Sunnydaze Decor AGR-362 User manual

CRG922 02/2023
2-DOOR ACCENT CUPBOARD
AGR-362
Carefully review assembly and care instructions before using this product. Save this document for future reference.

Thank you for choosing Sunnydaze Decor. We stand behind our brand and the quality of the items we sell.
Replacement parts or products will be sent at our discretion within the 1-year warranty period. Proof of purchase, with
the date of purchase as well as photos of the merchandise defect, must be provided. Photos are used to determine
the cause of defects and for future quality control. Register your warranty at https://tiny.cc/SunnydazeWarranty
If you have any questions, comments or concerns, feel free to contact us by phone at 833-982-1977, by email:
[e-mail], or via our contact us page at https://tiny.cc/SunnydazeContact
Purchase Date: / / Order/Customer Reference Number:
HELPFUL HINTS
Sunnydaze Decor advises reviewing this manual fully, and assembling the unit soon after purchase.
Check that all parts are accounted for and familiarize yourself with the assembly before beginning.

2-PERSON
ASSEMBLY
RECOMMENDED
Inspect packaging to ensure all
parts are accounted for before
disposing of packing materials.
Save the packing slip.
SCAN THIS CODE
WITH YOUR
SMARTPHONE
TO VIEW OUR
ASSEMBLY VIDEO
Page 1 / 11

CRG922 02/2023
INTRODUCTION
Instrucciones
Instructions


Read the manual carefully to ensure you fully understand
all use, care, assembly, and safety information.
Read this manual carefully and
follow the assembly instructions
in the order listed. Pay close
attention to assembly drawings.
Regularly clean with a clean
microber cloth to prevent dust
accumulation.
Do not paint the unit.
Do not use abrasive materials or
cleaners to clean the furniture.
Indoor use only.
Do not expose the furniture to
heat or humidity.
When cleaning nearby the
furniture, do not allow contact
with water or cleaners as it may
deteriorate the furniture.
Do not allow metal components
to come in contact with water or
cleaners as it may cause rust and
staining.
Assemble on a soft, at, clean, and
dry surface.
Use a soft, protective barrier when
assembling the furniture.
TIP: Use the box carton as a
protective layer to separate and
protect the parts from scratches and
other damage during assembly.
Do not push or drag furniture as
doing so may damage the unit.
Only move furniture when it is empty.
Always ask for help when moving
furniture.
Avoid Accidents - Do not climb, sit
or stand on the furniture.
Do not allow children to play on or
inside the furniture.
Keep sharp objects away as they
may scratch or damage the unit.
Do not use the furniture as a writing
surface without a padded barrier.
NOTICE:
Manufacturer and seller expressly disclaim any and all liability from personal injury, property damage
or loss, whether direct or indirect, or incidental, resulting from the incorrect attachment, improper use,

Page 2 / 11

CRG922 02/2023
COMPONENTS
  
AWood Dowel 22
BM3.5x25mm Pan Screw 4
CM4.5x28mm Pan Screw 23
DConnector 12
ETack 8
FShelf Pin 8
GHandle Set 2
HStrike 2
JCatch 2
KHinge 6
LM3.5x14mm Pan Screw 49
YWall Anchor Kit 1
Z8x8mm Nail 26
  
01 Top 1
02 Left Side Panel 1
03 Right Side Panel 1
04 Shelf 2
05 Bottom Panel 1
06 Bottom Frame 1
07 Top Face Frame 1
08 Side Trim Board (L/R) 2
09 Front Trim Board 1
10 Backing Board 2
11 Divider 1
12 Left Stile 1
13 Right Stile 1
14 Vertical Face Frame 1
15 Left Door 1
16 Right Door 1
(not included)
Phillips
Screwdriver
Regular
Screwdriver
Rubber Mallet
Hammer
Power Drill,
6mm Drill Bit,
2mm Drill Bit
CHOKING HAZARD —
This item contains small parts that can be swallowed.
Keep children and pets away during assembly.
WARNING
(only use for wall anchor kit install)
Inspect packaging to ensure all
parts are accounted for before
disposing of packing materials.
Save the packing slip.
Page 3 / 11

CRG922 02/2023
IMPORTANT: Take care not to over-tighten screws as doing so may crack the wood or strip the screw hole, causing a weak connection and reduced stability.
ASSEMBLY
Carefully review all steps and fully understand assembly before beginning.
STEP 1
06: 1
07: 1
A: 8
STEP 2
05: 1
A: 4
J: 2
L: 4
STEP 3
02: 1
03: 1
A: 10 Install ve Wood Dowels
(A) into Left Side Panel (02)
and Right Side Panel (03).
Install four Wood Dowels
(A) into Bottom Frame (06)
and Top Face Frame (07).
Install four Wood Dowels
(A) into Bottom Panel (05).
Align two Catches (L) with
the indents on the top,
front side of the bottom
panel. Secure each catch
using two M3.5x14mm Pan
Screws (L).
Page 4 / 11

CRG922 02/2023
STEP 5
12: 1
13: 1
C: 8
STEP 4
D: 12
F: 8
IMPORTANT:
Ensure the stiles are installed in the correct direction,
as indicated in the diagrams.
TIP: Install connectors and shelf pins by
gently tapping them into the designated
holes using a rubber mallet.
With the angled edges facing the inside of the panel, install six Connectors (D) into Left Side Panel (02) and Right
Side Panel (03). Install four Shelf Pins (F) into each side panel as shown in the diagrams.
NOTE: On the narrow side of the stiles, the 'bottom' has a larger gap between the dowel mounting holes and the end.
NOTE: The 'top' of the side panels have two connectors on the short edge.
Align Left Stile (12) with Left Side Panel (02) and secure using four M4.5x28mm Pan Screws (C).
Align Right Stile (13) with Right Side Panel (03) and secure using four M4.5x28mm Pan Screws (C).
Page 5 / 11

CRG922 02/2023
STEP 7
8: 2
C: 4
STEP 6
B: 4
C: 4
IMPORTANT: Ensure Bottom Frame (06) is installed in the correct direction, as indicated by the diagram.
Lay Left Side Panel (02) on a smooth, clean surface. Ensuring the catches face the top of the cabinet, align Bottom
Panel (05) just above the bottom connector of the side panel and secure using two M4.5x28mm Pan Screws (C).
On Bottom Frame (06), identify the gap sizes between the pre-drilled round holes and the edges of the panel. Ensuring
the larger gap is facing the top of the cabinet, align Bottom Frame (06) with the mounting holes on the bottom of the stile.
Then, align Top Face Frame (07) with the top of the stile. Secure each frame using one M3.5x25mm Pan Screw (B).
Align Right Side Panel (03) with the opposite side of the unit. Secure the bottom panel using two M4.5x28mm Pan
Screws (C), and secure each frame using M3.5x25mm Pan Screws (B).
Align two Side Trim Boards (08) with the bottom of the unit, as shown. From the inside of the side panels, secure each
trim board using two M4.5x28mm Pan Screws (C).
NOTE: Have an assistant rmly hold the trim boards in place to ensure they remain ush with the unit while hardware is secured.
Assistance is recommended for this step.
Page 6 / 11

CRG922 02/2023
STEP 8
01: 1
09: 1
C: 7
STEP 9
10: 2
11: 1
Z: 26
Align Front Trim Board (09) with the bottom, front side of the unit. Have an assistant hold the trim board tightly to
ensure it remains ush with the unit while it is secured. From the backside of the bottom frame, secure the trim board
using three M4.5x28mm Pan Screws (C).
Place Top (01) on a soft, clean surface. Align the cabinet with the top and secure using four M4.5x28mm Pan Screws (C).
Assistance is recommended for this step.
Gently lay the unit face-down on a soft, clean surface.
Place two Backing Boards (10) on the back of the unit and slide Divider (11) between them.
Ensure the backing boards are snug within the lips of the top and side panels. Then, secure the backing board using
twenty-six 8x8mm Nails (Z).
Page 7 / 11

CRG922 02/2023
STEP 10
14: 1
15: 1
G: 1
H: 1
K: 3
L: 16
STEP 11
16: 1
G: 1
H: 1
K: 3
L: 11
IMPORTANT:
Note the direction of the hinge mounting holes and install as shown in the diagram.

Lay Right Door (16)
face-down on a soft, clean surface.
Align Strike (H) with the indents on the bottom of the door and secure using two M3.5x14mm Pan Screws (L).
Flip the door over.
Ensuring the handle plate and ring remain straight, rmly secure Handle Set (G), as shown.
Align three Hinges (K) with the indents on the front of the door and mostly fasten using nine M3.5x14mm Pan Screws (L).
Lay Left Door (15)
face-down on a soft,
clean surface.
Align Vertical Face Frame (14)
with the indents and secure using
ve M3.5x14mm Pan Screws (L).
Align Strike (H) with the indents on the bottom of the door and secure using two M3.5x14mm Pan Screws (L).
Flip the door over.
Ensuring the handle plate and ring remain straight, rmly secure Handle Set (G), as shown.
Align three Hinges (K) with the indents on the front of the door and mostly fasten using nine M3.5x14mm Pan Screws (L).
IMPORTANT:
Note the direction of the hinge mounting holes and install as shown in the diagram.

Page 8 / 11

CRG922 02/2023
STEP 12
4: 2
STEP 13
L: 18
Ensuring the nished edge faces the front of the
cabinet, place two Shelves (04) on the shelf pins.
TIP: Hold the shelf at an angle to t it between the stiles.
IMPORTANT: Ensure the doors
are properly aligned before fully
securing any screws.
With assistance to hold the door in place, align the hinges of Left Door (15) with the indents on the left stile. Loosely
secure each hinge using three M3.5x14mm Pan Screws (L).
Repeat this step to attach Right Door (16) to the right stile.
After ensuring the doors are properly aligned, fully tighten all screws.
Assistance is recommended for this step.
Page 9 / 11

CRG922 02/2023
STEP 14
E: 8
For even spacing, carefully measure and install eight Tacks (E) as indicated above.
30 mm
30 mm
30 mm
25 mm
40 mm
45 mm
HELPFUL MEASURING HACK
To help ensure tacks are evenly spaced, we developed a hack to make this step easier.
Grab a blank white piece of paper or tracing paper, a writing utensil, a ruler and scissors.
The blocks below are sized to the dimensions noted in the above diagrams.
Place the blank piece of paper over the blocks below. Use a writing utensil to mark the corner of each block.
Use a ruler to connect the dots of each block. Write the size inside the block and cut them out.
Align the cutout with the designated corner (shown above).
Use the sharp end of one of the tacks to make a small indent at inside corner of cutout.
After tack placement has been marked, install tacks using a rubber mallet.
Page 10 / 11