster Beam (#8) as shown in Figure 1.

4
3. Attach Wood Bottom Board (#15) to Caster Beam
Assemblies (#8) as shown in Figure 3. Turn
Caster Beams as shown and attach board with four
Carriage Bolts (#31) and four Wing Nuts (#32).
Tighten Wing Nuts securely.
READ AND FOLLOW ALL ASSEMBLY, OPERATING, AND
SAFETY INSTRUCTIONS CAREFULLY. AT LEAST TWO (2)
ADULTS ARE NEEDED TO PUT THIS TABLE TOGETHER!
4. Attach Strut Tubes (#17) and Linkages (#16) to Caster Beam Assemblies (#8) as shown in Figure 4.
a) If necessary loosen Bolts (#13) and Nuts (#28) so that Strut Tube (#17) can fit between Support
Plate (#43) and Caster Beam (#8) as shown in the Top View and Figure 4.
b) Slide one Hex Bolt (#27) through Support Plate (#43), followed by one Plastic Washer (#39), Strut
Tube (#17), one Plastic Washer (#39), pass through Caster Beam (#8), one Spacer (#36), one
Linkage (#16), and Lock Nut (#28).
c) Repeat on other end of Caster Beam (#8) and on second Caster Beam.
d) Tighten Bolts (#13) and Nuts (#28) securely.
e) Tighten Nuts (#28) on Bolts (#27) securely.
NOTE: Tighten nuts so that end of Bolt (#27) in even with the edge of nut.
15
31
8
32
31
32
8
17
8
36
39
28
27
16
17
16
27
43
39 12
36
28
8
43
Note: Support Plate (#43)
is on the inside of Caster
Rail (#8) as shown.
13
8
43
28
13
Note: Linkages & Strut
tubes must be turned as
shown or table will not
operate correctly.
Figure 3
Figure 4
TOP VIEW

CAUTION:
WHEN ASSEMBLING TABLE, IT IS EXTREMELY IMPORTANT THAT THE U-
CLIPS (#22) BE TURNED AS SHOWN HERE. IF U-CLIPS ARE TURNED
INCORRECTLY, YOU WILL DO IRREPARABLE DAMAGE TO YOUR TABLE
WHEN YOU ATTEMPT TO OPEN IT TO THE PLAYING POSITION.
5
8. Rotate U-support (#21) that is on bottom of Table Top
until you see the screw holes in the slots of U-clips (#22).
If necessary Slide U-support (#21) side to side and back
and forth to see holes. See Figure 5 & Detail B.
9. Insert Screw (#35) through slot in U-clip (#22) and into U-support
(#21). See Figure 5 & Detail B. Thread screw all the way into U-
support until it touches the back of the tube. There should be about
3/8” of screw (#35) left sticking out. Repeat for second Screw (#35)
and U Clip (#22).
Note: To aid in assembly you can use a cordless drill and
Phillips bit for Step 9 only. Wear safety glasses.
5. Lay Table Top (#1) painted side down, on a smooth, flat surface. Use the shipping
container to protect the painted surface of table top.
6. Align the ”U” Support (#21) on Table Top (#1) as shown in Figure 5.
7. Align all four holes in each U-Clip (#22) with the four Indentations in table top.
Be sure that Slot in the Three U-Clips (#22) all face the same direction toward the
end of the table with no stripe and no Indentations. Secure U-Clips (#22) with
Screws (#5) as shown in Figure 5 & Detail A.
Note: All four holes in the U-Clip (#22) must align with four Indentations
in table top. See Detail A.
If you want to see a video on how to insert Screw (#35) go to:
http://www.escaladesports.com/customer-service/videos.html
Or
Scan with your smartphone:
Detail A
Figure 5
21
22
35
1
Note: End with no stripe
and no Indentations.
Detail B
5
21 22
Slot in
U-Clip
Note: All Indentations
guides in table top are
small so look closely.
Note: Indentations in table top are small so look closely.

18
6
5
5
10. Assemble parts to the bottom of the table top with Screws (#5) as shown in Figure 6, Detail
C and Detail D.
a) Align the holes in the Mounting Brackets (#25) & (#20) with Indentations in table top
assembly and secure with screws (#5) as shown. All holes in each Mounting Bracket must
align with Indentations in the top. See Figure 6 and Detail C.
b) Align the holes in the two U-Support Clips (#6) with Indentations in table top. Be sure that
the two U-Support Clips (#6) are positioned exactly as shown in Figure 6 & Detail D.
Figure 6
Detail D 6
6
DO NOT USE A POWER DRIVER TO ATTACH HINGE BRACKET ASSEMBLIES (#18)
YOU COULD STRIP SCREW IN WOOD AND DO IRREPARABLE DAMAGE TO THE
TABLE. DO NOT OVER TIGHTEN SCREWS CAUSING THEM TO STRIP THE WOOD!
DO NOT USE A POWER DRIVER TO ATTACH HINGE BRACKET ASSEMBLIES (#18) YOU
COULD STRIP SCREW IN WOOD AND DO IRREPARABLE DAMAGE TO TABLE. DO NOT
OVER TIGHTEN SCREWS CAUSING THEM TO STRIP THE WOOD!
c) Align the holes in the Hinge Bracket Assembly (#18) with Indentations in table top. Be sure
that Hinge is facing the inside of the table and placed exactly as shown in Figure 6 & Detail D.
NOTE: DO NOT use
a power driver to
attach hinge bracket
assemblies (#18).
20
25
5 5
Detail C
Note: Indentations
in table top are small
so look closely.

11. Attach legs (#19) to Mounting Brackets (#20 & 25) with Hex Bolt
(#24), two Plastic Washers (#38) and Locknut (#34). Attach leg
brace to Leg Mounting Bracket (#25) with Phillips Head Screw
(#29) and Locknut (#33) as shown in Detail E.
12. Attach leg caps (#26) to bottom of the legs (#19) as shown in
Figure 7.
38
34
33
29
19
Leg Brace
24
25 20
Figure 7
Detail E
26
7

3
5
8
5
Detail F
13. Lay out Rails (#2, #3, & #23) around edges of
table top. See Figure 8.
14. Line up holes in rails with Indentations in table top
and secure using Screws (#5). See Figure 8 &
Detail F.
2
23 23
Figure 8
*NOTE: Legs not
shown for clarity.

Figure 9
9
Detail H
5
Detail G
40
40
4
Detail J
18. Repeat steps 5 through 17 for other
table top assembly.
17. Lay Corner Caps #40 on table as shown in Figure 9.
Secure to bottom of table with three Screws (#5). See
Detail H & Detail G.
16. Line up holes in Storage Tray (#4) with Indentations in
table top and attach it to the bottom of the table with
four (#5) screws as shown in Figure 9.
15. If Storage Tray (#4) is not pre-assembled snap the top
and bottom sections together as shown in Detail J.
NOTE: Prepare an area for the assembly of the second table top
half. If necessary, move the first table top half aside with the aid of a
helper. Be sure to place it in a location where it won't be disturbed
or damaged. If setting on its side, be sure to place the bottom edge
no less than 12 inches away form the wall. Also be sure to place
carpet or pieces of the shipping carton down to protect
table top edges. If floor is not carpeted, brace table
top half with a heavy object to keep it from sliding.
*NOTE: Legs not
shown for clarity.
NOTE: If Storage Tray (#4) is not pre-
assembled snap the top and bottom
sections together as shown in Detail J.

10
19. Attach Table Top Assembly to Base Assembly as shown in
Figure 10. Pivot Strut Tubes (#17) up as shown; then, with
at least one adult on each side of Table Top, lift top and
align ends of U-support tube (#21) with tops of Strut Tubes
(#17) on Caster Beams (#8) as shown in Figure 10. Slide
tubes together.
DO NOT OPEN THE TABLE TO PLAYING POSITION
UNTIL BOTH TOPS ARE INSTALLED! DO NOT LEAVE
TABLE STANDING UNATTENDED. IT COULD BE
KNOCKED OVER CAUSING SERIOUS BODILY INJURY
OR PROPERTY DAMAGE.
AT LEAST TWO (2) ADULTS ARE NEEDED TO
COMPLETE THE REST OF THIS ASSEMBLY! WHEN
ASSEMBLING TOPS TO BASE, HANDLE TOP
ASSEMBLIES BY GRASPING ONLY THE TOPS
THEMSELVES. DO NOT GRASP METAL LEGS, U-
SUPPORT, LINKAGE, OR HINGES. THESE PARTS
CAN MOVE AND COULD PINCH FINGERS OR
HANDS CAUSING SERIOUS INJURY! ASSEMBLE
AS SHOWN WITH LEGS FULLY CLOSED AND
TOPS IN A VERTICAL POSITION. DO NOT OPEN
Y TO ASSEMBLE. TABLE TOPS ARE
LEGS AND TR
HEAVY -
ALONE!
DO NOT ATTEMPT TO ASSEMBLE
TUBES UP
21
U-Support
17
Strut Tube
8
8
With at least 2 adults,
slide Table Top Assembly
onto Strut Tubes (#17).
17
Strut Tube
PIVOT STRUT
Figure 10
Table Top
Assembly

16
5
DO NOT OPEN THE TABLE TO PLAYING
POSITION UNTIL BOTH TOPS ARE
INSTALLED! DO NOT LEAVE TABLE
STANDING UNATTENDED. IT COULD
BE KNOCKED OVER CAUSING SERIOUS
BODILY INJURY OR PROPERTY
DAMAGE.
Figure 11
20. Secure U-support tube (#21) to Strut Tubes (#17) with two Screws (#5)
as shown in Figure 11. Align holes in U-support with holes in Strut
Tubes and thread screw (#5) into hole in Strut Tube (#17). Tighten
screws all the way but be careful not to over tighten as you could strip
threads on screws.
21. Attach Linkages (#16) to Leg (#19) as shown in Figure 11. Pivot Leg
(#19) out from the table top and pivot both linkages (#16) up and align
hole in Linkage with hole in Leg (#19). Attach Linkage (#16) to Leg
(#19) using Hex Head Bolt (#24), Spacer (#37) and Locknut (#34).
Spacer (#37) goes between Linkage and Leg. Attach other Linkage
to Leg the same way. Tighten nuts securely.
16
16
21
19
34
37
24
24
34
37
17
17
Spacer goes
between Linkage Arm
(#16) and Leg (#19)
5
11
19

22. Attach Hinges (#18) to Strut Tubes (#17) as shown in Figure 12 &
Detail N. With hinge positioned as shown, align hole in hinge with
hole in Strut Tube and attach with ¼” Screw (#30), Plastic Washer
(#38) and Locknut (#34). Plastic Washer (#38) goes between Strut
Tube and Hinge. Tighten nut securely. Repeat for other Hinge.
CAUTION: Hinges must be positioned exactly as shown or
table will not operate correctly and could be damaged.
23. With at least two adults, repeat steps 19 through 22 for other
table top assembly.
DO NOT OPEN THE TABLE TO PLAYING POSITION UNTIL
BOTH TOPS ARE INSTALLED! DO NOT LEAVE TABLE
STANDING UNATTENDED. IT COULD BE KNOCKED OVER
CAUSING SERIOUS BODILY INJURY OR PROPERTY DAMAGE.
30
38
34
30
38
Plastic Washer goes
between Strut Tube
(#17) and Hinge (#18)
18
Hinge Assembly
18
Hinge Assembly
CAUTION: Position hinges exactly as
shown in Detail N or table will not
operate correctly and could be damaged.
34
38
30
18
17
18
17
Detail M
ATTENTION: If hinge is positioned as
shown below (Detail M), Rotate the hinge
as shown in Detail N. Do not take hinge off.
Detail N
Incorrect position
of hinge
Correct position
of hinge
In the correct position
Hinge #18 will look like a
“V” when attached to Strut
Tube (#17).
Note: If hinge (#18) is positioned as shown in Detail M, you will have to
rotate the hinge to the position shown in Detail N. DO NOT unscrew the
hinge, you can rotate the hinge without unscrewing it from the table.
If you want to see a video on how to position hinge (#18) go to:
http://www.escaladesports.com/customer-service/videos.html
Or
Scan with your smartphone:
Figure 12
12
17
17

13
CAUTION:
TO CLOSE:
1. Remove net and net posts from table.
2. Unlock all four hinges.
3. Lift one table half to midpoint until the
plastic clips are engaged. Then continue
lifting until closed.
4. Raise other table half in the same manner.
....as shown in Figure 16.
TO OPEN:
1. Hold center of top edge. Gently pull outward to midway position.
.... Continue to pull until disengaged from plastic clips and legs rest on the
....floor as shown in Figure 13A and 13B. Do not leave table partially
....opened at midway position.
2. Lower second top as described in step 1.
3. Lock all four center hinges. See Figure 14.
4. Attach net posts and net to table as shown in Figure 15.
NOTE: Net will be tight. It will be necessary to stretch net. This will insure
proper net tension.
PLAYING POSITION
IF TABLE IS NOT ALIGNING CORRECTLY: (see Figure 16)
1. Set the table to the Playing Position and lock hinges as shown in
....Figure 14.
2. Loosen Wing Nuts (#32) attached to bolt (#31) in order to create
....enough slack to align table tops. See .Figure 3
3. With the help of two other adults, push the two table top halves so
.... they are in line with each other and re-tighten the Wing Nuts (#32) as
....shown in .Figure 17
OPENING AND CLOSING INSTRUCTIONS
Push to lock hinge.
Plastic
Clip
EXERCISE CAUTION IN OPENING/CLOSING TABLE. SMALL CHILDREN, OR
CHILDREN NOT PROPERLY INSTRUCTED IN ITS USE, MUST NOT BE ALLOWED TO OPEN/CLOSE
TABLE. IMPROPER HANDLING AND MISUSE CAN RESULT IN SERIOUS INJURY OR DAMAGE.
DO NOT CLIMB, STAND, OR JUMP ON TABLE. MOISTURE AND CONDENSATION WILL
DAMAGE PLAYING SURFACE OF THIS TABLE. STORE IN DRY, INDOOR PLACE.
Midway
Position
PLAYBACK POSITION
Hinge
Locked
To lock hinge push up on
the table and push hinge
as shown in Figure 13B.
STORAGE POSITION
TOP VIEW
Figure 13A Figure 13B
Figure 14
Figure 16
Figure 15
Figure 17

14
ONE YEAR LIMITED WARRANTY
This consumer warranty extends to the original consumer purchase of any ESCALADE® SPORTS Product
(hereinafter referred as the "Product").
WARRANTY DURATION: This Product is warranted to the original consumer purchase of a period of one (1) year from the original
purchase.
WARRANTY COVERAGE:ESCALADE SPORTS warrants to the original Consumer Purchaser that any Product of its manufacture is free from
defects in material and workmanship when used for the intended purpose under normal use and conditions. THIS WARRANTY IS VOID IF THE
PRODUCT HAS BEEN DAMAGED BY ACCIDENT, UNREASONABLE USE, NEGLIGENCE, IMPROPER SERVICE, FAILURE TO FOLLOW IN-
STRUCTIONS PROVIDED WITH THE PRODUCT OR OTHER CAUSES NOT ARISING OUT OF DEFECTS IN MATERIAL AND WORK-
MANSHIP.
WARRANTY PERFORMANCE: During the above one (1) year warranty period, ESCALADE SPORTS shall repair or replace with a
comparable model, and Product, or component thereof, which may prove defective under normal use and proper care, and which our
examination shall disclose to our satisfaction to be thus defective, please contact our Warranty Dept.
arranty Dept.
Or Write us at:
Escalade® Sports, Inc. - P.O. Box 889, Evansville, IN 47706 - Attn: Warranty Dept.
Or E-mail us at:
[e-mail]
Other than shipping requirements no charge will be made for such repair or replacement of in-warranty Products. ESCALADE® SPORTS
strongly recommends that the Product is insured for value prior to mailing.
WARRANTY DISCLAIMERS: ANY IMPLIED WARRANTIES ARISING OUT OF THIS SALE, INCLUDING BUT NOT LIMITED TO THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE
ABOVE ONE (1) YEAR WARRANTY PERIOD. ESCALADE® SPORTS SHALL NOT BE LIABLE FOR LOSS OF USE OF THE PRODUCT OR
OTHER CONSEQUENTIAL OR INCIDENTAL COSTS, EXPENSES OR DAMAGES INCURRED BY THE CONSUMER OF ANY OTHER USE.
Some states do not allow the exclusion or limitation of implied warranties or consequential or incidental damages, so the above
limitations or exclusions may not apply to you.
LEGAL REMEDIES: This warranty gives you specific legal rights and you may also have other rights which may vary from state to state.
CARE AND MAINTENANCE
You have purchased a quality product that will give you years of enjoyment. By following these simple maintenance steps, you will add to the life of your new table.
THE TABLE TOP
The top (playing surface) of your table is made of particle board or MDF. Like all products made of wood, it can be affected by atmospheric changes in both temperature and
humidity. This may cause a slight sag or distortion as the top expands or contracts. This is normal and should not cause concern as it does not detract from the play or utility value
of the table. After assembly of the table, you can minimize the effects of temperature and humidity changes by storing the table in the folded up position in a dry area when table
is not in use.
STORAGE OF YOUR TABLE
This table must be stored indoors to prevent damage to the playing surface. Dampness and extreme temperature changes can cause the wood to warp, swell, crack or blister.
When your table is not in use, it should be folded up in a dry area. Due to the nature of particle board, table top may bow. Damp and humid conditions will amplify this. This is
normal and will not affect playability of table.
CLEANING YOUR TABLE
To clean your table use a soft, damp (NOT WET) cloth only. To prevent damage to your table's playing surface, DO NOT USE ANY CHEMICALS, ABRASIVE OR CLEANING
PRODUCTS on your table's playing surface.
MAINTENANCE OF YOUR TABLE
Be sure to oil all moving parts of your table including the pivot points. This will insure the safety and ease of use of your table.
This table must be kept indoors to prevent damage to the playing surface. Dampness and extreme temperature changes which occur on patios or similar areas can cause wood
to warp, swell, crack or blister.
UNLEVEL FLOORS
If table does not seem level, it is probably due to uneven or unlevel floors. Set the table in its PLAYING POSITION and move table several inches in different directions to find the
best location for the table. If the floor is extremely unlevel, table may not play or operate properly. If table is high in the center, shim up under the outer U-legs.
1-866-873-3528 / W

24
38
24
34
33
29
34
37
8
13
14
10
16
17
16
8
9
16
27
12
39
32
17
17
31
28
36
13
43
28
16
17
15 11
15
2L-4134-02
Replacement Parts List for Model Number T8623
5
30
38
34
22
3437
18
19
2
5
5
5
24
23
23
40
5
2
3
Key# Part # T8623 Description
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
Qty.
4A-5523-00
2S-4644-04
2S-4645-04
3M-4166-02
1B-4082-99
3M-6273-00
NOT USED
8S-6841-09
2Q-4023-02
2Q-4024-02
2B-4043-00
3M-6884-00
1B-6195-00
3M-6274-00
2W-6258-02
8S-6842-02
8S-6850-07
4A-5423-02
1A-4107-00
2S-4597-01
8S-6851-04
2S-6879-10
2S-4661-00
1B-4137-00
2S-6343-00
3M-4147-00
1B-6495-00
2B-4053-00
1B-4138-00
1B-4097-01
1B-6459-00
1N-0001-00
WB-1007-99
2B-4047-98
1B-4089-00
7B-4061-00
7B-6161-00
2B-6087-00
2B-4054-00
3M-4165-00
5A-6700-01
2L-4134-02
2S-6875-01
3/4" Indented Top - Black
Side Rail - Right Hand
Side Rail - Left Hand
Storage Tray Assembly
#8 x 9/16" Sheet Metal Screw
U-Support Clip (Plastic)
NOT USED
Caster Beam Only
3" Caster - Non Locking
3" Caster - With Lock
3/8" Push Nut
Stop Spool
3/8-16 x 2 3/4" Hex Head Bolt
Tube Plug - 1" x 2”
Bottom Board
Linkage
Strut Tube
Hinge & Mounting Bracket Assembly
Leg with Brace Assembly
Mounting Bracket
U-Support
1" U-Clip
End Rail
1/4-20 x 2 1/2" Hex Head Bolt
Leg Mounting Bracket - 1”
1 3/4" Leg Cap
3/8-16 x 3 1/2" Hex Head Bolt
3/8-16 Nyloc Jam Nut
#10-24 x 1/2" Phillips Pan Head Screw
1/4-20 x 1 1/2" Phillips Truss Head Screw
1/4-20 x 3 1/4 Crriage Bolt
1/4-20 Wing Nut
#10-24 Locknut
1/4-20 Nyloc Jam Nut
#8-32 x 1 1/4 Sheet Metal Screw
5/8 OD x 3/8 ID x 3/4" Long Spacer
1/2 OD x 1/4 ID x 3/8" Long Spacer
1/4" Plastic Washer
3/8" Plastic Washer
Corner Protector
66" Net & Posts Set (Not Shown)
Owners Manual - T8623
Support Plate - Black
2
2
2
2
164
8
2
2
2
4
8
8
4
1
4
4
4
4
4
2
6
4
8
4
4
4
12
4
4
4
4
4
12
4
4
4
12
8
4
1
1
4
6
21
20
25
1
40
26
20
25
4

2L-4134-02
ÓÒÒ
2015 Escalade Sports
Por favor NO devuelva este producto a la tienda!
M A N U A L D E L U S U A R I O
Los productos Escalade® Sports se pueden fabricar y/o producir bajo las siguientes patentes.
6120397, 5816957, 5769744, 5119741, 4911085, 4717157, D460140, D420563
Puede haber patentes en trámite. Una o más patentes mencionadas y/o en trámite pueden cubrir productos específicos.
MESA DE TENIS
NÚMERO DE MODELO
T8623
Contacte el departamento de servicio al cliente de Escalade® Sports:
Teléfono: ¡Sin costo alguno!1-866-873-3528
Fax: [phone] ¡Sin costo alguno!
Correo Electronico: [email protected]
Apartado postal (sólo para correspondencia):
Escalade Sports
PO Box 889
Evansville, IN 47706
Visite nuestra página Web internacional: www.escaladesports.com
SOLUCION DE PROBLEMAS POR INTERNET ASISTENCIA TÉCNICA
PEDIDO DE PARTES POR INTERNET PREGUNTAS FRECUENTES
MÁS INFORMACIÓN SOBRE PRODUCTOS DE ESCALADE® SPORTS
1. Lea este manual cuidadosamente antes de empezar a ensamblar. Lea completamente cada uno de los
pasos antes de empezar cada paso.
2. Algunas partes pequeñas pueden ser empacadas dentro de las partes grandes. Verifique en el interior
de todas las partes y cartones antes de ensamblar o solicitar partes.
3. Para que el ensamblado le sea más fácil, utilice la lista de partes de la página 2 para la identificación y
clasificación de las partes y sus componentes. Busque los juegos de tornillos en todos los cartones.
Todos los tornillos y sus componentes no se encuentren en un sólo juego.
4. No ajuste las partes hasta que las instrucciones se lo indiquen. Si las partes se ajustan antes de lo indicado,
es posible que los orificios no queden alineados, resultando que las partes queden fuera de su lugar y fácilmente no
coincidan. Deje las tuercas de seguridad levemente flojas hasta que las instrucciones le indiquen ajustarlas.
5. Herramientas necesarias: Desarmador Phillips, dos llaves de 9/16” y dos llaves de 7/16” (Puede utilizar una llave
ajustable en vez de llaves).
6. Guarde estas instrucciones y recibo de pago en el evento que el fabricador deba de ser contactado
para partes de remplazo.

2
28 30
31
32 5
34
35 37
39
36
IDENTIFICADOR DE TORNILLOS
27
13 24 11
(Cant. 4) (Cant. 12)
(Cant. 12)
(Cant. 4) (Cant. 4)
(Cant. 4) (Cant. 4) (Cant. 4) (Cant. 12) (Cant. 8)
(Cant. 8) (Cant. 8) (Cant. 4)
38
(Cant. 4)
3/8-16 x 3 1/2 Tornillo de Cabeza Hexagonal 1/4-20 Tuerca
de Seguridad
3/8-16
de Seguridad
Tuerca
1/4-20 X 3 1/4 Tornillo de Carruaje
1/4-20 X 1 1/2 Tornillo Phillips
1/4-20 Tuerca de Mariposa
(Cant. 164)
#8 X 9/16
Tornillo SMS
3/8-16X 2 3/4” Tornillo de
Cabeza Hexagonal
1/4-20 X 2 1/2” Tornillo de
Cabeza Hexagonal
Contratuerca
de 3/8”
#8-32 X 1 1/4
de metal
Tornillo para lamina
Separador de 3/4” Separador de 3/8”
1/4"
Rondana
Plastico
de
3/8"
Rondana
Plastico
de
29
#10-24 Tuerca
de seguridad
(Cant. 4)
#10-24 X 1/2 Tornillo
Phillips cabeza redonda
(Cant. 4)
33

115
64 "
111
64
" 1
11
64
"
1
15
64
"
8
10
10
43
1A. Junte las llantas (#9 y #10) a el Carril. Deslice una llanta con seguro
(#10) a través de Carril (#8) y asegurela con una Contratuerca (#11)
como se muestra en la Figura 1. Golpe la Contratuerca (#11)
ligeramente con un martillo para asegurarla en su lugar. En el otro
extremo del carril junte una llanta sin seguro (#9). Asegúrese que
cada carril tenga una llanta con seguro y una llanta sin seguro.
Repita el paso para el segundo Carril.
Figura 1
13
28
43
12
8
Más Corto
Figura 2
3
Más Largo
Alinee los orificios de la Placa de
Soporte (#43) el con Carril (#8).
Vista Frontal
2. Coloque las placas de soporte (#43) en el Carril (#8) para alinear los
orificios, la distancia entre los orificios centrales de los orificios
laterales es diferente, vea la Figura 2 y la Vista Frontal. Junte los
Carretes (#12) y las Placas de Soporte (#43) del lado del Carril sin el
logotipo, con los Tornillos (#13) y las Tuercas (#28) pero no los
apriete completamente. Vea la Figura 2. Repita el paso para el
segundo Carril.
Más Corto
Más Largo
1B. Inserte los Tapones (#14) al Carril (#8) como se muestra en la
Figura 1.
8
11
9
10
14

4
15
31
8
32
31
32
8
17
8
36
39
28
27
16
17
16
27
43
39 12
36
28
8
43
13
8
43
28
13
Figura 3
Figura 4
Vista de Arriba
ADVERTENCIA!
LEA Y SIGA TODAS LAS INSTRUCCIONES DEL
ENSAMBLADO, LAS OPERACIONES Y LAS INSTRUCCIONES
DE SEGURIDAD. POR LO MENOS SE REQUIERE DE DOS (2)
ADULTOS PARA ENSAMBLAR LA MESA!
3. Una la Tabla Inferior (#15) a el Carril con Llantas (#8)
como se muestra en la Figura 3. Voltee los Carriles
como están ilustrados y una la Tabla Inferior con los
cuatro Tornillos de Carruaje (#31) y las cuatro Tuercas
de Mariposa (#32). Atornille tuercas asegurándose
que estén apretadas y seguras.
Nota: La placa de Soporte
(#43) debe de estar en el lado
de adentro del carril con llantas
(#8) como está mostrado.
4. Una los Tubos Estructurales (#17) y los Tubos Conectores (#16) a los Carriles con Llantas (#8) como se muestran en la
Figura 4.
a) Si es necesario afloje los Tornillos (#13) y Tuercas (#28) para que el Tubo Estructural (#17) pueda caber entre la Placa de
Soporte (#43) y Carril con Llantas (#8) como se muestra en la Vista de Arriba y la Figura 4.
b) Inserte un Tornillo de Cabeza Hexagonal (#27) a la Placa de Soporte Interior (#43), seguida por una Rondana de Plástico
(#39), Tubo Estructural (#17), otra Rondana de Plástico (#39), el Carril con Llantas (#8), Placa de Soporte Exterior (#43) un
Separador (#36), Tubo Conector (#16), y Tuerca de Seguridad (#28).
c) Repita en el otro lado del Carril (#8) y en el segundo Carril con Llantas.
d) Apriete Tornillos (#13) y Tuercas (#28) hasta que queden asegurados.
e) Apriete Tuercas (#28) en los Tornillos (#27) hasta que queden asegurados.
NOTA: Apriete tuercas hasta que el extremo del tornillo (#27) quede al mismo nivel que el borde de la tuerca.
Nota: Tubos Conectores y Tubos
Estructurales deben de estar volteados
como se muestra, si no la mesa no
operara correctamente.

Detalle A
Detalle B
Figura 5
5
8. Gire el tubo de soporte "U" (#21) que se encuentra en la
base del tablero, hasta que vea los orificios atravez de las
abrazaderas en “U” (#22) para los tornillos. Si es necesario
deslice el tubo de soporte "U" (#21) de lado a lado y hacia
atrás y adelante para ver los orificios. Ver la Figura 5 y el
Detalle B.
9. Inserte el tornillo (#35) por la ranura de la abrazadera en “U” (#22) y
dentro del tubo de soporte "U" (#21). Vea la Figura 5 y el Detalle B.
Atornillelo hasta que toque el fondo del tubo de soporte. El tornillo
(#35) quedará afuera acerca de 3/8". Repetir para el segundo tornillo
(#35) y la abrazadera en “U” (#22).
ADVERTENCIA:
CUANDO ENSAMBLE LA MESA, ES EXTREMADAMENTE IMPORTANTE QUE TODAS
LAS ABRAZADERAS EN “U” (#22) ESTÉN PUESTAS COMO ESTÁN MOSTRADAS EN
LA FIGURA DE ABAJO. SI LAS ABRAZADERAS EN “U” ESTÁN COLOCADAS
INCORRECTAMENTE, USTED LE OCASIONARA DAÑOS IRREPARABLES A SU MESA
CUANDO TRATE DE ABRIRLA EN LA POSICIÓN DE JUEGO.
1
22
521
22
35
5. Coloque el Tablero (#1) sobre una superficie lisa y plana con el lado
pintado hacia abajo. Use la caja para proteger la pintura de la superficie
del tablero.
6. Alinee el tubo de soporte "U" (#21) sobre el Tablero (#1) como se muestra
en la Figura 5.
7. Alinee los cuatro orificios en cada abrazadera en “U” (#22) con los cuatro
orificios en el tablero. Asegúrese de que la ranura de las abrazaderas en
“U” (#22) apunten en la misma dirección hacia el extremo del tablero sin
raya y sin orificios. Asegure las abrazaderas en “U” (#22) con los Tornillos
(#5) como se muestra en la Figura 5 y en el Detalle A.
Nota: Los cuatro orificios en el la abrazadera en U (#22) deben de
estar alineados con los cuatro orificios en el Tablero. Vea el Detalle A.
Note: Extremo sin raya
y sin orificios de guía.
Si desea ver un vídeo de como insertar el Tornillo (#35) vaya a:
http://www.escaladesports.com/customer-service/videos.html
O escanear con su
teléfono inteligente
Ranura en la
abrazaderas
“U”
21
NOTA: Los orificios de guía son
muy pequeños ponga atención
donde están los orificios.
Nota: Para facilitar el ensamblado se puede utilizar un taladro
inalámbrico y una broca Phillips únicamente para el paso 9.
Use anteojos de seguridad.