Sunjoy L-GZ025PCO-7A User manual

Thrshd Tivering Gazebo 10x12''
Style# L-GZ025PCO-7A
Tc# 14232049
>>assembly instructions

Warning
1. When assembling and using this product, basic safety precautions should always be followed to reduce the risk of personal injury and damage to equipment. Please
read all instructions before assembly and use.
2. Some parts may contain sharp edges, wear protective gloves if necessary. At least four or more people are recommended for safe assembly.
3. Keep all children and pets away from assembly area.
4. Begin assembly not less than 6 feet from any obstruction such as fence, garage, house, overhanging branches, laundry line or electrical wires.
5. Install on level ground. This gazebo cannot be permanently staked or attached to concrete floor or platform. This gazebo is intended for decorative and sunshade
purposes only and is not meant to withstand inclement weather including high winds, rain and snow. Gazebo fabric is water resistant, not water proof and may leak
during exposure to precipitation.
6. Check all nuts and bolts for tightness before and during usage.
7. Keep all flame and heat sources away from this gazebo fabric. This gazebo is made with fabric that meets CPAI-84 specifications for flame resistance. It is not fire proof.
The fabric will burn if left in continuous contact with any flame source. The application of any foreign substance to the gazebo fabric may render the flame-resistant
properties ineffective.
Tools needed
>>assembly instructions

Hardware pack 1
(AA) x 16 1/4"-20*0.6
Bolt
（Z）x1 1/4"-20
Wrench
(BB) x 52 Φ1/4"
Flat washer
(CC) x 28 1/4"-20*0.75
Bolt
Hardware pack 3
(AA) x 8 1/4"-20*0.6
Blot
(BB) x56 Φ1/4"
Flat washer
(CC) x 48 1/4"-20*0.75
Bolt
Hardware pack2
(EE) x 8 1/4"-20*0.6
Bolt
(AA) x 2 1/4"-20*0.6
Bolt
(DD) x 16 Φ5/16"*7
Peg
Spare Hardware Pack
(BB) x 4 Φ1/4"
Flat washer
(CC) x 2 1/4"-20*0.75
Bolt
(GG) x 5 plastic ring x 2 snap link

>>assembly instructions
Part List
A1 Long screen 1 2
A2 Long screen 2 2
B1 Short screen 1 2
B2 Short screen 2 2
C Connection of Middle Girder 4
D Connection of Tilt Girder 1 2
E Connection of Tilt Girder 2 2
F Long Slide way 4
G Short Slide way 4
H1 Top Tilt Girder 4
H2 Long Girder 2
H3 Short Girder 2
I1 Long Tube for Top Frame 2
I2 Short Tube for Top Frame 2
J1 Corner block for big roof 1 2
J2 Conner block for big roof 2 2
K Small top Girder 4
L Hook 1
M connection for small top 1
N Post 4
O Post base 4
P Post cover 4
Q Baffle 4
R Large canopy 1
S Small canopy 1
T Mosquito Netting 1
GG Wheel 52
HH Plastic plug 16
GGHH

Fig.1：
Insert Long screen (A2) into Long screen (A1)
Insert Short screen (B2) into Short screen (B1),
tighten with bolt (CC) and (EE), Flat washer (BB).
Fig.5:
Attach Long Slide way (F) / Short Slide way (G) to corner
of the assembly Long screen (A1) & Short screen 1 (B1).
Repeat same process on Long screen (A2) & Short
screen (B2). Tighten with Bolt (AA), Flat washer (BB).
Fig.2:
Attach Connection of Tilt Girder (D) & (E) to assembled screens in Fig 1
tighten with Bolt (CC) and Flat washer (BB).
>>assembly instructions
Fig.3：
Attach Connection of Middle Girder (C) to middle
of screen with bolt (CC) and Flat washer (BB).
Fig.4：
Cover the end of the Long Slide way (F) /
Short Slide way (G) in the middle side with
plastic plug.

>>assembly instructions
Fig.6: Insert Long Tube for Top Frame (I1) & Short Tube for Top
Frame (I2) into Conner block for big top 1 (J1)& Conner block for
big top 2 (J2)
Fig6-1:
Insert Top Tilt Girder (H1) into Conner block for big top 1 (J1) & Conner block
for big top 2 (J2)
Fig.7:
Insert Top Tilt Girder (H1) into Connection of Tilt Girder (D). Fig.8: Insert Long Girder (H2)/ Short Girder (H3) into
Tubes (I1) & (I2).

>>assembly instructions
Fig.11:
Attach Small top Girder (K) onto Corner block for big roof 1 /
Corner block for big roof 2 (J1) / (J2), spread the large canopy (R)
completely.
Hang the pothooks of the large canopy into the holes on the
panels.
Fig.10:
Attach the hook (L) onto the connection for small top (M).
Insert the Small top Girder (K) into the connection for small top (M),
Place the small canopy (S) on the small top, spread completely.
Fig.9:
Insert Long Girder (H2) Short Girder (H3) into Connection of Middle
Girder (C). Then place large canopy (R) onto the big top, but do not
spread it.

>>assembly instructions
Fig.12:
Attach Post base (O) to Post (N),tighten with Bolt (AA),
Flat washer (BB).
Fig.13:
Attach cover (P) onto Post (N), tighten with Bolt (CC) and Flat washer
(BB).

Fig.15: Hang the Mosquito Netting (T) onto the Slide Ways (F)&(G)
by using Plastic ring (GG), then cover with plastic plug (HH).
>>assembly instructions
Fig.16:Attach Baffle (Q) onto the Post cover (P),tighten with
Bolt (AA) and Flat washer (BB)
Fig.14:Attach the posts to the assembled top, tighten with Bolt (CC)
and Flat washer (BB).
Fig.17: Secure the assembled gazebo on the ground by using pegs (DD).

Care & Maintenance
Our iron / steel components for garden accessories and furniture are treated with rust inhibiting paint that protects it from rusting. However, due to
the nature of iron / steel, surface oxidation (rusting) will occur once these protective coatings are scratched. This is a natural process and is not a
defect! To minimize this condition, we recommend care to be taken when assembling & handling the product to prevent the paint from being
scratching. Should any scratching or damage occur, we recommend immediate touch-up with rust inhibiting paint. Surface rust can also be easily
removed with a very light application of common cooking oil. If surface oxidation (rusting) occurs and no measure is taken to prevent this, the
oxidation may start dripping on to deck or patio and cause damaging stains, which may be difficult to remove. This can be prevented if measure is
taken to keep the product from oxidizing.
Limited warranty
This Limited warranty is extended to the original purchaser and applies to defects in materials and workmanship of your item provided the item is
maintained with care and used only for personal, residential purposes.
The item is warranted to be free from defects in material or workmanship for a period of 6 months. We don’t reimburse for transportation or delivery
costs, or compensate the individual or any outside party for assembling or disassembling the product.
Exclusions
Items used for commercial, contract, or other non-residential purposes, or items damaged due to acts of nature, vandalism, misuse, or improper
assembly are not covered. Corrosion or rusting of hardware is not covered. Proof of purchase (dated register receipt) is required for warranty claims.
Warranty is to the original purchaser and is non-transferable. Any replacement of warranted items will be in the original style and color, or a similar
style and color if the original is unavailable or has been discontinued. As some states do not allow exclusions or limitations on an implied warranty,
the above exclusions and limitations may not apply. This warranty gives you specific rights, and you may also have other rights, which vary from state to state.