Sunny SF-T722021 User manual

Interactive Slim Treadmill with Bluetooth
SF-T722021
USER MANUAL
IMPORTANT! Please retain owner’s manual for maintenance and adjustment instructions. Your satisfaction is
very important to us, PLEASE DO NOT RETURN UNTIL YOU HAVE CONTACTED US:
[email protected] or 1-877-90SUNNY (877-907-8669).

1
IMPORTANT SAFETY INSTRUCTIONS
When using electrical appliances, basic precautions should always be followed, including the
following:
Read all instructions before using this treadmill.
DANGER – To reduce the risk of electric shock:
1. Always unplug this appliance from the electrical outlet immediately after using and before
cleaning.
WARNING – To reduce the risk of burns, fire, electric shock, or injury to persons:
1. The treadmill should never be left unattended when plugged in. Unplug from outlet when not in
use and before putting on or taking off parts.
2. Use this treadmill only for its intended use as described in this manual. Do not use attachments
not recommended by the manufacturer.
3. Never operate this treadmill if it has a damaged cord or plug, if it is not working properly, if it has
been dropped or damaged, or dropped into water. Return this treadmill to a service center for
examination and repair.
4. Keep the cord away from heated surfaces.
5. Never operate the treadmill with the air openings blocked. Keep the air openings free of lint, hair,
and alike items.
6. Never drop or insert any object into any opening.
7. Do not use outdoors.
8. Do not operate where aerosol (spray) products are being used or where oxygen is being
administered.
9. To disconnect, turn the treadmill off, then remove the plug from the outlet.
10. Connect this treadmill to a properly grounded outlet only. See grounding instructions.
11. This appliance is not intended for use by persons with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for their safety. Keep children
under the age of 13 away from this machine.
12. Household use only.
13. REMOVE CONTROL BOX (OR KEY, OR SAFETY PIN, AS APPLICABLE) WHEN NOT IN USE,
AND STORE OUT OF REACH OF CHILDREN.
14. Do not carry this appliance by supply cord or use cord as a handle.
CAUTION:
To avoid injury, use extreme caution when stepping onto or off of a moving belt. Read instruction
manual before using.
SAVE THESE INSTRUCTIONS

2
IMPORTANT SAFETY INFORMATION
We thank you for choosing our product. To ensure your safety and health, please use this equipment
correctly. It is important to read this entire manual before assembling and using the equipment. Safe
and effective use can only be achieved if the equipment is assembled, maintained and used properly.
It is your responsibility to ensure that all users of the equipment are informed of all warnings and
precautions.
1. Before starting any exercise program, you should consult your physician to determine if you have
any medical or physical conditions that could put your health and safety at risk or prevent you from
using the equipment properly. Your physician’s advice is essential if you are taking medication that
affects your heart rate, blood pressure, or cholesterol level.
2. Be aware of your body’s signals. Incorrect or excessive exercise can damage your health. Stop
exercising if you experience any of the following symptoms: pain, tightness in your chest, irregular
heartbeat, shortness of breath, lightheadedness, dizziness, or feelings of nausea. If you do
experience any of these conditions, you should consult your physician before continuing with your
exercise program.
3. Keep children and pets away from the equipment. The equipment is designed for adult use only.
4. Use the equipment on a solid, flat level surface with a protective cover for your floor or carpet. To
ensure safety, the equipment should have at least 8 feet (240CM) of free space behind it and 2 feet
(60CM) on each side. Do not place the treadmill on any surface that blocks air openings. To protect
the floor or carpet from damage, place a mat under the treadmill.
5. Ensure that all nuts and bolts are securely tightened before using the equipment. The safety of the
equipment can only be maintained if it is regularly examined for damage and/or wear and tear.
6. Always use the equipment as indicated. If you find any defective components while assembling or
checking the equipment, or if you hear any unusual noises coming from the equipment during
exercise, discontinue use of the equipment immediately and do not use until the problem has been
rectified.
7. Wear suitable clothing while using the equipment. Avoid wearing loose clothing that may become
entangled in the equipment.
8. Do not place fingers or objects into the moving parts of the equipment.
9. The maximum weight capacity of this unit is 265 pounds (120 KG).
10.This equipment is not suitable for therapeutic use.
11. To avoid bodily injury and/or damage to the product or property, proper lifting and moving are
required.
12.Your product is intended for use in cool and dry conditions. You should avoid storage in extreme
cold, hot, or damp areas as this may lead to corrosion and other related problems.
13.This equipment is designed for indoor and home use only; it is not intended for commercial use!

3
6
IMPORTANT OPERATING INSTRUCTIONS
1. Insert the power plug directly into the socket.
2. Read the manual before operating the equipment.
3. Changes in speed do not occur immediately. Set your desired speed using the adjustment keys on
the main console. The speed will increase gradually.
4. While on the treadmill, move with caution as distractions may cause you to lose balance and stray
from walking in the center of the belt. This may result in serious injury.
5. This unit starts at a very low speed. To begin use, hold onto the handrails and stand on the side rails
while it starts up, then step onto the belt once it’s in motion.
6. Always hold the handrail when making changes in the settings.
7. A safety key is provided for emergency use. The machine will function only if the safety key is
inserted into the computer console. In case of emergency, remove the safety key to immediately
stop the belt and shut off the treadmill. The display screen will reset once the safety key is
reinserted.
8. The console control keys are precisely set and require very little finger pressure to use. To avoid
damaging these keys, do not use excessive pressure when operating these controls.
9. This equipment is designed for adult use only! Children should not be allowed to use or play near
this equipment. When present, children should always be supervised by an adult.
10. Women who are pregnant or nursing should consult a physician before attempting to begin any
exercise program.
11. Always stay hydrated during and after exercise.
IMPORTANT NOTE:
The running belt must be lubricated before the first use! Please see Page 9 for instructions on how
to properly apply lubricant.

4
PRE-ASSEMBLY CHECK LIST
Before you start to assemble, please make sure all parts are included.
No.
Description
Spec.
Qty.
A
Treadmill
1
C24
Safety Key
1
D12
Power Wire
1
A09
Bottle Holder
1
B
Lubricant Oil
1
C
Manual
1
D
Thank You Card
1
E
Hardware Package
1

5
HARDWARE PACKAGE
Ordering Replacement Parts (U.S. and Canadian Customers only)
Please provide the following information in order for us to accurately identify the part(s) needed:
The model number (found on cover of manual)
The product name (found on cover of manual)
The part number found on the “EXPLODED DIAGRAM” and “PARTS LIST” (found near the end
of the manual)
Please contact us at [email protected] or 1-877-90SUNNY (877-907-8669).

6
ASSEMBLY INSTRUCTIONS
We value your experience using Sunny Health and Fitness products. For assistance with parts or
troubleshooting, please contact us at [email protected] or 1-877-90SUNNY
(877-907-8669).
STEP 1:
Open the carton box and remove contents.
Place the Main Frame (No. A) on level
ground, ensure that you have a work area
that is clean and has adequate space.
STEP 2:
Lift the Console (No. D01) along with Left &
Right Upright Tubes (No. A07 &No. A08)
upward (in the direction specified by the
arrows on the diagram to the left).

7
We value your experience using Sunny Health and Fitness products. For assistance with parts or
troubleshooting, please contact us at [email protected] or 1-877-90SUNNY
(877-907-8669).
STEP 4:
Turn the Left &Right Handlebar Foam (No.
C05 &C06) clockwise, and then attach
Console (No. D01) by using 2 Bolts (No.
E10) and 2 Flat Washers (No. E27). Secure
by using Allen Wrench (No. B01).
STEP 3:
Support the Left &Right Upright Tubes
(No. A07 &No. A08) with your hands to
prevent them from falling.
Attach the Left &Right Upright Tubes (No.
A07 &No. A08) to the Left &Right Side
Tube Assembly (No. A01 &No. A02) by
using 2 Bolts (No. E34). Secure by using
Allen Wrench (No. B01).

8
We value your experience using Sunny Health and Fitness products. For assistance with parts or
troubleshooting, please contact us at [e-mail] or 1-877-90SUNNY
(877-907-8669).
STEP 6:
Insert the pin end of Safety Key (No. C24) into
the Console (No. D01).
STEP 5:
Adjust the Panel Top Cover (No. C03) to the
angle you feel comfortable.
Attach the Bottle Holder (No. A09) to the
Right Upright Tubes (No. A08) by using 2
Bolts (No. E17). Secure by using Spanner
w/ Screw Driver (No. B10).
IMPORTANT NOTE!
You will need to lubricate your
treadmill before the first use.
See Page 9.

9
LUBRICATING THE TREADMILL
IMPORTANT NOTE:
You will need to lubricate your treadmill before the first use.
RUNNING BELTS & TREADMILL LUBRICANT:
Lubricating the Running Board (No. D11) and Running Belt (No. C17) is essential as the friction
affects the life span and operations of the treadmill. Inspect the Running Belt (No. C17) and Running
Board (No. D11) regularly. If you find any wear on the Running Board (No. D11), please contact us at:
[email protected].
WARNING: Always unplug the treadmill from the electrical outlet before cleaning, lubricating, or
repairing the unit.
HOW TO LUBRICATE:
1. Raise the Running Belt (No. C17) up on one side and apply lubricant to the Running Board (No.
D11). Use a rag to thoroughly wipe the lubricant over the Running Board (No. D11). Repeat this
process for the other side.
2. The moving parts should turn freely and quietly. Abnormal moving parts will affect the safety of the
equipment. Inspect and tighten bolts regularly.
3. To better maintain the treadmill and prolong its lifespan, it is suggested that maintenance be done
on a regular basis.
4. DO NOT LOOSEN OR MAKE ANY ADJUSTMENTS TO THE RUNNING BELT WHILE APPLYING
LUBRICANT. A loose Running Belt (No. C17) will result in the runner sliding off during use, while
too tight of a Running Belt (No. C17) will negatively affect the motor’s performance and create
more friction between the roller and Running Belt (No. C17). The most suitable tightness for the
Running Belt (No. C17) is when it is pulled out 50-75mm from the Running Board (No. D11).
The following time table is recommended:
Light user (less than 3 hours/ week) every six months
Medium user (3-5 hours/ week) every three months
Heavy user (more than 5 hours/ week) every two months

10
HOW TO MOVE THE MACHINE
Hold the treadmill at position “E” with your hand. Lift up the treadmill and then
you can move the treadmill to any place.

11
HOW TO ADJUST THE BALANCE
When the height of each pad or because of individual machine placed on the ground is not even,
you need to adjust the Adjustable Knob（No. C26）to level the machine on the ground.
Adjustment method: First, place the machine as shown in above, use Spanner w/ Screw
Driver (No. B10), and adjust the Adjustable Knob（No. C26）clockwise to raise the footpad, and
counterclockwise to lower the footpad. When you have finished adjusting the base leveler,
re-tighten the Nut (No. E04) by turning it clockwise using Spanner w/ Screw Driver (No. B10). If
required, repeat this process to adjust the remaining base levelers.

12
MAINTENANCE & CARE
General cleaning will help prolong the life and improve performance of your treadmill. Keep the unit
clean and maintained by dusting the components on a regular basis. Cleaning two exposed sides of
the Running Belt (No. C17) will prevent dust from accumulating underneath. Keep your running
shoes clean so that dirt from your shoes does not wear out the Running Board (No. D11) and
Running Belt (No. C17). Clean the surface of the Running Belt (No. C17) with a clean damp cloth.
To better maintain the treadmill and prolong its life, it is suggested that the treadmill be powered off for
10 minutes every 2 hours and fully powered off whenever not in use.
CENTERING THE RUNNING BELT:
Place the treadmill on level ground and set it at 3-5MPH to check if the Running Belt (No. C17) drifts
from the center.
If the Running Belt (No. C17) moves to
the right, turn the right adjusting bolt ¼
turn clockwise, then turn the left
adjusting bolt ¼ turn counter-clockwise.
If the Running Belt (No. C17) does not
move, repeat this step until it centers.
Refer to Figure A.
If the Running Belt (No. C17) moves to
the left, turn the left adjusting bolt ¼turn
clockwise, then turn the right adjusting
bolt ¼ turn counter-clockwise. If the
Running Belt (No. C17) does not move,
repeat this step until it centers. Refer to
Figure B.
Over time, the Running Belt (No. C17)
will loosen. To tighten the Running Belt
(No. C17), turn the left & right adjusting
bolts one full turn clockwise, check the
tension of the Running Belt (No. C17).
Continue this process until Running
Belt (No. C17) is at the correct tension.
Make sure to adjust both sides equally
to ensure correct belt alignment. Refer
to Figure C.

13
IMPORTANT ELECTRICAL INFORMATION
WARNING: This treadmill requires a power source of 10 amps (100-120V) in order to properly
operate. For your safety, as well as the safety of others, please verify that the power source is correct
before plugging in the equipment. Any power source above or below this level could cause significant
damage to the equipment and/or user.
GROUNDING METHODS:
This product must be grounded. Grounding provides a path of the least resistance for electrical current
to reduce the risk of electric shock. The plug must be plugged into an appropriate outlet that is properly
installed and grounded in accordance with all local codes and ordinances. Ensure that the product is
connected to an outlet which contains the same configuration as the plug. Do not use an adapter for
this product.
This product is for use on a nominal 100-120V circuit and has a grounding plug that looks like the plug
illustrated in sketch A.
DANGER:
Improper connection of the equipment can result in risk of electric shock. Check with a qualified
electrician or serviceman if you are unsure whether the product has been properly grounded. Do not
modify the plug provided with this product. If it will not fit the outlet, have a proper outlet installed by a
qualified electrician.
WARNING!
1. NEVER use a ground fault circuit interrupt (GFCI) wall outlet with this treadmill. Route the power
cord away from all moving parts of the treadmill, including the elevation mechanism and
transportation wheels.
2. NEVER operate the treadmill using a generator or UPS power supply.
3. NEVER remove any cover on the treadmill without first disconnecting power cord.
4. NEVER expose the treadmill to rain or moisture. This treadmill is not designed for outdoor use or
use in any high humidity environment.
GROUNDING METHOD

14
THE DISPLAY CONSOLE
QUICK START:
1. Insert the pin end of the Safety Key (No. C24) into the Console (No. D01).
2. Press the START button, and the system will automatically display a 3 seconds countdown. Once
the countdown reaches zero, the Running Belt (No. C17) will start at the initial default speed of
0.6 MPH.
3. To adjust the speed, you can use the SPEED +/- BUTTONS or QUICK SPEED BUTTONS 3, 4, ... &
8 MPH.
*NOTE: The maximum speed on this treadmill is 9.0MPH.
CONTROL FUNCTIONS:
1. Press the
Speed Button to reduce the running speed.
2. Press the
Speed Button to increase the running speed.
3. Pressing a
Quick Speed Button will adjust the speed to the corresponding speed indicated (3,
4, ... or 8 MPH).
4. Pressing the Stop Button will stop the running belt of the treadmill.
5. Holding the Pulse Sensors located on the handles with both hands for 5 seconds will calculate and
display the runner’s heartbeats per minute (BPM) on the console display screen.

15
WINDOW DISPLAY:
SPEED/ PULSE: The speed range is 0.6-9 MPH. 0.6MPH is the default running speed.
When the runner holds both hands on the pulse sensors (located on the handles), the system will
calculate the runner’s heartbeat and display it in this window. The pulse range is 50-200 beats/min.
NOTE: This data is just for reference and cannot be used for medical purposes.
TIME: Displays the time elapsed (0:00-99:59 MINS). If the time reaches 99:59, the treadmill will stop
smoothly and display “End” then automatically reset to 0:00 after 5 seconds.
When in Countdown Mode, it will count from the setting time to 0:00. When the clock reaches 0:00, the
treadmill will stop smoothly and display “End” then automatically reset itself after 5 seconds. Maximum
Countdown time is 99:00 minutes.
CALORIES/ DISTANCE: Displays the number of calories burned from 0 to 999 KCAL and the
distance traveled (0.0-99.9 MILE). When the count reaches 999 KCAL, it will reset and start back from
0. When in Countdown Mode, it will count down from the desired setting to 0. Once it reaches 0, the
treadmill will stop smoothly and display “End”, then automatically reset to the initial setting after 5
seconds. When the distance reaches 99.9 MILE, it will reset to 0.00 and begin counting again from 0.0.
When in Countdown Mode, it will count down from the setting data to 0.00. When it reaches 0.00, the
treadmill will stop smoothly and display “End” and automatically reset to the initial setting after 5
seconds.
When setting PROGRAMS, the speed is programmed in intervals; PROGRAMS are from
P01-P02-P03-…P14-P15-U1-U2-U3-FAT.
FUNCTION KEYS:
PROGRAM: Press the PROGRAM button to set your desired interval setting. Programs are displayed
as P01-P02-P03- …P14-P15-U1-U2-U3-FAT. and the various intervals are shown on the face of the
treadmill. P1-P15 are preset programs.
MODE: When stopped, press this button to select a Countdown mode.
15:00 MINS is the set Countdown for TIME.
1.0 Mile is the set Countdown for DISTANCE.
50 KCAL is the set Countdown for CALORIES.
When setting each Countdown Mode, you can press the speed +/– buttons to increase or decrease
from the set data. Press START to start the treadmill.
START: To start the treadmill, insert the pin end of the Safety Key (No. C24) into the Console (No.
D01) and then press the START button. This treadmill requires the Safety Key (No. C24) in order to
start. 0.6 MPH is the default start speed.
STOP: This button has functions of PAUSE and STOP. When in use, press this button once to PAUSE
your workout and the current workout data will still be shown. Press STOP again to terminate your
workout session completely and all data will be deleted and reset to the initial setting.
SPEED +/– BUTTONS: Press the +/- buttons to increase or decrease the speed in increments of 0.1
MPH. Pressing and holding either of these buttons for a duration of over ½ of a second will increase or
decrease the speed continually.
PROGRAMS
Initial
Default Value
Set Range
Display Range
TIME (MIN:SECOND)
0:00
15:00
5:00-99:00
0:00－99:59
SPEED (MPH)
0.0
0.6
0.6-9.0
0.6-9.0
DISTANCE (MILE)
0.00
1.00
0.50-99.9
0.00-99.9
PULSE (BPM)
P
N/A
N/A
50-200
CALORIE (KCAL)
0
50
10-999
0－999

16
3, 4, ... & 8 (QUICK SPEED BUTTONS): These buttons are preset to 3, 4, ... or 8 MPH speeds for
convenience.
LUBRICATION REMINDER:
Your treadmill needs lubrication maintenance every 188 Miles. The system will release a beeping
sound every 10 seconds and display an “OIL” icon on your display to remind you when it’s time.
Please read the LUBRICATING THE TREADMILL on Page 9 to learn the proper steps to lubricate your
treadmill. Apply the lubricant to the middle of the running board on both sides. After application, press
and hold the STOP button for 3 seconds to clear the “OIL” reminder.
INTERVAL PROGRAMS (P1-P15):
Press the PROGRAM button to select an interval setting. Programs are displayed as P1-P15. Select
the desired program, and the console will display a countdown starting from 10:00 MINS, press
SPEED +/- UP/DOWN BUTTONS if you wish to increase or decrease the exercise time. Press the
START button to start the interval program. The interval program is divided into 10 sections. Each
exercise time equals the setting time divided by 10. When the speed enters the next interval, the
treadmill will beep, and the speed will be changed according to the set interval. Press SPEED +/-
UP/DOWN BUTTONS to change the SPEED. After finishing one program, the system will beep and
display “End”. The machine will gradually come to a stop, then automatically reset to the initial setting
after 5 seconds.
TIME
PROG
TIME INTERVAL= setting time/10
1
2
3
4
5
6
7
8
9
10
P1
SPEED
1.8
1.8
3.1
3.1
4.3
4.3
3.1
3.1
1.8
1.8
P2
SPEED
6.2
1.8
3.1
4.3
1.8
4.3
3.1
4.3
3.1
1.8
P3
SPEED
1.8
1.8
3.1
4.3
4.3
5.6
4.3
3.1
3.1
0.6
P4
SPEED
1.8
3.1
1.8
4.3
0.6
3.1
4.3
3.1
1.8
0.6
P5
SPEED
3.1
3.1
3.1
4.3
5.6
6.8
5.6
4.3
4.3
3.1
P6
SPEED
1.8
3.1
5.6
6.8
4.3
7.5
5.6
6.8
3.1
1.8
P7
SPEED
1.8
4.3
5.6
6.8
5.6
5.6
5.6
4.3
3.1
3.1
P8
SPEED
3.1
3.1
5.6
5.6
6.8
3.1
6.8
6.8
3.1
1.8
P9
SPEED
1.2
3.1
3.1
5
5
2.5
3.7
1.8
1.8
1.2
P10
SPEED
1.2
1.8
2.5
3.7
4.3
3.1
3.1
3.7
4.3
1.8
P11
SPEED
1.8
2.5
3.1
5.6
3.1
5.6
3.1
3.1
3.7
1.8
P12
SPEED
0.6
1.2
1.8
6.2
4.3
4.3
6.2
3.1
2.5
1.8
P13
SPEED
0.6
0.6
1.8
3.1
3.1
3.1
5.6
1.8
0.6
0.6
P14
SPEED
1.8
2.5
4.3
1.8
2.5
3.7
1.8
2.5
3.1
1.8
P15
SPEED
1.2
1.8
3.1
3.1
4.3
4.3
4.3
3.7
2.5
1.8

17
SELF-DEFINE PROGRAM
Besides 15 inner installed programs, there are 3 user self-define programs: U1, U2, U3
1.User self-define program setting:
In the initial situation, press “PROG” continually till U1, U2, U3, and the “time” window glitter, show the
time 10:00, press “speed+”, “speed-” to set the running time; press “MODE” to set program data, set
the first interval time, press “speed+”, “speed-” or press speed shortcut button to set the speed; then
press “MODE” button to finish the first interval time and enter into the second interval time, until finish
10 interval time. The data will be kept until the next setting, the data will not be lost when powered off.
2. User self-define program starting:
When the machine is waiting for operation, press the “PROG” button continuely till U1, U2, U3, set the
running time then press “start” to start the machine.
3. User self-define program instruction:
Each program will be divided into 10 time sections, set the speed in each interval time, then press
“start” to run the machine.
BODY MASS INDEX:
Press the PROGRAM button until the window displays FAT to access Body Mass Index. Press MODE
to enter F-1, F-2, F-3, F-4, F-5.
F-1 SEX, F-2 AGE, F-3 HEIGHT, F-4 WEIGHT, F-5 is Body Mass Index
Press SPEED +/- BUTTONS to set F1-F4 (refer to the chart below). Once you have finished setting
F1-F4, press MODE. This will enter you into the set up for F-5 (Body Mass Index). To set F-5, grasp
the Pulse Sensors located on the handles with both hands and hold them for 3 seconds. The window
will display your body mass index. The Body Mass Index is used to test the relation between your
height and weight. It is only for reference not suitable for the medical use. The Body Mass Index is
suitable for both male and female.
NOTE: General Body Mass Index score is 20-25%
Underweight Below 19.0
Normal 19.0 – 25.0
Overweight 26.0 – 29.0
Obesity 30.0 – and above
BODY MASS INDEX (BMI) CHART:
F-1
Sex
01 Male
02 Female
F-2
Age
10---99
F-3
Height
10---240 CM (40---80 INCHES)
F-4
Weight
20---150 KG (44---330 LBS)
F-5
BMI
≤19
Underweight
BMI
=(20---25)
Normal Weight
BMI
=(26---29)
Overweight
BMI
≥30
Obesity

18
TREADMILL FUNCTIONS
SAFETY LOCK FUNCTION:
Removing the Safety Key (No. C24) from the Console (No. D01) while the treadmill is running will
cause it to stop immediately. Once the treadmill reaches a full stop, the window display of the console
will show “- - -” and the speaker will beep 3 times. To start the treadmill again, insert the pin end of the
Safety Key (No. C24) into the Console (No. D01) and press the START button.
POWER SAVE FUNCTION:
When the treadmill has been inactive for 10 minutes, it will enter Power Saving Mode. While the
treadmill is in this mode, the window display of the Console (No. D01) will be turned off. To turn it back
on, press any button.
POWER ON:
Click the power switch to this symbol to turn on the treadmill.
POWER OFF:
Click the power switch to this symbol to turn the treadmill off at anytime. This includes during exercise.
SAFETY NOTE:
We recommend that you maintain a slow speed at the beginning of a session and hold the Left &
Right Handlebar Foam (No. C05 &C06) handrails until you have become familiar with the treadmill.
Insert the pin end of the Safety Key (No. C24) into the Console (No. D01) and attach the opposite
end (containing the safety clip on it) to your clothing before starting your workout. To end your workout,
press the STOP button or remove the Safety Key (No. C24) and the treadmill will stop immediately.

19
EXERCISE INSTRUCTIONS
GETTING STARTED:
Before starting any exercise program, you should consult your physician to determine if you have any
medical or physical conditions that could put your health and safety at risk or prevent you from using
the equipment properly.
Be aware of your body’s signals. Incorrect or excessive exercise can damage your health. Stop
exercising immediately if you experience any of the following symptoms: pain, tightness in your chest,
irregular heartbeat, shortness of breath, lightheadedness, dizziness, or feelings of nausea.
Get to know your treadmill. Before attempting to use the treadmill take some time to stand alongside
and familiarize yourself with the controls.
1. Once you get on, you can stand with your feet on the Side Rails (No. C18) and stabilize yourself by
holding onto the handrails.
2. Next, attach the clip end of the Safety Key (No. C24) to your clothes and insert the pin end of the
key into the Console (No. D01).
3. Press the START button to start the treadmill.
4. The treadmill will start at the system default setting speed of 0.6MPH. When you feel comfortable,
you may slowly increase this speed.
5. When you are finished with your exercise, press the STOP button to stop the treadmill or you can
remove the pin end of the Safety Key (No. C24) to stop the treadmill.
APP CONNECTION:
1. Scan the QR code below to download the SunnyFit app onto your mobile device.
2. If this is your first time using the SunnyFit app, follow the in-app instructions to register for your
free SunnyFit account and log in.
3. Ensure that the Bluetooth function is turned on from your mobile device.
4. To connect the equipment to the SunnyFit app:
a. From the “Workout” tab, press on the “Search” button to search for your equipment.
b. Once your equipment appears on the list, tap the “Select” button to confirm.
c. Note: If your equipment does not appear on the "Searching for Equipment" list, check the
EXERCISE COMPUTER on your equipment to ensure that it is not in sleep mode and your
phone's Bluetooth function is on, then tap "Retry" to search again.
d. Once your equipment shows up on the “Workout” tab as “Currently Selected”, your equipment is
now ready to display, track, and record your equipment’s workout stats on the app!
5. If you are unable to replicate these steps, or have any other issues with the SunnyFit app, please
contact SunnyFit support at su[email protected], or use the in-app “Contact Us” form to request
support (“Me” tab -> “Contact Us”).