Strong SRT 7004 User manual

www.strong.tv
User manual
Bedienungsanleitung
Manuel d’Utilisateur
Manuale utente
Manual del usuario
Manual do Utilizador
Digital High Definition Satellite Receiver
SRT 7004
Picture similar

1
PART 1 • English
English
TABLE OF CONTENTS
1.0 INSTRUCTION 2
1.1 Safety Instructions 2
1.2 Storage 2
1.3 Equipment Set-up 3
1.4 Accessories 3
1.5 Usage of external USB devices 3
2.0 YOUR RECEIVER 4
2.1 Default PIN: 0000 4
2.2 Front panel 4
2.3 Rear panel 4
2.4 Remote Control 4
2.5 Installing the batteries 5
2.6 Using the remote control 6
3.0 CONNECTIONS 6
3.1 Basic connection using a Scart cable 6
3.2 Basic connection using an HDMI cable 6
3.3 Connecting multiple xed LNBs using a DiSEqC 1.0/1.1 switch 6
3.4 Connecting to Ethernet 7
4.0 FIRST TIME INSTALLATION 7
4.1 Installation 7
5.0 QUICK GUIDE FOR USING YOUR RECEIVER 8
6.0 OPERATION 8
6.1 Changing channels 8
6.2 Info banner 9
6.3 Selection of audio language 9
6.4 Teletext 10
6.5 Subtitles 10
6.6 EPG (Electronic Programme Guide) 10
6.7 Favourite channels 10
7.0 MAIN MENU 10
7.1 Installation 10
7.2 Channel 14
7.3 Multimedia 21
8.0 TROUBLESHOOTING 23
9.0 SPECIFICATIONS 24
STRONG declares that this item complies with the basic requirements and other relevant regulations of directives CE 2004/108/EC and 73/23/EC,
RoHS 2002/95/EC
Subject to alterations. In consequence of continuous research and development technical specications, design and appearance of products may
change. HDMI, the HDMI logo and High-Denition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United
States and other countries. Dolby and the double-D symbol are registered trademarks of Dolby Laboratories. All other product names are trademarks or
registered trademarks of their respective owners. © STRONG 2013. All rights reserved.
18 Oct 2013 20:17

2
PART 1 • English
1.0 INSTRUCTION
1.1 Safety Instructions
DO NOT INSTALL YOUR RECEIVER:
 In a closed or poorly ventilated cabinet; directly on top of or under any other
equipment; on a surface which might obstruct the ventilation slots.
DO NOT EXPOSE THE RECEIVER OR ITS ACCESSORIES:
 To direct sunlight or any other equipment that generates heat; to rain or intense
moisture; to intense vibration and to any shock which may cause permanent damage
to your receiver or to any magnetic objects, such as loudspeakers, transformers, etc.
 Do not use a damaged power cord. It may cause a re or an electric shock. Do not
touch a power cord with wet hands. It may cause an electric shock.
 When the receiver is not used for a long period of time, you should unplug the power
cord from the wall socket.
 Do not use alcohol or ammonia based liquids to clean the receiver. If you wish, you
may clean your receiver with a soft lint-free cloth slightly made damp with a mild soap
solution, and only after disconnecting from the mains voltage supply. Make sure no
foreign objects fall through the ventilation slots because this could cause re or an
electric shock.
 Do not place any objects on top of the receiver because this might prevent proper
cooling of the components inside.
Safety Precautions
 Never try to open the receiver. It is dangerous to touch the inside of the receiver
due to high voltages and possible electrical hazards. Opening the receiver will void
the warranty of the product. Refer all maintenance or servicing to suitably qualied
personnel.
 When you are connecting cables, be sure that the receiver is disconnected from the
mains supply voltage. Wait a few seconds after switching o the receiver before you
move the receiver or disconnect any equipment.
 It is a necessity that you only use an approved extension and compatible wiring that
is suitable for the electrical power consumption of the installed equipment. Please
ensure that the electrical power supply corresponds with the voltage on the electrical
identication plate at the back of the receiver.
If the receiver does not operate normally even after strictly following the instructions in this user
manual, it is recommended to consult your dealer.
1.2 Storage
Your receiver and its accessories are stored and delivered in a packaging designed to protect against
electric shocks and moisture. When unpacking it, make sure that all the parts are included and keep
the packaging away from children. When transporting the receiver from one place to another or
if you are returning it under warranty conditions, make sure to repack the receiver in its original

3
PART 1 • English
English
packaging with its accessories. Failing to comply with such packaging procedures could damage the
product and void your warranty.
1.3 Equipment Set-up
We recommend you consult a professional installer to set up your equipment. Otherwise, please
follow the instructions below:
 Refer to the user manual of your TV and your antenna.
 Make sure that the SCART/HDMI cable and outdoor components are in a good
condition and the SCART/HDMI connections are well shielded and from good quality.
This manual provides complete instructions for installing and using this receiver. The following
symbols will serve as follow.
WARNING Indicates warning information.
NOTE Indicates any other additional important or helpful information.
MENU Represents a button on the remote control or the receiver. (Bold Characters)
Move to Represents a menu item within a window. (Italic Characters)
1.4 Accessories
 1 user manual
 1 remote control
 2x batteries (AAA type)
NOTE: The batteries should not be recharged, disassembled, electrically short-
circuited or be mixed or used with other types of batteries. If rechargeable
accumulators instead of batteries are going to be used, we recommend
using (e.g. NiMH) types with low self-discharge to ensure long time
operation of remote control.
1.5 Usage of external USB devices
 It is recommended to use USB 2.0 storage devices. If your device is not compatible to
USB 2.0 specications, multimedia functions of the receiver might not work properly.
 STRONG cannot guarantee compatibility with all types of USB storage devices.
 It is advised not to store important information on USB storage devices used with
the receiver. Always make backups of data on your USB storage device before using
it with this receiver. STRONG will not take responsibility for any loss of information or
circumstances caused by loss of information.
 Please ensure that either the USB device is already formatted to FAT/FAT32, or format
the USB device via your receiver, refer to chapter 7.3 Multimedia for details.

4
PART 1 • English
2.0 YOUR RECEIVER
2.1 Default PIN: 0000
2.2 Front panel
Fig. 1
1. USB: For connection of USB pen drive for software upgrade storage
devices
2. LED display: Shows channel number in operation and time in Standby
3. Power button: Switch the receiver to Standby or On.
4. Standby indicator: Shows power state of the receiver
Green LED - receiver is turned on
Red LED - receiver is in standby mode
5. MENU Open the main menu.
6. Remote control sensor:
Receives the signal from the remote control
7. CH-/CH+: To change channels without using the remote control
8. VOL-/VOL+ Decrease/Increase audio volume.
9. OK Conrm settings.
VOL-/VOL+ and CH+/CH- double as navigation buttons when
in menu.
2.3 Rear panel
Fig. 2
1. Ethernet To connect to a network switch, router or modem
2. SAT IN To connect to the LNB of your satellite dish for reception of
satellite broadcast signal
3. SAT OUT To loop through the satellite signal to a second receiver
4. S / PDIF coaxial To connect to a digital or home cinema audio amplier
5. USB For connection of USB device for Multimedia use
6. HDMI To connect to the HDMI input of your TV using a good quality
HDMI cable.
7. TV SCART To connect to TV using a SCART cable
8. DC power To connect to the original included main power adapter (Input
100 ~240V 50~60Hz/ Output 12 V DC
2.4 Remote Control
Fig. 3
1. q Turns the receiver ON/Standby
2. ! To turn the sound on or o.
3. RED Flexible functions in OSD menu and Teletext
4. GREEN Flexible functions in OSD menu and Teletext.
5. YELLOW Flexible functions in OSD menu and Teletext.
6. BLUE In viewing mode: displays the schedule menu for easy setup
timers; Flexible functions in OSD menu and Teletext.

5
PART 1 • English
English
7. SUBTITLE To select subtitles language out of available ones on the current
channel
8. TEXT To open Teletext if available on the current channel.
9. AUDIO Displays the audio selection menu with selections for available
languages and audio modes
10. RECALL To switch between the last viewed channels.
11. 5 Searches backwards during playback. Each pressing increases the
speed (x2 – x32)
12. 6 Searches forwards during playback. Each pressing increases the
speed (x2 – x32)
13. 7 Jumps to the previous le during playback.
14. 8 Jumps to the next le during playback.
15. 1 Starts/resumes the playback.
16. 2 Freezes the playback of multimedia les.
17. 3 Stops playback of multimedia les.
18. 4 Optional. Please see www . strong . tv
19. MENU To open the main menu in viewing mode or to go one step back
in the menu
20. EXIT Cancellation of current process/exit from main menu to viewing
mode
21. pq Switches to the next/previous channel in viewing mode, switches
to the next/previous page in channel list or moving the highlight
up/down in the menu.
22. OK Viewing mode: Displays the channel list. Menu: activation of the
highlighted item
23. tu Decreasing/increasing the volume level in viewing mode/
navigating through the menus/changing values of settings in a
menu
24. EPG Viewing mode: Displays the EPG (Electronic Programme Guide)
25. Press once to display channel number/name and current/coming
information. Press twice to display detailed event information.
Press three times for transponder/signal strength information.
Press again to get back to viewing mode.
26. V+/V- Increases/decreases the volume level in TV mode
27. FAV To access your favourite channels. Toggles between available
favourite groups
28. GOTO In playback mode: opens the time banner for selection the
moment where to jump.
29. P+/P- Jumps 10 places up or down in channel list.
30. 0-9 Channel number and numeric value input
31. OPT No function
32. TV/RADIO Toggles between TV and radio mode
2.5 Installing the batteries
Fig. 4

6
PART 1 • English
Remove the battery cover from the remote control and put 2x AAA size batteries inside the
compartment.
The diagram inside the battery compartment shows the correct way to install the batteries.
1. Open the cover
2. Install batteries
3. Close the cover
NOTE: The batteries should not be recharged, disassembled, electrically short-
circuited, be mixed or used with other types of batteries.
2.6 Using the remote control
Fig. 5
To use the remote control, point it towards the front of the digital receiver. The remote control has a
range of up to 7 metres from the receiver, if properly aligned towards the IR eye on the front panel.
The remote control will not operate if its path is blocked.
NOTE: Sunlight or very bright light (such as TL lighting) might decrease the
sensitivity of the remote control.
3.0 CONNECTIONS
For basic setup with 1 dish + 1 LNB: Connect the satellite cable to the SAT IN connector on your
receiver. For advanced dish setup, refer to section 3.3
3.1 Basic connection using a Scart cable
Fig. 6
1. Connect the LNB of your satellite antenna to the SAT IN connector of your receiver
using a good quality coax cable and suitable ‘F-connector’ plugs.
2. Connect one end of a good quality Scart cable to the TV SCART connector on your
receiver and the other end to the SCART input of your TV.
3. Plug the power cord to a suitable wall outlet.
3.2 Basic connection using an HDMI cable
Fig. 7
1. Connect the LNB of your satellite antenna to the SAT IN connector of your receiver
using a good quality coax cable and suitable ‘F-connector’ plugs.
2. Connect one end of a good quality HDMI cable to the HDMI output on your receiver
and the other end to the HDMI input of your TV.
3. Plug the power cord to a suitable wall outlet.
3.3 Connecting multiple xed LNBs using a DiSEqC 1.0/1.1
switch
Fig. 8

7
PART 1 • English
English
1. Connect the LNBs of your xed antenna to the inputs of a DiSEqC 1.0/1.1 switch
2. Connect the output or “to receiver” connector of the DiSEqC 1.0/1.1 switch to the SAT
IN connector on your receiver.
3. Refer to section 3.1 or 3.2 for TV and mains connections.
4. Refer to section 7.1.1 for Satellite Settings
3.4 Connecting to Ethernet
Fig. 9
Connect a CAT5 cable (or higher quality) to the RJ45 connector of the unit and the other end to an
existing switch, router or modem. The default setting is Auto (DHCP) for automatically obtaining IPs
and DNS. Select Manual in Menu NetworkNetwork Settings to enter own settings if required. When
setting up manually, you need to provide a unique IP address, Netmask, Gateway and DNS for your
receiver. Refer to the manual of your router or modem to setup properly. The Ping test can be selected
to check your connecting, once setup correctly.
4.0 FIRST TIME INSTALLATION
After all connections have been made properly, switch on your TV and make sure the receiver is
connected to the main power. If you are using the receiver for the rst time or restored to factory
default, the Installation menu will appear on your TV screen. Press the tu buttons to select the OSD
Language of your preference.
Country Select your country.
Pre-installed List Some countries come with a pre-installed channel list.
If not available for your country, the item is not selectable.
Video Output Select the output you prefer to use.
TV Format Select between 16:9FIT. 16:9LB and 4:3LB or 4:3PS
Start Search If the pre-installed list is selected, the receiver will jump to the rst channel in
the list. If no pre-installed list available, the Satellite Setting page will appear.
NOTE: If Germany is selected as country, a German pre-set channels list from
ASTRA 19.2E will be installed. The pre-installed list will work with a single
Universal LNB (LO 9750/10600). If another type of LNB is used, you need to
setup the LNB in the Installation Menu, Satellite Setting.
You can continue with the Installation menu to scan and install further channels as described below
or go to viewing mode by pressing the EXIT button to start enjoying the pre-installed channels
immediately.
4.1 Installation
4.1.1 Satellite Setting
Press pq to highlight the satellite your dish is aimed at. When using a multi feed antenna with more
than 1 LNB, select the satellites your antenna is adjusted for by pressing the OK button and set the
appropriate DiSEqC input for the LNBs Astra 19.2E and Hotbird 13E are pre-selected on DiSEqC 1 and
2. The scan process will then search on all selected satellites.

8
PART 1 • English
If you have a non-standard setup, then please refer to section 7.1.2 of this manual: Congure the
antenna settings for the selected satellite
4.1.2 Signal Adjust
The signal quality bar on the bottom of the screen allows you to ne tune the alignment of your
antenna for optimum reception. Adjust your antenna for maximum possible signal quality. When the
signal cannot be improved anymore, x the dish on this position and press the GREEN Scan button
to continue.
4.1.3 Automatic SAT scan
Press pq tu to highlight the options of choice and press GREEN Scan to start the channel search.
It is recommended to use the default settings.
For details, please refer to section 7.1.4 of this manual: Automatic SAT scan
4.1.4 Channel Search
Your receiver will now perform an automatic channel search. When the process has been completed,
all found channels will be stored and the receiver will switch to the rst found channel. You are now
ready to enjoy your new receiver.
NOTE: If no channels were found during the automatic channel scan, the receiver
will return to the Installation menu. Please select your language again.
5.0 QUICK GUIDE FOR USING YOUR RECEIVER
We at STRONG understand that you can’t wait to enjoy your new HD receiver. The following quick
guide will make you familiar with the basic operation of this device. We do, however, advice you to
read the full manual to get the best performance from your STRONG HD receiver.
To turn your receiver ON or to Standby, press the q button on the remote control.
Choose channels with the pq buttons. Alternatively, you can also enter the channel number with
the 0~9 buttons on the remote control or press OK in viewing mode to display the channel list.
The volume can be adjusted with the tu buttons.
6.0 OPERATION
In viewing mode, several features are available to make watching TV a true pleasure. This paragraph
describes these features. Please also read chapter 7 to get familiar with the menu of your new
receiver.
6.1 Changing channels
There are dierent ways to change channels with your new receiver.
 Via direct access
 Via the channel list
 Via the pq buttons
 Via the RECALL button

9
PART 1 • English
English
6.1.1 Direct access
To gain direct access to a certain channel, simply enter its number with the 0~9 buttons on the
remote control. Channel numbers can be up to four digits long. Entering a number with less than four
digits is possible. Just wait a few seconds (or press OK) and your receiver will switch to the selected
channel.
6.1.2 Channel list
Press OK in viewing mode to display the channel list. Press pq to highlight your channel of choice
and press OK once to select the highlighted channel. The channel list is equipped with a Search
function to make it easier to nd channels. In the channel list, press GREEN and an alphabet popup
will be displayed. Press pq to select the rst letter (or letters) of your channel of choice. Press EXIT to
leave the popup. All channels beginning with the chosen letter(s) will now be displayed. Now select
the channel in the ltered list.
The following buttons are available in the channel list and in viewing mode:
GREEN: Opens an alphabet banner to quickly nd a channel
TV/RADIO: Toggles between TV and radio channels
BLUE: While in channel list, jump to top line, to scroll through satellites list.
In viewing mode:
FAVOURITE: To switch to one of the available favourite lists.
6.1.3 Using the pq buttons
p will switch to a higher channel.
q will switch a lower channel.
6.1.4 Using the RECALL button
Press the RECALL button for switching between the last viewed channels.
6.2 Info banner
At any time during viewing mode you can press the button to get information about the
current channel as well as the current and following programme*. Press twice to view detailed
info of current and following programmes. Press tu to see information about current and next
programme. Press three times to view technical details about the current channel. Press again or
EXIT to close the information.
You can change the on-screen duration of the info banner in the System menu. Please refer to section
7.2.5 for more details.
*Programme information is displayed when available. Availability depends on broadcast.
6.3 Selection of audio language
Some channels support a choice of dierent audio formats and/or languages. To select another audio
stream, press AUDIO in viewing mode. A list with available audio streams will now be displayed. Press
pq to select a stream and conrm with OK. With the tu buttons you can choose between mono
left, mono right or stereo audio.

10
PART 1 • English
6.4 Teletext
Your receiver includes a fully featured Teletext. To access Teletext, press the TEXT button in viewing
mode and press the 0~9 or pq buttons to select the number of the page you wish to see. Subpages
(if loaded and available) can be selected with the tu buttons. The coloured buttons of the remote
control allow you to jump to selected pages directly, as indicated on the bottom of the Teletext
screen. Press TEXT again or EXIT to go back to viewing mode.
6.5 Subtitles
Some programmes support a choice of dierent DVB subtitle languages. Press the SUBTITLE button
in viewing mode to display a list of available subtitle languages. Press pq to select a subtitle
language and conrm with OK.
6.6 EPG (Electronic Programme Guide)
The Electronic Programme Guide is a very useful function that allows you to watch programme
schedules and information on screen. Press the EPG button to activate this guide (you can also
enter EPG via the menu too). Press pq tu to select a channel and u to move the highlight to the
programme list. In the programme list, press pq to select or scroll through programmes and tu to
display programme information for the next/previous days. Press OK to display detailed information
about the selected programme. If there is more than one page of information, press tu to scroll.
Press MENU to go 1 step back, EXIT to leave the EPG.
NOTE: Availability of EPG data depends on broadcast.
Booking a programme from the EPG
Select a programme as described above. Press YELLOW (Book) when you have selected a
programme. This will lead you to the Timer (Schedule) menu. All details are already lled in for you.
Save the timer with OK. To display the list of booked events just press the BLUE button while being in
viewing mode. Please refer to section 7.2.4 for more details.
Press RED or GREEN or P+/P- to jump 10 places in the list. A total of 32 events can be booked.
6.7 Favourite channels
Press the FAV button to access your favourite channels and to toggle between available favourite
groups. Please refer to section 7.2.1 for details on how to create favourite lists.
7.0 MAIN MENU
The Main Menu consists of the following items: Installation, Channel, Multimedia, System, Others and
Network.
7.1 Installation
This menu consists of the following items: Satellite Setting, Automatic SAT Scan, Manual Scan, Satellite
Find, Information. Press the MENU button and tu pq to navigate through the menu.

11
PART 1 • English
English
7.1.1 Satellite Setting
Press the pq buttons to highlight the satellite your dish is aimed at. Its antenna settings will be
shown at the right side. You can enter the right side with the tu buttons and return to the satellite
list with EXIT. From the Satellite Setting menu, you can start a scan by pressing the GREEN button
after you have made the appropriate settings or edit transponders by pressing the RED button.
7.1.2 Congure the antenna settings for the selected satellite
Satellite The name of the selected satellite is shown here.
LNB The setting is Universal LNB (09750/10600) – the most used on the market.
Transponder Select a transponder, known to carry a signal.
DiSEqC 1.0 Select the switch type in use. 4to1(DiSEqC 1.0) or 16to1. (DiSEqC 1.1)
Select Tone Burst if a Legacy 2to1 switch is used.
Uncommitted If uncommitted DiSEqC switches are used, select them here. (Advanced user
setup)
Press tu to set the LNB power. 13/18V is the setting for a Universal LNB.
22K Tone Auto: this setting will follow automatically.
Polarity 13/18V, this setting will follow automatically.
Motor If using a motor, press tu to choose DiSEqC1.2/GOTOX. Then press OK to
show the menu for setting the position for your location.
DiSEqC1.2 Move the motor to the right position for locking the signal like explained
below.
Move Continue: press tu for moving West/East. It will keep moving as long
as the button is kept pressed. By pressing once it will move in 1° step.
Move Step(1): press tu for moving West/East in 0.3° step.
Store Position: to store the current motor position for selected satellite.
Goto Reference: to go to the reference 0° position.
GOTO X Select GOTO X with the tu buttons. Press GREEN to setup your location
coordinates. A pop-up window will appear, in which the following settings
can be made:
Location: Press tu to select one of the pre-set locations. Choose a location nearest to
you. If you know the coordinates of your place of residence, you can choose
Manual and make the following extra adjustments:
Longitude Direction: Choose East or West.
Longitude Angle: Press the 0 ~ 9 buttons to enter the coordinate.
Latitude Direction: Choose North or South.
Latitude Angle: Press the 0 ~ 9 buttons to enter the coordinate.
When all settings have been made, press EXIT to save the data and leave the
window.
Now press OK to enter the DiSEqC1.3 menu.
Move Auto will move the dish to the selected satellite automatically.
For Move Continue, Move Step (1) and Goto Reference please see explanation
above.
SatCR Select On, if you use a SatCR LNB, otherwise leave to O. When On is selected
press YELLOW (Setup SatCR) to enter the Sat setup page.
Position: Select the LNB A or LNB B.

12
PART 1 • English
IF Channel: Select the IF channel number according to the specications of your SatCR
LNB. Note: Any SatCR LNB in the chain needs a dierent IF channel number.
Center Frequency: Select the Center Frequency according to the specications of your SatCR
LNB. Note: Any SatCR LNB in the chain needs a dierent Center Frequency.
Select the store button to nalize your settings or press MENU or EXIT to leave without storing.
7.1.3 Satellite and Transponder edit options
When in Satellite Setting use the RED TP Edit button to edit Satellites and Transponders.
Use tu to switch between Left and Right window. (Satellite List and Transponder List.)
Add: While in the satellite name list: Press YELLOW to add a new satellite. In the
popup window, enter a satellite name with the key table (press u), selecting
a character by using the navigation buttons. Press OK to enter the chosen
character. When you have entered the name, navigate to the  on screen and
press OK on the remote control to conrm the new name. Select the satellites
position E for East and W for West. Longitude: Use the numeric keys to enter
the longitude of the satellite. Save the settings with OK or cancel with EXIT.
While in the Transponder list: Press YELLOW to add a new Transponder. In
the popup window enter the frequency, symbol rate and polarity of the new
transponder.
Delete While in the satellite name list: Press BLUE to delete a satellite from the list.
Press GREEN to delete the selected satellite, select YELLOW to delete all
satellites. Conrm deleting with OK or EXIT to cancel.
While in the Transponder list: Press BLUE to delete a transponder from the list.
Press GREEN to delete the selected transponder, select YELLOW to delete all
transponders. Conrm deleting with OK or EXIT to cancel.
Edit: While in the satellite name list: Press RED Edit to enter the Sat Edit window.
Select the satellites position E for East and W for West. Longitude: Use the
numeric keys to enter the longitude of the satellite. Enter a satellite name
with the key table (press u), selecting a character by using the navigation
buttons. Press OK to enter the chosen character. When you have entered the
name, navigate to the  on screen and press OK on the remote control to
conrm the new name. Save the settings with OK or cancel by EXIT.
While in the Transponder list: Press RED Edit to enter the TP Edit window.
Frequency: Use the numeric keys to enter a known frequency of the satellite
transponder. Symbol Rate: Use the 0 ~ 9 buttons to enter the symbol rate of
the satellite transponder.
Polarity: Press tu to select the polarization of the satellite transponder. V (Vertical) or
H (Horizontal).
After entering all data, press OK and conrm with OK or press EXIT to leave without saving.
Use GREEN to enter to the Automatic scan window.

13
PART 1 • English
English
Note: Deleted satellites and transponders from the pre-installed lists can only be
retrieved by performing a factory reset.
7.1.4 Automatic SAT scan
Select the options if you want to do automatic scan.
Satellite: Select the satellite you wish to scan, as previously set up in the Satellite Setting
menu.
Transponder: Select a transponder which is known to carry a signal to check if reception of
the satellite is possible.
NIT: Network Information Table. If selected On, the receiver will use the NIT
provided by the satellite provider to search for channels. If selected O, the
receiver will search with its pre-installed transponder list.
Programme: Select Free Only to search for Free to Air channels. Select All to include
scrambled channels as well. Note: Scrambled channels cannot be watched
with this receiver.
Scan Mode: Default TP: All stored transponders in the memory will be scanned.
Blind: Slow scan in 2 MHz steps. The receiver will rst scan the whole frequency
band to nd the transponders it can lock on. After gathering all transponders,
it scans the transponders one by one to get all available programmes.
One TP: The transponder selected under Transponder will only be scanned.
Scan Select: Select All Sat to search all satellites you have selected in the Satellite Setting
menu. Select Single Sat to search only the satellite selected under Satellite.
After conguring, press GREEN to start scanning with the selected settings.
Your receiver will now perform an automatic channel search with the scanning progress shown
on screen. During the channel search you can quit the scan process with EXIT or MENU. When the
progress has been completed, all found channels will be stored and the receiver will switch to the rst
found channel.
7.1.5 Manual scan - Scanning by transponder
Select the options if you want to do a manual scan. (Advanced users.)
Satellite: Select the satellite you wish to scan from, as previously set up in the Satellite
Setting menu.
Frequency: Enter a known frequency of a satellite transponder with the 0 ~ 9 buttons on
the remote.
Symbol Rate: Enter the symbol rate of the previously set satellite transponder with the 0 ~ 9
buttons on the remote.
Polarity: Set the polarization of the previously set satellite transponder, V (Vertical) or H
(Horizontal).
NIT: Select On if you want to do a scan starting from the previously set satellite
transponder according to the Network Information Table, as oered by the
Satellite Provider. Select O, to scan just the one transponder.
Programme: Select Free Only to search for Free to Air channels. Select All to include
scrambled channels as well. Note: Scrambled channels cannot be watched
with this receiver.

14
PART 1 • English
After conguring, press GREEN to start scanning with the selected settings.
Your receiver will now perform a channel search with the scanning progress
shown on screen. During the channel search you can quit the scan process by
pressing EXIT or MENU. When the progress has been completed, all found
channels will be stored and the receiver will switch to channel number 1. The
new found channels are added to the end of the list.
Satellite Finder: To help you nding a satellite and peaking the dish for maximum reception,
this item can be very useful. Select the satellite you wish to nd or peak, select
a transponder which is known to carry a signal. Use the signal and quality bar
to nd/peak the satellite. Signal strength and quality above ~70% would be
considered usable.
Information Find technical information about this receiver as Model, Hard and Software
versions and the STRONG website: www . strong . tv. This information might be
asked for if you contact us.
7.2 Channel
Press MENU and select Channel by pressing the tu buttons. Use the pq buttons to select the TV
Channel Editor submenu. Press OK to edit programme settings. Press EXIT to exit the menu.
7.2.1 TV Channel Editor
To edit your programme preferences (rename, move, sort, skip, lock, delete, or favourite), please go
to the TV Channel Editor. Press pq to highlight a channel, BLUE to select a satellite (if more than one
available).
Set favourite programme
Your receiver allows you to store channels in up to 8 favourite lists. Due to the large number of
channels available on satellite nowadays, this can be a very useful function.
1. Select the preferred programme, then press the FAV button.
A Favourite Type window will pop up on screen. The following 8 groups are
available: Music, Sport, Shopping, News, Movie, Talk shows and two personal lists.
All types of Favourite List are represented with an icon.
Please select one (or more) of them. Below the preview window you can see to which
favourite list the programme belongs.
2. Repeat the previous step to select more favourite programmes.
3. To conrm and exit the menu, press EXIT. You will be prompted to conrm the
changes.
Disable favourite TV or radio programme
Repeat step 1 described above and deselect with OK in the Favourite Type window.
View favourite programme
1. In normal viewing mode (no menu mode) press the FAV button repeatedly to display
the lists of favourite programmes. (Or press tu to switch between available favourite
lists.)
2. Select your favourite programme by pq and press OK to switch to it.

15
PART 1 • English
English
3. Now in viewing mode you can select channels from the chosen favourite group only
by pressing pq. If you want to change to the main channel list, toggle the FAV
button in viewing mode until FAV O is displayed.
Delete a TV or radio programme
1. Select the programme you want to delete and press the YELLOW button.
A popup window will appear to decide to delete the selected channels or to delete
all channels. (Re-scan required.) A cross-sign will appear behind the selected channel.
Press OK to delete the programmes. You will be prompted to conrm the changes.
2. Repeat the previous step to delete more programmes.
Skip TV or radio programme
1. Select the programme you want to skip and press the RED button. Then press the
BLUE button.
2. The programme will be marked to skip. The receiver will skip this programme while
zapping between programmes in normal viewing mode (in channel list mode the
skipped channels remain selectable).
3. Repeat the previous step to skip more programmes.
4. To conrm and exit the menu, press EXIT.
Disable a skipped TV or radio programme
Press the BLUE button on the programme marked with the skip symbol.
Move a TV or radio programme
1. Select the programme you want to move, and then press the RED button. Then press
the GREEN button.
2. A move symbol will appear. Press OK.
3. Press pq to select the new position of the programme.
4. Press OK to conrm the new position.
5. Repeat the above steps to move more channels.
Locking programmes
You can lock selected programmes for restricted view.
1. Select the programme you want to lock, and then press the GREEN button. The
programme is now marked as locked.
2. Repeat the previous step to select more programmes
3. To conrm and exit the menu, press EXIT.
4. In viewing mode: When coming to a locked channel: Press exit at the warning popup
and enter your Password.

16
PART 1 • English
Note: Programmes will only be locked when channel lock is set to On in the
System menuParental Control.
Note: We recommend changing of the default password (0000) to one of your
preference. Please refer to chapter 7.2.5 System for more details.
Disable a locked TV or radio programme
Press the GREEN button on the programme marked with the lock symbol.
Rename a TV or radio programme
5. Select the programme you want to rename and press the RED button. Then press the
RED (Name) button. An alphabet popup appears.
6. In the alphabet popup select a character by using the navigation buttons. Press OK to
enter the character. When you have entered the new name, navigate to the  sign on
screen and press OK on the remote control to conrm the new name.
7. To store the changes and exit the menu, press OK.
7.2.2 Sort
Here you can sort your channels in the following orders:
1. Select the programme you want to rename and press the RED button. Then press the
YELLOW button.
2. A popup will appear with the following possibilities:
A-Z/Z-A Sort the channels in alphabetical order (A-Z or Z-A)
TP Sort the channels in frequency order as found on Satellite.(Low- High)
FTA/Scrambled Sort the channels from Free to Air to Scrambled
HD/SD Sort the channels from HD to SD order.
Satellite Sort the channels by satellite.
Note: The 1st time the option is selected, the rst possibility is executed, if you
select the same option again, the 2nd possibility is executed. (Example: 1st
time A-Z/Z-A will yield A-Z order. 2nd time will yield Z-A)
7.2.3 Radio Channel Editor
Press MENU and select Channel using the tu buttons. Use the pq buttons to select the Radio
Channel Editor submenu. Press OK to edit programme settings. Press EXIT to exit the menu. Refer to
7.2.1 for explanations of the menu items.
7.2.4 EPG (Electronic Programme Guide)
Please refer to section 6.6 above.

17
PART 1 • English
English
7.2.5 System
Press MENU and select System.
Select an option and press OK to enter a menu item.
Use tu to adjust the settings.
This menu consists of the following items: Language, OSD Style, Clock setting, TV setup, Adv Timer,
Parental Control, Update&Backup and Factory Setting.
7.2.5.1 Language
Press MENU and select System, then Language.
Select an option and press tu to adjust the setting.
Press EXIT to exit the menu.
OSD Language: Select the preferred language for the On Screen Display.
Audio Language: Select the preferred audio language for watching TV channels. If the
language is not available, the default programme language will be used.
Subtitle Language: Select the preferred subtitle language.
7.2.5.2 OSD Style
OSD Transparency: Select the amount of Transparency you prefer in 8 steps.
Banner Display Time: Set the time-out for the info banner. Possible settings are: Always, 1~30
seconds in several steps.
7.2.5.3 Clock setting
Press MENU and select Clock setting. The menu provides options to adjust the time and date settings.
Press pq to select an option and tu to adjust the setting. Press EXIT to exit the menu.
GMT Usage: Select On for automatic time and date updates from live signal or O for
entering them manually.
Time Zone: Select the Oset from GMT standard time.
Set Date: Enter the date using tu and the numeric buttons when GMT Usage is set to
O.
Set Time: Enter the time using tu and the numeric buttons when GMT Usage is set to
O.
Sleep Time: Enter the duration the unit should continue running before switching itself
o. Select 15 min up to 120 min or O.
Summer Time: Select On or O depending on the year’s period.
7.2.5.4 TV setup
Press MENU and select TV Setting. The menu provides options to adjust the interaction between TV
(monitor) and this receiver. Press pq to select an option and tu to adjust the setting. Press EXIT to
exit the menu.
TV Format
You can set the display format to available settings: