Stryker TP600 User manual

T/PUMP®
Series Localized Temperature Therapy System
Système de thermothérapie
Sistema de termoterapia localizada, series
TP600 & TP700
Operations Manual
Manuel d’utilisation
Manual del operador
2014/06 C.1 101515 REV C

Symbols and Definitions
General Warning
Caution
Warm Water Fill Line
Cold Water Fill Line
Attention, consult Operator’s Manual
Water Levels
Water Flow
Dangerous Voltage
Type BF Applied Part
Do not penetrate with sharp object
Medical Electrical Equipment with Respect to Electrical Shock, Fire, and Mechanical hazards in ac-
cordance with UL 60601-1, and CAN/CSA C22.2 No. 601.1, ASTM F 2196-2002
Model or Catalog Number
Manufacturer
SYMBOLS

Table of Contents
Symbols and Definitions ...................................................................1-1
Symbols ...........................................................................1-1
Safety Precautions .......................................................................1-3
Introduction ............................................................................1-4
Before You Begin.....................................................................1-4
Receiving Inspection ..................................................................1-4
To Return Pumps To Factory For Repair Or Exchange..........................................1-4
Introduction .........................................................................1-5
Connecting the Pads ..................................................................1-5
Catalog Descriptions ..................................................................1-6
Indications and Contraindications ............................................................1-7
Indications for Use....................................................................1-7
Clinical Contraindications...............................................................1-7
Features...............................................................................1-8
Pump Features ......................................................................1-8
Keypad Features TP600 Series ..........................................................1-9
Keypad Features TP700 Series .........................................................1-10
Operating Instructions....................................................................1-11
Clik-Tite Connectors..................................................................1-1 1
Colder ............................................................................1-12
Start-Up Procedure ..................................................................1-13
Shutdown Procedure .................................................................1-13
Therapy Cycles ........................................................................1-14
Troubleshooting ........................................................................1-15
Cleaning..............................................................................1-18
Storage / Cleaning...................................................................1-18
Institutional (Hospital) Cleaning Instructions ................................................1-19
Pads / Accessories ..................................................................1-19
Maintenance ..........................................................................1-20
Preventative Maintenance / Service ......................................................1-20
Specifications..........................................................................1-21
EMC Information........................................................................1-22
Warranty .............................................................................1-2 5
Warranties.........................................................................1-25
Pump ............................................................................1-25
Pad, Single Patient Use ...............................................................1-25
Pad, Reusable ......................................................................1-25
Parts .............................................................................1-25
1-2 101515 REV C

101515 REV C 1-3
Safety Precautions
WARNING
• Risk of explosion. Do not use in the presence of flammable anesthetics.
• Risk of electric shock. Disconnect power before servicing the T/Pump.
• Do not attach the power cord to any moving parts of the bed frame or any location that may be a pinch point or
cause power cord damage. If routed improperly, the power cord may become pinched and could cause electrical
shock.
• This device pumps temperature controlled water through a pad. Set the pad temperature only as directed by and
under the guidance of the prescriber.
• Check the skin integrity of the body surface to which therapy is applied. Evaluate patient response to temperature
application.
• Check patient’s skin for adverse reactions every 30 minutes or as directed by the prescriber. Patients at greatest
risk are those who are unconscious, diabetic, and/or incapacitated.
• Failure to adhere to these warnings could result in patient injury.
• The following Groups/Conditions require additional surveillance:
Group/Condition at risk Potential Injury
Patients with impaired circulation Ischemia
Areas of application under pressure Ischemia
• Only qualified medical service personnel should repair the T/Pump. Improper repair may result in death or serious
injury, equipment damage, or malfunction.
• UseT/PumpTP600&TP700seriescontrolswithMul•T•Pads®. For catalog numbers and descriptions, see page
1-6.
• Do not place additional heat sources between the patient and pad. Skin damage may result.
• Do not modify the product or any components of the product. Modifying the product can cause unpredictable
operation resulting in injury to the patient or operator. Modifying the product aslo voids the product warranty.
• Do not use accessories other than those specified by Stryker. Using competitor accessories may result in
unpredictable operation resulting in injury to the patient or operator or damage to the product.
• To avoid the risk of shock, unplug the unit before filling the reservoir.
CAUTION
• U.S. Federal law restricts this device to sale by or on the order of a physician.
• Set fluid temperature and monitor patient’s temperature and skin condition as directed by a physician to prevent
injury.
• Additional surveillance required for pediatric patients and patients with impaired circulation.
• Closely monitor areas of application under pressure as well as with use with topical solutions and other heat
sources to prevent injury.
• The use of quaternary disinfectant products may cause damage to the product.
• Frequent or prolonged exposure to higher concentration disinfectant solutions may result in damage to the product.
• Do not cover the control unit with blankets, pillows or other insulating materials. Air flow is required to maintain
system performance.

1-4 101515 REV C
BEFORE YOU BEGIN
Read and understand this T/PUMP OPERATOR’S MANUAL and all SAFETY PRECAUTIONS
(see page 1-3) prior to using the T/Pump.
Only qualified medical service personnel should repair or perform function tests on the T/Pump. Contact your dealer
or Stryker’s Technical Service Department for assistance:
Telephone: [phone]
RECEIVING INSPECTION
Check the shipping carton for damage immediately upon receipt. If package damage is discovered, the device should
be unpacked with the carrier’s agent present. Any claims for shortage or damage must be filed with the delivering
carrier by the purchaser. Do not return pumps that were damaged in shipment to Stryker without contacting our
Technical Service Department for advice (see phone numbers below). If damaged goods are returned to Stryker
without notifying the carrier, Stryker will assume the repairs will be made at the customer’s expense.
To Return Pumps To Factory For Repair Or Exchange
Merchandise returned to Stryker must be accompanied by a Return Goods Number (RG#), issued by Stryker,
authorizing goods to be returned. Contact Customer Service at:
Customer Service: [phone]
Introduction

101515 REV C 1-5
INTRODUCTION
WARNING
• Do not modify the product or any components of the product. Modifying the product can cause unpredictable
operation resulting in injury to the patient or operator. Modifying the product aslo voids the product warranty.
• Do not use accessories other than those specified by Stryker. Using competitor accessories may result in
unpredictable operation resulting in injury to the patient or operator or damage to the product.
CAUTION
• U.S. Federal law restricts this device to sale by or on the order of a physician.
• Do not cover the control unit with blankets, pillows or other insulating materials. Air flow is required to maintain
system performance.
Heat therapy is effective in the dilation of blood vessels, thereby increasing the blood flow to the heated area. Heat
therapy has a variety of uses, the most common being treatment of aches and pains in joints and muscles.
Cooling therapy assists in vasoconstriction, decreasing blood flow and decreasing the metabolism in the affected area.
Cooling therapy is applied in the acute phase of injury minimizing blood loss, inflammation of the tissue, and can be
effective in pain management.
The Stryker T/Pump®Localized Temperature Therapy System provides therapy by warming or cooling the enclosed
water,andcirculatingitthroughtheStrykerMul•T•Pad.ThepadisconnectedtotheStrykerT/Pumpwith
easy-to-use Clik-Tite®or Colder.
TheMul•T•Pad®provides the interface for delivering the temperature therapy. The unique button design allows water
to flow and provides trouble-free operation when the pad is folded to form a customized fit. This reduces the number
of pads your facility must keep in inventory. The pads are applied to the part of the body requiring therapy, and the
circulating water maintains the pad at the setpoint temperature. The setpoint temperature (TP700 series only) can be
locked to prevent tampering.
CONNECTING THE PADS
TheMul•T•Pads®can be interconnected using Clik-Tite®connectors to provide therapy to more than one body site at
a time.
Introduction
Figure 1B: Localized Temperature
Therapy System with Multiple Pads.
Figure 1A: Localized
Temperature Therapy System
with Single Pad with the TP650
and TP700.

1-6 101515 REV C
Introduction
CATALOG DESCRIPTIONS
Catalog # Product Name
TP650 Classic Control Unit
TP700 Professional Control Unit
TP22B Mul•T•Pad®: 15"w x 22"l (38cm x 56cm)
All Polymer. 10 per carton
TP22C Mul•T•Pad®: 15"w x 22"l (38cm x 56cm)
Nonwoven fabric on one side, pliable polymer on the other side. 1 per carton
TP3E Mul•T•Pad®: 3"w x 23"l (8cm x 58cm)
Nonwoven fabric on one side, pliable polymer on the other side. 10 per carton
TP12E Mul•T•Pad®: 13"w x 18"l (33cm x 46cm)
Nonwoven fabric on one side, pliable polymer on the other side. 20 per carton
TP22E Mul•T•Pad®: 15"w x 22"l (38cm x 56cm)
Nonwoven fabric on one side, pliable polymer on the other side. 20 per carton
TP26E Mul•T•Pad®: 18"w x 26"l (46cm x 66cm)
Nonwoven fabric on one side, pliable polymer on the other side. 10 per carton
TP22G Mul•T•Pad®: 15"w x 22"l (38cm x 56cm)
Heavy Polymer, Reuseable. 10 per carton
TP650C Classic Control Unit with Colder®
TP700C Professional Control Unit with Colder®
TP612E Mul•T•Pad®: 13"w x 18"l (33cm x 46cm)
Nonwoven fabric on each side with Colder®. 10 per carton
TP622E Mul•T•Pad®: 15"w x 22"l (38cm x 56cm)
Nonwoven fabric on each side with Colder®. 10 per carton
TP626E Mul•T•Pad®: 18"w x 26"l (33cm x 46cm)
Nonwoven fabric on each side with Colder®. 10 per carton
To order any of these products contact your dealer or Stryker’s Customer Service Department at:
Telephone: [phone]
Or, visit our website at www.stryker.com

101515 REV C 1-7
INDICATIONS FOR USE
Localized temperature therapy is recommended in treating the following applications:
Orthopedic Conditions such as:
acute injuries, chronic pain, lower back pain, muscle spasm and strains
Skin Trauma such as:
abscesses, boils, bruises, burns and contusions
Other conditions such as:
chronic arthritis, neuritis, phlebitis, tendonitis and I.V infiltration, infection and localized pain.
Other applications only as prescribed.
OK for Use With:
•Non-acute traumatized tissue.
•Impaired mental status.
•Insensate body surface.
•O2therapy. However, if oxygen tent is in use, do not use pump inside tent.
CLINICAL CONTRAINDICATIONS
Heating contraindications are:
•Application to a body surface with compromised blood flow (Ischemia, area under pressure, arterial insufficiency).
•Application to a patient with an increased tendency to bleeding (aggravates potential for hemorrhage).
•Application to a body surface with possibility of malignancy (tissue metabolism is increased and therefore, the
growth potential of the malignant tissues).
•Treatment of hematoma within first 24-48 hours (potential for re-bleeding and hemorrhage).
•Recent sprain or fracture (acute inflammatory response).
•In combination with topical solutions whose toxicity may be affected by the application of heat.
•In combination with other heat sources.
Cooling contraindications are:
•Application to a body surface with compromised blood flow or hypersensitivity to cold (Ischemia, Reynauds
Syndrome).
Indications and Contraindications

1-8 101515 REV C
Features
PUMP FEATURES
Easy to Use
Keypad
See KEYPAD FEATURES on page 1-9 (TP600 series) and page 1-10 (TP700 series).
Attached hose 10 ft (305 cm) dual hose. Connectors allow pads to be connected to the pump (Figures 1A
and 1B, page 1-5).
Flow indicator Indicates no flow. Turns off heater if pump is tipped.
Warm/Cool
Delivery
Three setpoints on the TP600 series.
Four temperature setpoints on the TP700 series.
Therapy Cycles
(TP700 series
only)
Choose from 20-minute, 30-minute, or Continuous cycles.
On/Standby
Button
Indicates power is supplied to the unit.
Over Temp Safety
Thermostat
Limit thermostat shuts off heater if the high temperature limit is exceeded.
Self Check Automatic system check at startup.
Hose/cord
Management
Convenient and easy storage areas for hose and cord.
Comfortable
Handle Design
Designed for a more comfortable grip when moving the pump.
Dual Micro
Processor
Two electronic circuits, one over temperature sensing circuit.
Tethered Easy-
Open Cap
Prevents misplacing the cap. Only 1/4 of a turn is needed to remove or secure the cap.
Handle Vents The vents in the handle allow air flow to keep the motor and heater inside the unit cool.
Easy to Use Keypad
Hose Connections
Flow Indicator
Temperature
Setpoints for warm
or cool delivery
On/Standby Button
Tethered Easy-Open Cap
Hose storage
Cord storage
Comfortable Handle
Therapy Time Cycles
(TP700 series only)
Figure 2: T/Pump Features
Handle Vents

101515 REV C 1-9
Features
KEYPAD FEATURES TP600 SERIES
Indicator/
Warning Light
See the Troubleshooting section on page 1-15.
Water Flow
Check hoses and clamps for kinks or occlusions.
Water Level
Check water level.
Setpoints Press the button at the bottom of the setpoint indicator to
toggle through the three setpoints.
High Heat is 107°F (42°C).
Low Heat is 100°F (38°C).
Cooling is 50°F (10°C).
On/Standby
Button
Green indicates the unit is on.
Yellow indicates power is supplied to the unit but the unit
is not on.
Figure 3: TP600 Series Keypad

1-10 101515 REV C
Features
KEYPAD FEATURES TP700 SERIES
Indicator/
Warning Light
See the Troubleshooting section on page 1-15.
Water Flow
Check hoses or clamps for kinks or occlusions.
Water Level
Check water level.
Setpoints Press the button at the bottom of the setpoint indicator
to toggle through the four setpoints. Temperatures are
identified in °C and °F.
Setpoint Lock Prevents tampering.
Press and hold for 2 seconds to lock or unlock the
setpoint.
Therapy
Cycles
Continuous cycle, 30-minute cycle or 20-minute cycle.
On/Standby
Button
Green indicates the unit is on.
Yellow indicates power is supplied to the unit but the unit
is not on.
Figure 4: TP700 Series Keypad

101515 REV C 1-11
Operating Instructions
CLIK-TITE CONNECTORS
5A 5B
5C 5D
6B 6C
Figure 5: Clik-Tite®Connectors
The TP600 & 700 Series T/Pump is supplied with Clik-Tite®connectors.
To connect and disconnect Clik-Tite®connectors from hose to pad:
1. Insert male fittings into female fittings with a twisting motion
(Figures 5A and 5B).
2. When fittings are fully inserted, snap locking ring into place
(Figures 5C and 5D).
3. To disconnect, reverse the procedure.
4. To open or close the hose pinch clamps:
•Open the clamp by pushing the serrated end (Figure 6B).
•Close the clamp by pressing the clamp together (Figure 6C).
Note: Refer to Figure 1B on page 1-5 when connecting multiple pads.

1-12 101515 REV C
Operating Instructions
COLDER
To connect and disconnect Colder®to a pad:
1. Push the male coupling onto the female coupling. When you hear an audible click, the connectors are joined
(Figure 6A).
2. To open or close the hose pinch clamps:
•Open the clamp by pushing the serrated end (Figure 6B).
•Close the clamp by pressing the clamp together (Figure 6C).
3. To disconnect, press down on the thumb tab of the female coupling. The couplings will partially disconnect.
4. Pull the male coupling out fully to disconnect (Figure 6D).
Figure 6: Colder

101515 REV C 1-13
Operating Instructions
WARNING
• Pump must be filled with water prior to operation.
• To avoid the risk of shock, unplug the unit before filling the reservoir.
1. Before filling the pump, attach a pad to the connector hose. Make sure that
there are no kinks in the hose or pad. Open the hose clamps.
2. Open the fill cap on top of the pump.
3. To fill for cooling:
a. Fill with cold water to the Cooling water line.
b. Fill with ice to the full capacity of the reservoir.
4. To fill for heating, fill with room temperature
water to the Heating water line.
5. Plug the T/Pump into a properly grounded Hospital Grade receptacle.
6. Press the On/Standby button. The light next to the selected temperature begins to flash.
7. Use the keypad to set the temperature as directed by the prescriber. For the TP700 only, after setting the
temperature, press and hold the lock Temperature Setpoint button for 2 seconds to lock the setpoint.
Note: If you toggle past the desired setpoint, keep toggling to start at the beginning of
the setpoint column. The selected water temperature will be reached in approximately
15 minutes and the light next to the selected temperature becomes steady.
8. Check the water level. If it drops below the operating level, add water.
9. ApplytheMul•T•Padtothepatientasprescribed.FollowtheMul•T•Padinstructions.
10. Position the pump at or above the level of the pad.
Note: If the pump is placed below the pad(s), water will drain into the pump when it is shut off. If
the pump has been overfilled or if multiple pads are connected, excess water can leak.
11. When using for cooling, the ice will eventually melt and the setpoint will start flashing. Press on/
standby button so the standby light is lit. Unplug pump from power receptacle. Open fill cap and
invert pump over sink to drain water. Refer back to step #3 and follow through procedure.
SHUTDOWN PROCEDURE
1. Press the On/Standby button so that the Standby light is lit.
2. Unplug the T/Pump.
3. Close all hose clamps.
4. Disconnect pad(s) from pump.
Note: To prevent water spillage, always disconnect pad from pump with connectors raised above the level of the
pad and pump.
5. Coil the hose, and attach the Clik-Tite®connectors together on the hose (See Figure 5, page 1-11), where
applicable.
6. Secure the hose to the T/Pump using the tube set strap.
7. Wrap the power cord around the unit.
START-UP PROCEDURE

1-14 101515 REV C
Therapy Cycles
THERAPY CYCLES, PROFESSIONAL ONLY
1. Turn the unit on, set the temperature setpoint. The unit will start to heat up. Select warming period for 20 (or
30) minute cycle, LED should be solid, and the selected temperature LED is flashing.
2. Once the T/Pump reaches the desired temperature, the Warming LED (Red) flashes with a short audible beep.
This is to let the operator/user know the unit is at temperature and the timed therapy is starting.
3. Once the 20 (or 30) minute period is up, the heater and pump shuts off. This stops any flow to the pad. The
Setpoint and Therapy time LED’s will be blinking during the off Time period.
4. Once the Off Time period is up, the pump and heater will restart. Time Therapy LED goes solid, and the
Setpoint LED is flashing. Once the Setpoint is reached the Red LED flashes with a short audible beep to let the
operator/user know the next therapy cycle has started.

101515 REV C 1-15
Troubleshooting
Problem Possible Cause Remedy
T/Pump will not turn on. The electrical cord is not plugged into
a properly grounded Hospital Grade
receptacle.
Insert the plug fully into the properly
grounded Hospital Grade receptacle.
T/Pump will not pump. Water level is low or reservoir is empty. Refill with room temperature water to
proper level.
Flow indicator light is on. Water flow to pad or hose is restricted.
Clamp is closed.
Water level is low or reservoir is empty.
T/Pump is filled with water that is too hot.
Straighten the hose.
Open the clamp.
Refill with room temperature water to
proper level.
Refill with room temperature water to
proper level.
Warning indicator &
Audible alarm (Flash /
Beep).
A High Heat (107°F / 42°C) or Cooling
Setpoint was selected
(50°F / 10°C).
Loss of power while unit was in a Therapy
mode. (Possible Power Fail.)
Unit is running after a 20- or 30- minute
“Off “therapy cycle period, has reached
the desired Setpoint, and is now timing
the 20- or 30- minute On cycle period
(TP700 only).
The unit just went into, or came out of
Lock mode (TP700 only).
Indication only: A Setpoint outside body
temperature range is selected.
Insert the plug fully into the receptacle,
place the unit into Standby mode, then
unplug the
T/Pump. If power is removed while unit
is in On-Mode, the Power Fail alarm will
beep for approximately 10 minutes.
Indication only to indicate an “On”
Therapy cycle period is timing.
Indication only.

1-16 101515 REV C
Troubleshooting
Problem Possible Cause Remedy
Warning indicator on with
unit in Standby mode.
Unit shut down in an over temperature
condition.
Empty the reservoir and refill with room
temperature water.
Make sure all clamps are open.
Press the On/Standby button.
Verify flow through the pad.
The Warning light will turn off within 5
minutes.
Flow indicator and Standby
indicator are on with
T/Pump not pumping.
Unit detected a Flow warning for more
than 5 minutes, thus goes to standby.
Reference “Flow indicator light is on”
above.
Correct the problem, and press the On/
Standby to put the unit back into Run
mode.
Temperature Setpoint light
blinking.
Unit is warming up to the selected
setpoint.
Unit is in Cooling mode, for longer than
40 minutes.
Indication only.
Follow the shutdown procedure. Drain the
water in reservoir to ice fill level, and refill
with ice. Follow the start-up procedure.

101515 REV C 1-17
Troubleshooting
Problem Possible Cause Remedy
Both the Temperature and
Therapy Cycle Setpoint lights
are blinking (TP700 Only).
Unit is in “Off” Therapy cycle time. Indication only.
T/Pump will not heat. Reservoir is empty.
Flow is blocked.
Refill with room temperature water to
proper level.
Reference “Flow indicator light is on”
above.
T/Pump will not cool. Reservoir is empty.
Flow is blocked.
Ice is depleted.
Refill with room temperature water to
proper level.
Reference “Flow indicator light is on”
above.
Drain excess water to Cooling water
line and fill remainder of reservoir with
ice.
Temperature or Therapy Time
buttons do not work (TP700
Only).
The buttons have been locked. Press and hold the lock button for two
seconds.
Water leaks from hose
connectors.
Damaged O-ring.
Locking ring on Clik–Tite®connector is
not snapped into place (See Figure 5 on
page 1-11)
Quick disconnect not seated properly.
Replace Clik–Tite®connector.
Snap Clik–Tite®connector shut.
Secure pad connection to pump (See
Colder on
page 1-12) Replace connectors or pad
if defective.

1-18 101515 REV C
Cleaning
STORAGE / CLEANING
Storage (Short term) Less than 1 day
1. Close the hose clamps.
2. Disconnect the pad.
3. Connect ends of the connector hoses together, where applicable.
4. Open the hose clamps.
5. Leave water in the reservoir.
6. Coil and fasten the hose using the tube set strap and wrap the power cord around the unit.
Storage (Long term)
1. Drain the pump. (See instructions below.)
2. Coil the hose, rather than folding it, to prevent hose kinks.
3. Fasten the hose using the tube set strap and wrap the power cord around the unit.
Draining
1. Disconnect the T/Pump from AC power.
2. Clamp the hose clamps.
3. Disconnect the pad or hoses from one another, keeping hoses at or above the level of the T/Pump.
4. Open the hose clamps.
5. Remove the fill cap and invert the T/Pump over a sink.
6. When all fluid has drained from the hoses and reservoir, replace the fill cap.
7. Connect the hoses together, where applicable.