Sunnydaze Decor AGR-348 User manual

CL381 02/2023
END TABLE CABINET WITH DRAWER
AGR-348
Carefully review assembly and care instructions before using this product. Save this document for future reference.

Thank you for choosing Sunnydaze Decor. We stand behind our brand and the quality of the items we sell.
Replacement parts or products will be sent at our discretion within the 1-year warranty period. Proof of purchase, with
the date of purchase as well as photos of the merchandise defect, must be provided. Photos are used to determine
the cause of defects and for future quality control. Register your warranty at https://tiny.cc/SunnydazeWarranty
If you have any questions, comments or concerns, feel free to contact us by phone at 833-982-1977, by email:
[e-mail], or via our contact us page at https://tiny.cc/SunnydazeContact
Purchase Date: / / Order/Customer Reference Number:
HELPFUL HINTS
Sunnydaze Decor advises reviewing this manual fully, and assembling the unit soon after purchase.
Check that all parts are accounted for and familiarize yourself with the assembly before beginning.

2-PERSON
ASSEMBLY
Page 1 / 11
SCAN THIS CODE
WITH YOUR
SMARTPHONE
TO VIEW OUR
ASSEMBLY VIDEO
Inspect packaging to ensure all
parts are accounted for before
disposing of packing materials.
Save the packing slip.

CL381 02/2023
INTRODUCTION
Instrucciones
Instructions


Read the manual carefully to ensure you fully understand
all use, care, assembly, and safety information.
Read this manual carefully and
follow the assembly instructions
in the order listed. Pay close
attention to assembly diagrams.
Regularly clean with a clean
microber cloth to prevent dust
accumulation.
Do not paint the unit.
Do not use abrasive materials or
cleaners to clean the furniture.
Indoor use only.
Do not expose the furniture to
heat or humidity.
When cleaning nearby the
furniture, do not allow contact
with water or cleaners as it may
deteriorate the furniture.
Do not allow metal components
to come in contact with water or
cleaners as it may cause rust and
staining.
Assemble on a soft, at, clean, and
dry surface.
Use a soft, protective barrier when
assembling the furniture.
TIP: Use the box carton as a
protective layer to separate and
protect the parts from scratches and
other damage during assembly.
Do not push or drag furniture as
doing so may damage the unit.
Only move furniture when it is empty.
Always ask for help when moving
furniture.
Avoid Accidents - Do not climb, sit
or stand on the furniture.
Do not allow children to play on or
inside the furniture.
Keep sharp objects away as they
may scratch or damage the unit.
Do not use the furniture as a writing
surface without a padded barrier.
NOTICE:
Manufacturer and seller expressly disclaim any and all liability from personal injury, property damage
or loss, whether direct or indirect, or incidental, resulting from the incorrect attachment, improper use,

Page 2 / 11

CL381 02/2023
  
AWood Dowel 30
BM4.5x28mm Pan Screw 22
CConnector 12
DHandle Set 2
EM3.5x30mm Flat Screw 8
FHinge 2
GCatch 1
HStrike 1
JM3x16mm Flat Screw 4
KM3.5x14mm Pan Screw 12
LTack 4
MM3.5x25mm Pan Screw 4
NM4.5x25mm Pan Screw 6
ODrawer Slide 2
PM4x8mm Bolt 2
QM3.5x14mm Flat Screw 6
YWall Anchor Kit 1
Z8x8mm Nail 16
COMPONENTS
(not included)
Phillips Screwdriver
Regular
Screwdriver
Rubber Mallet
Hammer
Power Drill,
6mm Drill Bit,
2mm Drill Bit
  
01 Top 1
02 Left Side Panel 1
03 Right Side Panel 1
04 Bottom Panel 1
05 Bottom Frame 1
06 Center Face Frame 1
07 Top Face Frame 1
08 Drawer Rail 2
09 Side Trim Board (L/R) 2
10 Front Trim Board 1
11 Door 1
12 Drawer Back 1
13 Backing Board 2
14 Divider 1
15 Drawer Face 1
16 Drawer Side (L/R) 2
17 Drawer Bottom 1
18 Left Stile 1
19 Right Stile 1
CHOKING HAZARD —
This item contains small
parts that can be swallowed.
Keep children and pets away
during assembly.
WARNING
Inspect packaging to ensure all
parts are accounted for before
disposing of packing materials.
Save the packing slip.
(only use for installing wall anchor kit)
Page 3 / 11

CL381 02/2023
IMPORTANT: Take care not to over-tighten screws as doing so may crack the wood or strip the screw hole, causing a weak connection and reduced stability.
ASSEMBLY
Carefully review all steps and fully understand assembly before beginning.
STEP 1
02: 1
03: 1
04: 1
05: 1
06: 1
07: 1
08: 2
A: 30
Locate and lay out
Left Side Panel (02),
Right Side Panel (03), Bottom Panel (04),
Bottom Frame (05), Center Face Frame (06),
Top Face Frame (07), and two Drawer Rails (08).
Install Wood Dowels (A) as noted below:
Left Side Panel (02), install ve Wood Dowels (A).
Right Side Panel (03), install ve Wood Dowels (A).
Bottom Panel (04), install four Wood Dowels (A).
Bottom Frame (05), install four Wood Dowels (A).
Center Face Frame (06), install four Wood Dowels (A).
Top Face Frame (07), install four Wood Dowels (A).
Drawer Rail (08), install two Wood Dowels (A). Repeat with the second drawer rail.
Set components aside, label if necessary.
STEP 2
C: 12
G: 1
J: 2
With the angled edge facing the inside of the panel, install six Connectors (C) into Left Side Panel (02), and six
Connectors (C) into Right Side Panel (03).
Identify the two indents on the edge of Bottom Panel (04), align the mounting holes in Catch (G) with the indents, and
rmly secure using two M3x16mm Flat Screws (J).
TIP: Install connectors by gently tapping them into
the designated holes using a rubber mallet.
Page 4 / 11

CL381 02/2023
STEP 3
18: 1
19: 1
B: 6
STEP 4
B: 4
M: 4
IMPORTANT: Ensure
the pre-drilled holes on
Bottom Frame (05) are on
the bottom, as indicated
in the diagrams.
IMPORTANT:
Ensure the stiles are installed in the correct direction,
as indicated in the diagrams.
Lay Side Panel (02)
on a at, clean surface.
Ensuring the catch on Bottom Panel (04) faces the top of the unit, align Bottom Panel (04) with the mounting holes
just above the bottom-most connector on the side panel. Loosely secure using two M4.5x28mm Pan Screws (B).
Align Bottom Frame (05), Center Face Frame (06), and Top Face Frame (07) with the mounting holes in the left stile.
Secure Bottom Frame (05) and Top Face Frame (07) using M3.5x25mm Pan Screws (M).
Align Side Panel (03) with the opposite side of the unit. With assistance, carefully ip the unit so Side Panel (03) is on
the at, clean surface. Then, secure components using the same hardware as noted for securing the rst side panel.
Identify the Top and Bottom of the Side Panels (02,03), Left Stile (18) and Right Stile (19); the bottom of the stiles will
have a larger gap between the mounting holes and the end of the panel.
Ensuring the tops and bottoms are on the same side, align Left Stile (18) with Left Side Panel (02) and secure using
three M4.5x28mm Pan Screws (B).
Ensuring the tops and bottoms are on the same side, align Right Stile (19) with Right Side Panel (03) and secure
using three M4.5x28mm Pan Screws (B).
Assistance
is recommended
for this step.
Page 5 / 11

CL381 02/2023
STEP 5
01: 1
09: 2
B: 4
N: 6
STEP 6
10: 1
B: 2
Align Front Trim Board (10) with the bottom, front of the unit. Have an assistant rmly hold the trim board in place to
ensure it remains ush while hardware is secured. Secure the trim board to the bottom frame using two M4.5x28mm
Pan Screws (B).
Place Top (01) on a at, clean surface. Align the assembled components with the top and secure using six M4.5x25mm
Pan Screws (N).
Align two Side Trim Boards (09) with the bottom of the unit, as shown. Have an assistant rmly hold the trim boards in
place to ensure they remain ush with the unit while hardware is secured. From the inside of the side panels, secure
each trim board using two M4.5x28mm Pan Screws (B).
Assistance is recommended for this step.
Assistance is recommended for this step.
Page 6 / 11

CL381 02/2023
Front
Back
STEP 7
B: 6
STEP 8
O: 2
Q: 6
IMPORTANT:
The arrow on the drawer slide must face the
front of the cabinet.
Ensure the drawer slide remains centered on
the drawer rail; if the slides are not centered,
the drawer will be crooked.
IMPORTANT:
Ensure the drawer rails are installed in the correct direction,
as indicated in the diagrams.
Identify the two indents on Drawer Rails (08), the indent with the shortest distance from the edge of the rail must be
installed toward the front of the cabinet.
Align Drawer Rails (08) with the side panels and secure each rail using three M4.5x28mm Pan Screws (B).
Push the front of one Drawer Slide (O) backward. Align the 3rd hole from the front with the indent on the front side of
the drawer rail. Fasten the front of the drawer slide using one M3.5x14mm Flat Screw (Q).
Push the drawer slide forward to expose the holes on the back of the drawer slide, the indent will align with the 7th
circular hole from the back. Ensuring the slide is centered on the rail, secure the 7th and 3rd hole (from the back)
using two M3.5x14mm Flat Screws (Q).
Repeat this step to secure the remaining drawer slide.
Page 7 / 11

CL381 02/2023
x3
Back
ADJUSTING HINGE
x3
STEP 9
11: 1
D: 1
F: 2
H: 1
J: 2
K: 6
IMPORTANT: Ensure the door
is properly aligned before fully
securing any screws.
Assistance required for this step.
IMPORTANT:
Note the direction of the mounting holes on the hinges and install as
shown in the diagram.
Do not fully secure Screws (K) until after the door is properly aligned

STEP 10
K: 6
Align two Hinges (F) with the indents on the front of Door (11) and mostly, but not fully, secure using six M3.5x14mm
Pan Screws (K). Do not fully tighten screws until the door is properly aligned during the next step.
Ensuring the handle plate and ring remain straight, rmly secure Handle Set (D) to the door, as shown.
Turn the door over and secure Strike (H) using two M3x16mm Flat Screws (J).
With assistance to hold the door in place, align the top hinge with the indents on the left stile. Loosely secure each
hinge to the stile using three M3.5x14mm Pan Screws (K).
After ensuring the door is properly aligned, nish tightening all screws.
Page 8 / 11

CL381 02/2023
STEP 11
13: 2
14: 1
Z: 16
STEP 12
12: 1
15: 1
16: 2
17: 1
D: 1
E: 8
Place two Backing Boards (13) on the back of the unit and slide Divider (14) between them.
Ensure the backing boards are snug beneath the lip of the top and the lips of the side panels. Then, secure the
backing board using sixteen 8x8mm Nails (Z).
Ensuring the inside grooves align, secure two Drawer Sides (16) to Drawer Face (15) using four M3.5x30mm Flat
Screws (E).
With the nished side facing upward, slide Drawer Bottom (17) into the grooves, as shown.
Secure Drawer Back (12) to the drawer sides using four M3.5x30mm Flat Screws (E).
Ensuring the handle and handle plate remain straight, install one Handle Set (D), as shown.
Page 9 / 11

CL381 02/2023
M3.5x14mm
M3.5x25mm
Wall
Top
STEP 13
P: 2
L: 4
STEP 14
Y: 1
Extend the drawer slides out from the cabinet. Align the rst small hole on the drawer slide with the pre-drilled hole
on the front of the drawer sides. From the inside of the drawer, secure the drawer to the slides using one M4x8mm
Bolt (P) on each side, as shown.
NOTE: The drawer sides have a second pre-drilled hole toward the back of the drawer, this hole is from the

Evenly install four Tacks (L), as shown.
IMPORTANT: If walls are not solid like brick, stone or concrete, you will require special ttings (not included). When
in doubt, consult a professional.
Carefully measure the location of pilot hole before drilling and installing the unit.
WARNING: Check for pipes and electrical wiring before drilling.
• Place wall mounting strap against the wall and mark the position for drilling the hole.
• Using a power drill with a 6mm bit, drill a hole to 30mm depth. If the wall is softer, using a 5mm bit is recommended.
• Insert the wall anchor into the hole until the opening is flush with the wall.
• Secure the strap to the wall using the 25mm screw and washer.
• Use a 2mm drill bit to pre-drill a small pilot hole on the back of the furniture top. Secure the other end of the strap to
the furniture using the 14mm screw and washer.
Page 10 / 11