Structural Concepts ADDENDA 86772 User manual

USER MANUALS\86772_ADDENDA_USER MANUAL_PC(L)82_AMB_WALL SERIES_GLS FRT DRS_PASTRY CASE REV L DATE: 07/25/2023
MODEL PC “WALL SERIES” CASES*
> AMBIENT PASTRY UNITS > TISSUE/BAG DISPENSERS > GLASS HINGED FRONT DOORS
PC5682
PC3982.6025
Lineup
PC5682.6744 / Wire
Shelving Racks /
Waste Bin / Solid
Surface Front Shelf
* This Manual Pertains To Models PC3982, PC5682, PC5682.5584A, PC5682.6744, PC5682.6769, PC7482 And Other CDRs.
PC5682.5584 / Solid
Shelving / Waste Bin /
Tissue Box Holders /
Front Shelf
Note: Unit is Similar
to PC5682.6769.
SCC P/N
86772
USER
MANUAL
ADDENDA
®
READ AND SAVE THESE INSTRUCTIONS
Structural Concepts Corp. ∙ 888 E. Porter Rd ∙ Muskegon, MI 49441 Phone: [phone] Fax: [phone] ∙ www.structuralconcepts.com

TABLE OF CONTENTS
2
OVERVIEW / TYPE / COMPLIANCE / WARNINGS / PRECAUTIONS / WIRING / PLUGS ..………...
INSTALLATION / POSITIONING AND ALIGNING / ADJUSTING LEVELERS .…………...…………..
INSTALLATION, CONTINUED: BOLTING ADJOINED UNITS …………………………………………..
INSTALLATION, CONTINUED: PACKAGE LEDGE ADJOINING / HEADER ADJOINMENT /
MIRROR ………………………………………………………………………………………………...
ELECTRICAL FUNDAMENTALS: FIELD WIRED MODELS ……………………………………………..
ELECTRICAL FUNDAMENTALS, CONTINUED: PLUG/CORD UNITS ………………………………...
ELECTRICAL FUNDAMENTALS, CONTINUED: T-8 / FLUORESCENT BULBS ……………………..
ELECTRICAL FUNDAMENTALS, CONTINUED: LED LAMPS ………………………………………….
ELECTRICAL FUNDAMENTALS, CONTINUED: LIGHT SWITCH, RECEPTACLE AND PLUGS ….
MAINTENANCE: SHELF ASSEMBLY REMOVAL ………………………………………………………...
MAINTENANCE, CONTINUED: FRONT FLIP-UP DOOR / WASTE BIN ACCESS
(CERTAIN MODELS ONLY) …..……………………………………………………………………..
MAINTENANCE, CONTINUED: AXIAL EXHAUST FANS / FLIP-DOWN WASTE BIN & TISSUE
BIN ACCESS …………………………………………………………………………………………...
GENERAL CLEANING ………………………………………………………………………………………...
ENGINEERED (SYNTHETIC) QUARTZ CARE AND MAINTENANCE ………………………………….
TROUBLESHOOTING …………………………………………………………………………………………
SERIAL LABEL & LOCATION / INFORMATION LISTED / ADD’L TECH INFO & SERVICE .……....
TECHNICAL SERVICE CONTACT INFORMATION / WARRANTY INFORMATION ...…………...…..
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19

3
OVERVIEW
• These Structural Concepts cases should be installed and
operated according to these instructions to ensure proper
performance. Improper use will void warranty.
• This unit is designed to display of products in ambient
store conditions with a max. temperature of 80 °F (27 °C) .
COMPLIANCE
• Performance issues when in violation of applicable NEC,
federal, state or local electrical codes are not covered by
warranty. See below.
WARNING
Risk of electric shock.
Disconnect ALL ELECTRICAL SOURCES before servicing.
WARNING
ELECTRICAL
HAZARD
COMPLIANCE
This equipment MUST be installed in compliance with all applicable NEC,
federal, state and local electrical and plumbing codes.
PRECAUTIONS
• Following are important precautions to prevent damage
to unit or merchandise. Read carefully!
WIRING DIAGRAM
• Each case has its own wiring diagram folded and in its
own packet. It may be placed near ballast box, field
wiring box, raceway cover, or other related location.
CAUTION! POWER CORD AND PLUG MAINTENANCE
Risk of electric shock. If cord or plug becomes damaged,
replace only with cord and plug of same type.
CAUTION! GFCI BREAKER USE REQUIREMENT
If N.E.C. (National Electric Code) or your local code
requires GFCI (Ground Fault Circuit Interrupter) protection,
you MUST use a GFCI breaker in lieu of a GFCI receptacle.
OVERVIEW / COMPLIANCE / WARNINGS / PRECAUTIONS / WIRING DIAGRAM / CORDS & PLUGS
CAUTION! LAMP REPLACEMENT GUIDELINES
If LED lamps are used, they must be size, shape and overall design.
Any replacements must meet factory specifications.
WARNING: This product can expose you to chemicals, including
Urethane (Ethyl Carbamate), which are known to the state of
California to cause cancer and birth defects or other reproductive
harm. For more information go to P65Warnings.ca.gov.

INSTALLATION / POSITIONING AND ALIGNING / ADJUSTING LEVELERS
4
Slide
Skid
Out
Support
required to
prevent
tipping.
A
B
1. Remove Unit From Skid
Caution! case must always remain supported or
center of gravity will allow case to fall. Slide unit to
rear of skid and tip backward off skid.
Pry Bar
Base
Frame
Leveler
Adjustable
Wrench
Toe-Kick
3. Adjust Levelers
• After case is in proper position, adjust case so it
is level and plumb (see illustration at right).
• You may need to remove front and/or rear
Toe-Kick to access levelers.
• Use adjustable wrench to adjust leveler.
• Depending upon case weight it may be necessary
to use a Pry Bar to accomplish this task.
• Do not use Pry Bar on Toe-Kick as it may buckle.
• Do not use Pry Bar on End Panel as it may chip.
• Use Pry Bar ONLY on Base Frame to avoid
damaging case.
• See illustration and photos at right.
2. Position & Align Case Alongside Others
• Before adjusting levelers, make certain that the
case is in proper position and, if required, aligned
with adjoining case(s). Line up areas A & B as
shown below.
• This may require the
repositioning of the
case you are
installing or the
already positioned
cases
Alternate Leveler Style
Note: Illustrations Shown May Not
Exactly Reflect Every Feature or
Option of Your Particular Case

4. Bolting Adjoined Units
• View shown is after removal of end panel.
• Units are bolted together at locations shown.
• Eight 1/4-20 x 2 1/2” bolts & nuts provided.
5
INSTALLATION, CONTINUED: BOLTING ADJOINED UNITS
1
2
3
4
5