Sunnydaze Decor Anthony RTA-072 User manual

Biffe Ritz
SIDEBOARD STORAGE & BUFFET CABINET
RTA- 072
Carefully review assembly and care instructions before using this product. Save this document for future reference.

Thank you for choosing Sunnydaze Decor. We stand behind our brand and the quality of the items we sell.
Replacement parts or products will be sent at our discretion within the 1-year warranty period. Proof of purchase, with
the date of purchase as well as photos of the merchandise defect, must be provided. Photos are used to determine
the cause of defects and for future quality control. Register your warranty at https://tiny.cc/SunnydazeWarranty
If you have any questions, comments or concerns, feel free to contact us by phone at 833-982-1977, by email:
[e-mail], or via our contact us page at https://tiny.cc/SunnydazeContact
Purchase Date: / / Order/Customer Reference Number:
  
ABottom Panel 1
BLeft Panel 1
CRight Panel 1
DTop Panel 1
EShelf 1
FLeft Middle Panel 1
GRight Middle Panel 1
HEnd Panel 4
IUpper Back Panel 1
JSide Shelf 2
KMiddle Shelf 1
LRight Door 1
MLeft Door 1
NBacking Board 2
OMiddle Panel 1
Inspect packaging to ensure all
parts are accounted for before
disposing of packing materials.
CHOKING HAZARD — This item contains small parts that can be
swallowed. Keep children and pets away during assembly.
WARNING
 (not included)
Phillips Screwdriver Rubber Mallet Hammer Power Drill with
1/8" Bit & 1/4" Bit
  
1Wood Dowel 58
2Spreading Bolt 40
3Cam Lock 40
4Cover Cap 40
5Handle + 3/4" Screws 2
6Door Stop 2
7Hinge + M8 x 1/2" Screws 4
8Nail 24
9Foot 4
10 M6 x 1/2" Flat Screw 16
11 Rear Panel Clamp 4
12 Tipover Restraint Kit 2
Page 1 / 1010/2022

INTRODUCTION
Instrucciones
Instructions


Read the manual carefully to ensure you fully understand
all use, care, assembly, and safety information.
Read this manual carefully and
follow the assembly instructions
in the order listed. Pay close
attention to assembly drawings.
Regularly clean with a clean
    
accumulation.
Do not paint the unit.
Do not use abrasive materials or
cleaners to clean the furniture;
only use a slightly moistened cloth.
Indoor use only.
Do not expose the furniture to
heat or humidity.
When cleaning nearby the
furniture, do not allow contact
with water or cleaners as they
can deteriorate the furniture.
Do not allow metal components
to come in contact with water or
cleaners as it may cause rust and
staining.

dry surface.
Use a soft, protective barrier when
assembling the furniture.
TIP: Use the box carton as a
protective layer to separate and
protect the parts from scratches and
other damage during assembly.
Do not push or drag furniture as
doing so may damage the unit.
Only move furniture when it is empty.
Always ask for help when moving
furniture.
Avoid Accidents - Do not climb, sit
or stand on the furniture.
Do not allow children to play on or
inside the furniture.
Keep sharp objects away as they
may scratch or damage the unit.
Do not use the furniture as a writing
surface without a padded barrier.
Biffe Ritz
Install wood dowels by gently tapping
them into the designated hole using a
rubber mallet.
    
pressing them into the hole or gently
tapping with a rubber mallet until the

Align the cam lock opening (arrow)
with the pre-drilled hole on the side
of the panel. Use a screwdriver to
adjust alignment as needed.
Wood Dowel Spreading Bolt Cam Lock
IMPORTANT INSTALLATION INFORMATION
For the stability of the unit, it is important that furniture connectors are installed correctly.
See drawings and tips below for proper installation.
Page 2 / 1010/2022

Biffe Ritz
ASSEMBLY
STEP 1
B: 1
1: 4
2: 5
3: 2
7: 2
Review all steps carefully and understand assembly before beginning.
STEP 2
C: 1
1: 4
2: 5
3: 2
7: 2
STEP 3
D: 1
2: 5
STEP 5
2: 6
3: 2



Spreading Bolts (2), and two Cam
Locks (3) into Left Panel (B). Then
secure two Hinges (7), as shown.
Do not fully tighten the hinge screws.
Save the remaining screws for Step 33.

Spreading Bolts (2), and two Cam
Locks (3) into Right Panel (C).
Then secure two Hinges (7).
Do not fully tighten the hinge screws.
Save the remaining screws for Step 33.

Top Panel (D).
Install four Wood Dowels (1), and
three Spreading Bolts (2) into
Shelf (E) as shown.
Turn the shelf over.
Install six Spreading Bolts (2) and
two Cam Locks (3) into Shelf (E)
as shown.
Install four Wood Dowels (1), three
Spreading Bolts (2), and two Cam
Locks (3) into Left Middle Panel
(F) as shown.
Turn the panel over.

 
STEP 6
F: 1
1: 4
2: 3
3: 2
STEP 4
E: 1
1: 4
2: 3
Page 3 / 1010/2022

STEP 10
H: 4
1: 16
3: 16
STEP 7
2: 1
STEP 8
G: 1
1: 4
2: 3
3: 2
STEP 9
2: 1
STEP 11
I: 1
1: 6
3: 6

Install one Spreading Bolt (2) into
Left Middle Panel (F) as shown.
Install four Wood Dowels (1), three
Spreading Bolts (2), and two Cam
Locks (3) into Right Middle Panel
(G) as shown.
Turn the panel over.
Install one Spreading Bolt (2) into
Right Middle Panel (G) as shown.
Install four Wood Dowels (1)
and four Cam Locks (3) into End
Panels (H) as shown.
Repeat this step on the remaining
three End Panels (H).
Install six Wood Dowels (1) and
six Cam Locks (3) into Upper Back
Panel (I) as shown.
Install four Wood Dowels (1) and
two Cam Locks (3) into Side Shelf
(J) as shown.
Repeat this step on the remaining
Side Shelf (J).
Biffe Ritz
STEP 12
J: 2
1: 8
3: 4

 
Page 4 / 1010/2022

Biffe Ritz
STEP 14
O: 1
1: 4
3: 2
STEP 17

STEP 16
2: 8
6: 2
STEP 18
Install four Wood Dowels (1) and
two Cam Locks (3) into Middle
Shelf (K) as shown.
Install four Wood Dowels (1) and
two Cam Locks (3) into Middle
Panel (O) as shown.
Secure one Foot (9) to the bottom
of Bottom Panel (A) using four M6
x 1/2" Screws (10).
Repeat this step to secure the
remaining three Feet (9).
Turn the panel over.
Install eight Spreading Bolts
(2), and two Door Stops (6) into
Bottom Panel (A) as shown.
Ensuring the panels are installed
facing the directions shown in the
diagram, place Upper Back Panel
(I) onto Shelf (E).
Use a screwdriver to turn each
cam lock until it locks onto the
head of the spreading bolt.
    
facing the back panel, align Middle
Panel (O) with Shelf (E) as shown.
Use a screwdriver to turn the cam
lock until it locks onto the head of
the spreading bolt.

STEP 13
K: 1
1: 4
3: 2
 STEP 15
A: 1
9: 4
10: 16
 
Page 5 / 1010/2022