Sunjoy 187020 User manual

WARNING:
● Keep all children and pets away from assembly area. Children and pets should be
supervised when they are in the area of the Gazebo construction.
● Keep assembly area at least 6 feet from any obstruction such as a fence, garage,
house, overhanging branches, laundry line, or electrical wires.
● Some parts may container sharp edges. When assembling and using this product,
basic safety precautions should always be followed to reduce the risk of personal
injury and damage to the product. Please read all instructions before assembly and
use
● Check all bolts for tightness before use, and periodically check and tighten bolts as
necessary.
● Gazebo is designed for wind speeds of up to 30 miles per hour. Customer should
disassemble the gazebos when there is a chance of wind speeds higher than 30
miles per hour.
● Please take down the gazebo during strong wind. The manufacturer or retailer is not
liable for any loss of the product or other items due to the failure to take down the
gazebo during strong wind.
Caltalina Gazebo
TV NO.:187020

Small connector A1 1
Big connector A2 1
Finial B1 1
Hook B2 1
Connector 1 C1 4
Connector 2 C2 4
Slide beam 1 D 4
Slide beam 2 E 4
Corner connector E1 8
Beam 1 F 4
Beam 2 G 2
Beam 3 H 2
Post 1 I 4
Post 2 J 4
Screen K 4
Small canopy L 1
Big canopy M 1
Mosquito netting N 1
Parts List

AA M5*15 Bolt 32 PCS
BB M5 Flat washer 48 PCS
CC M5*35 Bolt 16 PCS
Hardware Pack 1
W M5 Wrench 1 PC

Fig.1: Using bolt (AA) and flat washer (BB) to assemble the beam 1(F) to
the post 1 (I) or post 2 (J). Make sure the canopy holes face outside on
the beam 1 (F) when secure it.
Fig.2: Using bolt (CC) and flat washer (BB) to connect the screen (K) to the
post 1(I) or post 2 (J).
Fig.3: Using bolt (AA) and flat washer (BB) to connect the beam 3 (H) to
the post 1 (I) or post 2 (J). Make sure the canopy holes face outside on
the beam 3 (H) when secure it.
Fig.4: Using bolt (AA) and flat washer (BB) to connect beam 2 (G) to the
post 1 (I) or post 2 (J). Secure all bolts by using wrench (W).
GG M5*15 Screw 16 PCS
DD Ф6*180 Stake 16 PCS
BB M5 Flat washer 24PCS
CC M5*35 Bolt 4 PCS
EE M5 Nut 4 PCS
Hardware Pack 2

Fig.5: Insert the connector 2 (C2) into the big connector (A2) and attach the hook (B2) to the big
connector (A2).
Fig.6: Insert the slide beam 1 (D) and slide beam 2 (E) into the connector 2 (C2).
Fig.7: Insert the slide beam 2 (E) into the corner connector (E1) as arrow shows and connect them
by using screw (GG) and flat washer (BB). Use the same way to insert the slide beam 1 (D) into
the corner connector (E1).
Fig.8: Insert the corner connector (E1) to the post 1 (I) and post 2 (J). And attach the big canopy (M)
to the top.
Fig.9: Insert the connector 1 (C1) into the small connector (A1) and attach the small canopy (L).
Assemble the finial (B1) to the small connector (A1).
Fig.10: Assemble the connector 1 (C1) to the connector 2 (C2) and connect them by using bolt (CC),
flat washer (BB) and nut (EE). Attach the small canopy (L) on the small top completely. Then
attach the hooks of the big canopy (M) to the beams.
Fig.11: Secure the whole gazebo on the ground by using stake (DD).

FF Ring 48 PCS
Fig.12: Using the ring to attach the mosquito netting (N)
to the beams (H,F&G).
Hardware Pack 3