Stryker SIDNE StrykeCam 2 User manual

SIDNE® Stryker Visum™ LED
Surgical Light & StrykeCam™ 2
In-Light Camera Package
0240020832
User Guide

Contents
User Guide.........................................................................................5
Guide de l’utilisateur.................................................................29
Benutzerhandbuch .....................................................................53
Guía del usuario...........................................................................79
Manual do Utilizador ...............................................................103
Manuale d’uso.............................................................................127
Gebruikershandleiding...........................................................151
Brugervejledning .......................................................................177
Käyttöohje .....................................................................................201
Brukerveiledning .......................................................................225
Användarhandbok .....................................................................249
Podręcznik użytkownika.........................................................273
Εγχειρίδιο χρήσης .....................................................................297
用户指南..............................................................................................321
ユーザーガイド..................................................................................345
사용설명서..........................................................................................369

Contents
Warnings and Cautions .................................................... 7
Product Description........................................................... 9
Intended Use...........................................................................9
Package Contents...................................................................9
Setup and Interconnection .......................................... 10
Quick Startup Guide .............................................................10
Installing Driver Upgrade.......................................................10
Connecting the Visum™LED Light and Camera
to SIDNE®..............................................................................12
Operation................................................................................ 13
Operating Room Lights.........................................................15
StrykeCam™ 2 In-Light Camera...........................................19
Perilite ...................................................................................25
Troubleshooting ................................................................ 27

7
Warnings and Cautions
Please read this manual and follow its instructions carefully. e words warning,
caution, and note carry special meanings and should be carefully reviewed:
Warning Indicates risks to the safety of the patient or user. Failure to
follow warnings may result in injury to the patient or user.
Caution Indicates risks to the equipment. Failure to follow cautions
may result in product damage.
Note Provides special information to clarify instructions or present
additional useful information.
An exclamation mark within a triangle is intended to
alert the user to the presence of important operating and
maintenance instructions in the manual.
A lightning bolt within a triangle is intended to warn of
the presence of hazardous voltage. Refer all service to
authorized personnel.
Warning To avoid potential serious injury to the user and the patient
and/or damage to this device, please note the following
warnings:
1. Read this manual thoroughly and be familiar with its contents prior to
using this equipment.
2. Use of the Visum LED Surgical Light and Camera is restricted to
a qualied physician or technician familiar with the device and the
equipment to which it connects. Misusing the Visum™ LED Surgical
Light and Camera may cause injury to the patient and/or damage to
system components.
3. Unpack the package carefully and check if any damage occurred during
shipment. If damage is detected, DO NOT use the equipment.
4. Be aware of the position of the table at all times in relation to the patient
and the surroundings.

8
Warning To avoid potential serious injury to the user and the patient
and/or damage to this device, please note the following
electrical warnings:
1. Always power o the Visum™ LED Surgical Light and Camera when
connecting or disconnecting accessories.
2. Before and aer each use, inspect the cord insulation for cracks, nicks,
cuts, dents, or depressions. Any irregularity will decrease the eectiveness
of the insulation and may result in shocks to the patient or operating
room personnel.

9
Product Description
e SIDNE® Stryker Visum™ LED Surgical Light and StrykeCam™ 2 In-Light
Camera package (Visum LED Surgical Light and Camera package) is a soware
interface between the SIDNE device control system and the Visum™ LED Surgical
Light and Camera that provides voice-activated or touchscreen control of the
Visum LED Light and Camera.
Note: To purchase the SIDNE-compatible version of the Visum LED Surgical
Light and Camera package, contact your local Stryker representative.
Intended Use
e Visum LED Light and Camera package is intended to allow SIDNE users
to control the Visum LED Light and Camera through voice and touchscreen
commands. It is intended for use in any surgery requiring overhead lights and
camera. It can be used in any operating room setting where both the Stryker
Visum LED Light and Camera and the SIDNE device control system are installed.
Package Contents
e Visum LED Light and Camera package includes the following components:
1. 50-foot USB Cable (SIDNE interface cable)
2. SIDNE Visum™ LED Surgical Light and Camera Driver 1.0 USB dongle

10
Setup and Interconnection
Quick Startup Guide
is section outlines the startup instructions for experienced users. Refer to the
relevant section(s) of this manual for further details.
1. Power on the SIDNE® console.
2. Install the Visum™ LED Surgical Light and Camera Driver 1.0 upgrade.
SIDNE will power o.
3. Power on SIDNE. Wait for SIDNE to say, “SIDNE ready” before connecting
the Visum LED Light and Camera.
• ConnectthedeviceadaptercabletotheVisumLEDLightandCamera.
• ConnecttheSIDNEinterfacecabletoSIDNE.
4. Power on the Visum LED Light and Camera. SIDNE should say, “O.R.
Lights connected.”
Installing Driver Upgrade
e SIDNE Visum™ LED Surgical Light and Camera Driver Upgrade 1.0 allows
the SIDNE console to communicate with the Visum LED Light and Camera.
Caution Read the Operational Notes at the end of this procedure
before using the SIDNE console to control the Visum LED
Light and Camera.
Caution Do not attempt to install any other soware driver until the
installation of the Visum™ LED Surgical Light and Camera
Driver is complete and the SIDNE console has restarted.
1. Power on the SIDNE console and wait until SIDNE says, “SIDNE ready.”
2. Insert the dongle into the device-driver dongle port on the front SIDNE
panel (see below).

11
3. Follow the voice instructions given by SIDNE. To avoid equipment damage,
please do not remove the dongle card before SIDNE® says, “Please remove
card.” Aer installation is complete, SIDNE® will power o.
When SIDNE says this... Do this...
“Soware card detected. Please stand by.” Wait for the next instruction.
Do not remove the dongle until
SIDNE says, “Please remove card.”
“Soware installation started. Please wait.” Wait for the next instruction.
“Programming started.”
“10% complete, 20% complete...”
Wait for the next instruction.
“Programming failed.” SIDNE will announce this message
only if the programming failed. If
this occurs, follow the steps below:
1. Remove the dongle,
restart SIDNE, and
insert the dongle.
2. If the same problem
occurs again, contact
Stryker Technical
Support.
“Programming complete. Please wait.” Wait for the next instruction.
“Soware installation complete.” Wait for the next instruction.
“Please remove card.” Remove the dongle.
4. Power SIDNE on. When SIDNE says, “SIDNE ready,” the driver is installed
and ready for use.

12
Connecting the Visum™LED Light and Camera
to SIDNE®
SIDNE can control up to four Visum LED Surgical Lights. To do this, a second
power control box is necessary. Use the Expansion port on the rst power supply
box to control the additional two lights.
To enable SIDNE to control four surgical lights, do the following:
1. Power on the lights and camera.
2. Power on SIDNE. Wait for SIDNE to say, “SIDNE ready.”
3. Connect the USB A – to – B (male) cable from an available SIDNE
device port to the SIDNE port on the rst power supply box.
4. Insert a second Stryker USB A – to – B cable into the expansion port.
5. Connect the 50-foot cable (leading from the expansion port) to the
SIDNE® port on the second power supply box (see diagram).
6. SIDNE should say, “O.R. Lights connected” within 20 seconds aer the
Visum LED Light and Camera and SIDNE have been connected. If this
does not occur, refer to the Troubleshooting section of this manual for
instructions.

13
Operation
Status Bar
e status bar, shown below, appears at the bottom of the monitor screen.
1 2 3
1. Indicates the brightness level of the last light accessed.
2. Indicates the focus setting of the in-light camera.
3. Indicates the the shutter setting of the in-light camera.

14
O.R. Lights Touchscreen

15
Operating Room Lights
Touchscreen Commands
e following table describes the tablet buttons and level meters and their
function.
Button Group Buttons/Levels Description
Light–specic
controls
Power Powers on/o a particular light. Green
indicates the light is on. Blue indicates the
light is o.
Brightness level Increases or decreases the light intensity.
e range is from 1 through 8. If this
button has a gray background, the light
is at the maximum intensity.
High Sets a light to the maximum intensity.
If this button has a gray background,
the light is at the maximum intensity.
Low Sets a light to the minimum intensity.
If this button has a gray background,
the light is at the minimum intensity.
+ Increases the intensity of a light by one
unit. If this button has a gray background,
the light is at the maximum intensity.
- Decreases the intensity of a light by one
unit. If this button has a gray background,
the light is at the minimum intensity.
All light
controls
On Powers on all the lights. If this button has
a gray background, at least one light is on.
O Powers o all the lights. If this button has
a gray background, all lights are o.
High Sets all lights to the maximum intensity.
Low Sets all lights to the minimum intensity.
Brighter Increases the intensity of all lights by one
unit. If this button has a gray background,
the light is at the maximum intensity.
Darker Decreases the intensity of all lights by one
unit. If this button has a gray background,
the light is at the minimum intensity or
is o.

16
LED Lights Menu

17
Voice Commands
e following table shows the SIDNE®voice commands for controlling the
Visum™ LED Surgical Lights.
Top Level Device
Selection
Function Selection Description
SIDNE O. R.
Lights
Light 1, Light 2,
Light 3, or Light 4
Activate Powers on the light.
Brighter Increase the light
intensity by one unit.
Darker Decreases the light
intensity by one unit.
High Sets the light intensity
to maximum.
Low Sets the light intensity
to minimum.
O Powers o the light.
All lights Activate Powers on all the
connected lights.
Brighter Increases the light
intensity of all
connected lights
by one unit.
Darker Decreases the light
intensity of all
connected lights
by one unit.
High Sets the light intensity
of all the connected
lights to maximum.
Low Sets the light intensity
of all the connected
lights to minimum.
O Powers o all the
connected lights.

18
SIDNE®Announcements
Voice Message Playback Condition
Connected Visum™ LED Surgical Lights are powered on and
connected to SIDNE.
Disconnected Visum LED Surgical Lights are disconnected or
powered o.
Light error An error has been reported on one or more
of the connected Visum LED Surgical Lights.
Servicing may be necessary.
O. R. lights … Added as a prex added to a feedback message
when not in the O. R. Lights voice command
menu.
Operating Notes
1. Use the activate or the brightness commands to turn on any light when
the darker and o buttons are gray.
2. A status bar will be displayed on the monitor when using voice control.
e far le section shows the brightness level of the last individual light
accessed using the voice menu or, by default, the lowest numbered light
head connected. Say “Light” with the number of the desired light in the
“O.R. Lights” menu and the status bar will update to show the brightness
of that light. For example, say “Light 2” to see the brightness lights.

19
StrykeCam™ 2 In-Light Camera
Camera Touchscreen Menu

20
Touchscreen Commands
e following table describes the tablet commands and their functions.
Button Group Buttons/Levels Description
Power Power Powers on/o a particular light. Green
indicates the light is on. Blue indicates
the light is o.
Shutter Automatic Sets the camera to automatic shutter
control. Orange indicates the camera
is set to automatic shutter control.
Manual Sets the camera to manual shutter
control. Orange indicates the camera
is set to manual shutter control.
Brighter Increases the shutter speed by one unit.
Gray indicates the camera is at maximum
shutter speed. Using this button will set
the camera to manual shutter mode.
Darker Decreases the shutter speed by one unit.
Gray indicates the camera is at minimum
iris. Using this button will set the camera
to manual iris mode.
Focus Automatic Sets the camera to automatic focus control.
Orange indicates the camera is set to
automatic focus control.
Manual Sets the camera to manual focus control.
Orange indicates the camera is set to
manual focus control.
Focus out Begins to focus out of the current view.
Releasing the button will stop the focus
out. A gray background indicates the
camera is at the maximum focus. Using
this button will set the camera to manual
focus mode.
Focus in Begins to focus into the current view.
Releasing the button will stop the focus in.
A gray background indicates the camera is
at the minimum focus. Using this button
will set the camera to manual focus mode.