Sunnydaze Decor BEARDBOARD DTA-300 User manual

DM-233
BEADBOARD 5-DRAWER DRESSER
DTA-300
Carefully review assembly and care instructions before using this product. Save this document for future reference.

Thank you for choosing Sunnydaze Decor. We stand behind our brand and the quality of the items we sell.
Replacement parts or products will be sent at our discretion within the 1-year warranty period. Proof of purchase, with
the date of purchase as well as photos of the merchandise defect, must be provided. Photos are used to determine
the cause of defects and for future quality control. Register your warranty at https://tiny.cc/SunnydazeWarranty
If you have any questions, comments or concerns, feel free to contact us by phone at 833-982-1977, by email:
[e-mail], or via our contact us page at https://tiny.cc/SunnydazeContact
Purchase Date: / / Order/Customer Reference Number:
08/2022
HELPFUL HINTS
Sunnydaze Decor advises reviewing this manual fully, and assembling the unit soon after purchase.
Check that all parts are accounted for and familiarize yourself with the assembly before beginning.

Page 1 / 11

INTRODUCTION
Instrucciones
Instructions


Read the manual carefully to ensure you fully understand
all use, care, assembly, and safety information.
Read this manual carefully and
follow the assembly instructions
in the order listed. Pay close
attention to assembly drawings.
Regularly clean with a clean
    
accumulation.
Do not paint the unit.
Do not use abrasive materials or
cleaners to clean the furniture;
only use a slightly moistened cloth.
Indoor use only.
Do not expose the furniture to
heat or humidity.
When cleaning nearby the
furniture, do not allow contact
with water or cleaners as it may
deteriorate the furniture.
Do not allow metal components
to come in contact with water or
cleaners as it may cause rust and
staining.

dry surface.
Use a soft, protective barrier when
assembling the furniture.
TIP: Use the box carton as a
protective layer to separate and
protect the parts from scratches and
other damage during assembly.
Do not push or drag furniture as
doing so may damage the unit.
Only move furniture when it is empty.
Always ask for help when moving
furniture.
Avoid Accidents - Do not climb, sit
or stand on the furniture.
Do not allow children to play on or
inside the furniture.
Keep sharp objects away as they
may scratch or damage the unit.
Do not use the furniture as a writing
surface without a padded barrier.
DM-233 08/2022
NOTICE:
Manufacturer and seller expressly disclaim any and all liability from personal injury, property damage
or loss, whether direct or indirect, or incidental, resulting from the incorrect attachment, improper use,

Never open more than one
drawer at a time.
Place heaviest items in the lowest
drawers.
Never put a TV on this product.
Page 2 / 11

  
AWood Dowel 34
BPlastic Foot 4
CM3.5x14mm Flat Screw 48
DM6x8mm Set Screw 20
DE M5x50mm Screw 1
EM4x10mm Screw 8
FCam Screw 38
GCam Lock 38
HM1.5X22mm Nail 38
HE Angle Bracket 1
IKnob 8
JMending Wedge 16
LWall Anchor 1
L1 Left Drawer Slide Track 5
L2 Left Drawer Slide 5
MH-Channel 1
NM3.5x40mm Flat Screw 2
OMending Plate 4
R1 Right Drawer Slide Track 5
R2 Right Drawer Slide 5
COMPONENTS
DM-233 08/2022
Inspect packaging to ensure all
parts are accounted for before
disposing of packing materials.
CHOKING HAZARD — This item contains small
parts that can be swallowed. Keep children and
pets away during assembly.
WARNING
 (not included)
Phillips Screwdriver Rubber Mallet Hammer Power Drill with Bit
  
1Right Side Panel 1
2Left Side Panel 1
3Top Panel 1
4Divider Panel 1
5Crossbeam 4
6Bottom Panel 1
7Large Back Panel 2
8Small Drawer Bottom 2
9Large Drawer Bottom 3
10 Drawer Side Panel (L/R) 10
11 Small Drawer Back 2
12 Small Drawer Front 2
13 Large Drawer Front 3
14 Small Back Panel 1
15 Large Drawer Back 3
Page 3 / 11

Install wood dowels by gently tapping
them into the designated hole using a
rubber mallet.
Use a screwdriver to tighten the cam

the panel. Do not over-tighten or
under-tighten.
Align the cam lock opening (arrow)
with the pre-drilled hole on the side
of the panel. Use a screwdriver to
adjust alignment as needed.
DM-233 08/2022
ASSEMBLY
Wood Dowel Cam Screw Cam Lock
IMPORTANT INSTALLATION INFORMATION
For the stability of the unit, it is important that furniture connectors are installed correctly.
See drawings and tips below for proper installation.
STEP 1
01: 1
02: 1
03: 1
F: 18
STEP 2
04: 1
05: 4
06: 1
A: 14


TIP: Install wood dowels by gently
tapping them into the designated
hole using a rubber mallet.
Page 4 / 11

DM-233 08/2022
STEP 3
B: 4
C: 10
D: 20
H: 4
L1: 5
R1: 5

IMPORTANT:
Install Flat Screw (C)
after
Set Screws (D).
Page 5 / 11
IMPORTANT:
Ensure the slide tracks are installed correctly,
as indicated in the drawings.

DM-233 08/2022
STEP 4
N: 2
STEP 5
G: 6


Page 6 / 11

DM-233 08/2022
STEP 6
G: 6
STEP 7
G: 6


Page 7 / 11

DM-233 08/2022
STEP 8
07: 2
14: 1
H: 34
M: 1
O: 4
STEP 9
10: 10
11: 2
12: 2
13: 3
15: 3
A: 20
F: 20


Page 8 / 11

DM-233 08/2022
STEP 10
08: 2
09: 3
C: 16
G: 20
J: 16
STEP 11
L2: 5
R2: 5
C: 20
E: 8
I: 8


Page 9 / 11
IMPORTANT:
Ensure the slide tracks are
installed in the correct direction,
as indicated in the drawings.

DM-233 08/2022
STEP 12
C: 2
DE: 1
HE: 1
L: 1

IMPORTANT:
Carefully measure the location of pilot hole before drilling and installing the wall anchor.
WARNING:
 
Tipover Restraint Installation
• Ensuring it is at least 20mm from the top of the unit and flush with the back panel, fasten Angle Bracket
(HE) to the divider panel using two M3.5x14mm Flat Screws (C).
• Place the unit against the wall and slowly drill a pilot hole through the hole in the angle bracket and
into the wall. IMPORTANT: Ensure the pilot hole depth does not exceed the length of the wall anchor.
• Move the unit away from the wall. Insert the wall anchor into the pilot hole until the opening of the
anchor is flush with the wall. The wall anchor must be well fitted and tight in the pilot hole.
• With assistance, realign the unit with the wall, ensuring the angle bracket aligns with the wall anchor.
Use M5x50mm Screw (DE) to secure the bracket to the wall anchor.
Assistance required for moving the furniture.
NOTICE:
Manufacturer and seller expressly disclaim any and all liability from personal injury, property damage or loss, whether
direct or indirect, or incidental, resulting from the incorrect attachment, improper use, inadequate maintenance, or neglect

Page 10 / 11