Sunrise Medical Zippie TS User manual

O w n e r ’ s M a n u a l
Zippie TS®
*with transit option *without transit option
Supplier: This manual must be given to the rider of this wheelchair.
Rider: Before using this wheelchair read this entire manual and save it
for future reference.
M a n u a l d e I n s t r u c c i o n e s
Zippie TS®
Distribuidor: Este manual debe ser entregado al pasajero de esta silla de
ruedas.
Pasajero: Antes de usar esta silla de ruedas, lea este manual en su totali-
dad y guárdelo para futura referencia.
Cada una de las sillas se envía con un manual de instrucciones en inglés. El manual en español
o francés está disponible en formato PDF en nuestra página en Internet: www.SunriseMedical.
com. Ingrese a la página del producto específico para descargar el manual, o comuníquese con el
proveedor autorizado de Sunrise Medical.
M o d e d ’ e m p l o i
Zippie TS®
Fournisseur: Ce manuel doit être remis à l’utilisateur / utilisatrice de ce
fauteuil roulant.
Utilisateur / Utilisatrice: Avant d’utiliser ce fauteuil roulant, lisez
entièrement ce manuel et conservez le
pour le consulter ultérieurement.
Chaque fauteuil est livré avec un manuel d’instructions en anglais. Les versions en espagnol et
en francais sont à ançais est à votre disposition en format PDF sur le site: www.SunriseMedical.
com. Veuillez vous rendre à la page de votre produit pour télécharger le manuel dans la langue
souhaitée, ou contactez un fournisseur agréé Sunrise Medical.
TS

MK-100208 RevB 2
ZIPPIE TS
SUNRISE MEDICAL LISTENS
Thank you for choosing a Zippie wheelchair. We want to hear your
questions or comments about this manual, the safety and reliability of
your chair, and the service you receive from your Sunrise Medical autho-
rized dealer. Please feel free to write or call us at the address and tele-
phone number below:
Be sure to register your wheelchair, and let us know if you change your
address. This will allow us to keep you up to date with information
about safety, new products, and options to increase your use and enjoy-
ment of this wheelchair.
You can also register your wheelchair at: www.SunriseMedical.com/reg-
ister
FOR ANSWERS TO YOUR QUESTIONS
Your Sunrise Medical authorized dealer knows your wheelchair best, and
can answer most of your questions about chair safety, use and mainte-
nance. For future reference, fill in the following:
Dealer: ___________________________________________
Address: __________________________________________
_________________________________________________
Telephone: ________________________________________
Serial #:_________________ Date/Purchased: _____________
ADDITIONAL INFORMATION YOU SHOULD KNOW
No component of this chair was made with natural latex rubber.
DISPOSAL AND RECYCLING INFORMATION
When this product reaches the end of its life, please take it to an
approved collection or recycling point designated by your local or state
government. This wheelchair is manufactured using a variety of materials.
Your product should not be disposed of as ordinary household waste.
You should dispose of your wheelchair properly, according to local laws
and regulations. Most materials that are used in the construction of this
product are fully recyclable. The separate collection and recycling of
your product at the time of disposal will help conserve natural resources
and ensure that it is disposed in a manner that protects the environ-
ment.
Ensure you are the legal owner of the product prior to arranging for the
product disposal in accordance with the above recommendations.
I. I NT RO DUCTION
www.SunriseMedical.com/register
If you are visually impaired,
this document can be
viewed in PDF format at
www.SunriseMedical.com
Dealer signature and stamp
in United Kingdom:
SUNRISE MEDICAL LTD.
Sunrise Medical Ltd.
Thorns Road
Brierley Hill
West Midlands
DY5 2LD
England
Phone: [phone]
Fax: [phone]
www.SunriseMedical.co.uk
in North America:
SUNRISE MEDICAL (US) LLC
Customer Service Department
2842 N. Business Park Avenue
Fresno, CA 93727 USA
[phone]
[phone]
www.SunriseMedical.com

MK-100208 RevB
3
ZIPPIE TS
I. INTRODUCTION ................................................ 2
II. TABLE OF CONTENTS...................................... 3
III. YOUR CHAIR AND ITS PARTS ........................ 4
IV. NOTICE - READ BEFORE USE.......................... 4
A. Choose the Right Chair and Safety Options ......... 4
B. Review This Manual Often ......................................... 4
C. Warnings.......................................................................... 4
V. GENERAL WARNINGS....................................... 5
A. Weight Limit .................................................................. 5
B. Intended Use................................................................... 5
C. Area of Application ....................................................... 5
D. Attendants and Caregivers .......................................... 5
E. Accessories...................................................................... 5
F. Know Your Chair ......................................................... 5
G. Reduce The Risk of an Accident ............................... 5
H. Safety Checklist ............................................................. 6
I. Changes and Adjustments .......................................... 6
J. Environmental Conditions .......................................... 6
K. Terrain ............................................................................. 6
L. Street Use ...................................................................... 6
M. Motor Vehicle Safety ................................................... 7
N. When You Need Help ................................................ 7
VI. SAFETY WARNINGS: FALLS AND TIP-OVERS . 8
A. Center of Balance ......................................................... 8
B. Dressing or Changing Clothes .................................. 8
C. Obstacles ........................................................................ 8
D. Front Caster Lift ............................................................ 8
E. Reaching or Leaning ...................................................... 8
F. Moving Backward........................................................... 8
G. Escalators ......................................................................... 9
H. Ramps, Slopes and Sidehills ........................................ 9
I. Transfers .......................................................................... 10
J. Curbs and Single Steps ................................................. 10
K. Climbing a Curb or Single Step .................................. 11
L. Descending a Curb or Single Step............................. 11
M. Stairs.................................................................................. 11
N. Climbing Stairs ............................................................... 11
O. Descending Stairs ......................................................... 11
VII. WARNINGS: COMPONENTS AND OPTIONS. 12
A. Anti-Tip Tubes .............................................................. 12
B. Armrests ......................................................................... 12
C. Cushion and Sling Seats .............................................. 12
D. Fasteners ......................................................................... 12
E. Footrests.......................................................................... 12
F. Pneumatic Tires ............................................................ 12
G. Positioning Belts Option .............................................. 13
H. Push Handles Option .................................................... 13
I. Quick-Release Axles .................................................... 13
J. Rear Wheels .................................................................. 13
K. Rear Wheel Locks ........................................................ 13
L. Modified Seat Systems ................................................. 14
M. Seat and Back Upholstery ........................................... 14
N. Power Drive.................................................................... 14
O. Dynamic Backrest .......................................................... 14
P. Anti-tip Receivers .......................................................... 14
VIII. USE AND MAINTENANCE .............................. 15
A. Introduction..................................................................... 15
B. Critical Maintenance Tips ............................................ 15
C. Cleaning Tips................................................................... 15
D. Safety Checklist .............................................................. 15
E. Troubleshooting Chart................................................. 15
F. To Mount and Remove Rear Wheels....................... 16
G. Wheel Locks ................................................................... 16
H. Hub Locks........................................................................ 16
I. Anti-tips............................................................................ 17
J. Single-Post Height Adjustable Armrest .................... 17
K. Z-Finity™ Footrest system (Option)........................ 18
L. Swing In/Out Hangers and Footrests........................ 18
M. Heavy-duty Lift-off Footrests (Option) .................... 18
N. Articulating/Elevating Legrest (Option) .................... 18
O. Folding and Unfolding ................................................... 19
P. Integrated Stroller Handles ......................................... 19
Q. Backrest............................................................................ 19
R. Storage Tips..................................................................... 20
S. Hygiene Measures When Being Re-used ................. 20
T. Check-Out....................................................................... 20
IX. DEALER SERVICE AND ADJUSTMENT .......... 21
A. Dealer Service Introduction........................................ 21
B. Critical Maintenance Tips ............................................ 21
C. Cleaning............................................................................ 21
D. Rear Wheel Adjustment .............................................. 21
E. Rear Wheel Axle Nut Adjustment............................ 22
F. Wheel Locks ................................................................... 22
G. Hub Locks........................................................................ 22
H. Anti-tip Receivers .......................................................... 22
I. Armrest Receiver Attachment .................................. 23
J. Flip-up Armrests............................................................. 23
K. Adjustable Locking Flip-up Armrest.......................... 23
L. T-post Armrest ............................................................. 23
M. Z-Finity™ Footrest System......................................... 24
N. Articulating Legrest ...................................................... 24
O. Elevating Legrest............................................................. 24
P. Kids and Adult Angle Adjustable Footplates........... 25
Q. Aluminum Footplate...................................................... 25
R. 90° Footboard ............................................................... 25
S. Caster Forks.................................................................... 25
T. Caster Plates ................................................................... 26
U. Seat Depth....................................................................... 26
V. Solid Back and Seat Insert............................................ 27
W. Tilt-in-Space..................................................................... 27
X. Cable Adjustment .......................................................... 28
Y. Cross-Brace..................................................................... 28
Z. Strut Tube Assembly..................................................... 28
AA.Growing Seat Pan .......................................................... 29
BB Check out ........................................................................ 29
XI. NAMEPLATE ....................................................... 30
X. SUNRISE LIMITED WARRANTY ..................... 31
II. TABLE OF CONTENTS

IV. NOTICE- READ BEFORE USE
MK-100208 RevB 4
ZIPPIE TS
III. YOUR CHAIR AND ITS PARTS
A. CHOOSE THE RIGHT CHAIR AND SAFETY
OPTIONS
Sunrise provides a choice of many wheelchair styles to meet your needs.
This product is intended for single person use only. Final selection of the
type of wheelchair, options and adjustments rests solely with you and your
health care provider. Choosing the best chair for your unique mobility needs
will depend on such things as:
1. Your disability, strength, balance and coordination.
2. The types of hazards you must overcome in daily use (where you
live and work, and other places you are likely to use your chair).
3. The need for options that will improve your positioning, safety and
comfort (such as anti-tip tubes, positioning belts, or special seating
systems).
B. REVIEW THIS MANUAL OFTEN
Before using this chair you, and each person who may assist you, should
read this entire manual and ensure you follow all instructions. Review the
warnings often, until they are second nature to you.
IMPORTANT:
DO NOT USE YOUR WHEELCHAIR UNTIL THIS
MANUAL HAS BEEN READ AND UNDERSTOOD.
C. WARNINGS
The word “WARNING” refers to a hazard or unsafe practice that may cause
severe injury or death to you or to other persons. The “Warnings” are in
three main sections, as follows:
1. V — GENERAL WARNINGS
Here you will find a safety checklist and a summary of risks you
need to be aware of before you ride this chair.
2. VI– SAFETY WARNINGS: FALLS AND TIP-OVERS
Here you will learn about practices for the safe use of your chair,
and how to avoid a fall or tip-over while you perform daily activities
in your chair.
3. VII — WARNINGS — COMPONENTS AND
OPTIONS
Here you will learn about the components of your chair and options
you can select for safety. Consult your Sunrise Medical authorized
dealer and your health care provider to help you choose the best
set-up and options for safe use.
NOTE– Where they apply, you will also find “Warnings” in other sec-
tions of this manual. Heed all warnings in these sections. If you
fail to do so a fall, tip-over or loss of control may occur and
cause severe injury to the rider or others.
1. Push Handle
2. Single Post Height Adjustable
Armrest
3. Anti-tip Tube
4. Rear Tire 12-in
5. Quick-Release Axle
6. Foot Lock (Option)
7. Caster Barrel
8. Caster Fork
9. Caster Wheel
10. Adjustable Footplates (Option)
11. Strut Tube (Tilt)
12. Swing in / out Hangers
13. Seat Pan
14. Cushion
15. Lateral (Option)
16. Solid Back
17. Headrest (Option)
ZIPPIE TS®
5
3
2
1
16
9
7
8
4
11
12
14
13
Note: All features may not be available
with some chair setups or in conjunc-
tion with another chair feature. Please
consult your Sunrise Medical authorized
dealer for more information.
6
15
10
17

A. WEIGHT LIMIT
WARNING
NEVER exceed the weight limit specified by Sunrise Medical. The weight
capacity provided by your manufacturer is for the combined weight of
a rider and items carried using on-board storage. If you do exceed the
weight limit, damage to your chair, a fall, tip-over or loss of control may
occur and cause severe injury to the rider or others.
Weight Capacity
Zippie TS®- 165 lbs (75kg)
B. INTENDED USE
The Zippie TS®wheelchair’s intended use is to provide mobility to chil-
dren limited to a sitting position.
The intended lifetime of the wheelchair is 5 years.
WARNING
DO NOT use this device for purposes other than what is intended by the
manufacturer
1. The wheelchair is not designed for weight training and is unsafe for
use as a seat while weight training. Weight training from the wheel-
chair substantially changes the stability of the chair and may cause
tipping.
2. DO NOT stand on the frame of the wheelchair.
3. NEVER allow someone to stand on your chair or use it as a step
ladder.
4. This chair is designed for a single rider only.
5. Unauthorized modifications and use of parts or accessories not
supplied or approved by Sunrise Medical may change the chair
structure. This will void the warranty and may cause a safety hazard.
If the warning is ignored, damage to your chair, and the potential
severe injury of the person using the chair for unintended purposes
can occur.
C. AREA OF APPLICATION
The varieties of fitting variants, as well as the modular design, mean that it
can be used by those who cannot walk or have limited mobility because of:
- Paralysis
- Loss of extremity (leg amputation)
- Extremity defect deformity
- Joint contractures / joint injuries
- Illnesses such as heart and circulation deficiencies, disturbance of equi-
librium or cachexia, Neurological disease patterns, Muscle dystrophy,
Hemiplegia as well as for elderly people who still have strength in the
upper body.
The wheelchair shall not be used without attendant in case of:
- Perception disorder
- Imbalance
- Loss of both arms, if not supported by a caregiver
- Joint contracture or joint damage on both arms
- Seating disability
When considering provision, please also note the body size, weight, phys-
ical and psychological constitution, the age of the person, living conditions
and environment.
NOTE:
Please note that driving a wheelchair requires sufficient cognitive, physical
and visual skills. The user must be able to assess the effects of actions
during the operation of the wheelchair and, if necessary, to correct them.
These capabilities and the safe use of the additionally attached components
cannot be assessed by Sunrise Medical as a manufacturer. We cannot
accept any liability for any damage resulting from this.
Please refer to the operating instructions of the wheelchair and the addi-
tionally mounted components. Instruct the user in the safe use of the
wheelchair and the additionally mounted components. Inform users of spe-
cific warnings that need to be read, understood, and respected.
D. ATTENDANTS AND CAREGIVERS
WARNING
Before you assist a rider, ensure you read all warnings contained in this
manual, and follow all instructions that apply. Be aware that after consult-
ing a healthcare provider, you will need to learn safe and proven body
mechanics to use and create assistive methods best suited to your abilities.
E. ACCESSORIES
WARNING
Unauthorized modifications or use of parts, or accessories not supplied or
approved by Sunrise Medical may change the chair structure. This will void
the warranty and may cause a safety hazard.
Some problems that may occur, but are not limited to:
1. Incorrect wheels and/or tires that put the rider at risk of a fall or
tip-over.
2. Adding a component to the frame, changing the structural integrity
of the chair.
3. Any modification or disassembly can potentially create an unsafe
situation where rider and/or attendant are put at risk.
F. KNOW YOUR CHAIR
WARNING
Every wheelchair is different. Take the time to learn the feel of this chair
before you begin riding. Start slowly, with easy, smooth strokes. If you are
use to a different chair, you may use too much force and tip over. If you
use too much force, damage to your chair, a fall, tip-over or loss of control
may occur and cause severe injury to the rider or others.
G. REDUCE THE RISK OF AN ACCIDENT
WARNING
1. BEFORE you begin riding, you should be trained in the safe use of
this chair by your health care provider.
2. Practice bending, reaching and transfers until you know the limit of
your ability. Have someone help you until you know what can cause
a fall or tip-over and how to avoid doing so.
3. Be aware that you must develop your own methods for safe use
best suited to your level of function and ability.
4. NEVER try a new maneuver on your own. Ask the advice of your
health care provider to lower the risk of a fall or tip over.
5. Get to know the areas where you plan to use your chair. Look for
hazards and learn how to avoid them.
MK-100208 RevB
5
ZIPPIE TS
V. GENERAL WARNINGS

MK-100208 RevB 6
ZIPPIE TS V. GENERAL WARNINGS
K. TERRAIN
WARNING
1. Based on ANSI/RESNA testing, Sunrise Medical recommends the
use of a caster wheel with a minimum diameter of 5-in, if the wheel-
chair will be overcoming obstacles up to 1/2-in on a regular basis.
2. Your chair is designed for use on firm, even surfaces such as con-
crete, asphalt, indoor flooring, and carpets.
3. Do not operate your chair in sand, loose soil, or over rocky terrain.
4. If you use your chair on terrain that is rougher than described
above there is a danger that screws and bolts will loosen prema-
turely, and that damage to wheels or axles could put the rider at
risk of a fall, tip-over, or loss of control.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
L. STREET USE
WARNING
1. This product is not intended for street use.
2. Avoid streets whenever possible.
3. Obey and follow all legal pedestrian pathways, and laws that apply to
pedestrians.
4. Be alert to the danger of motor vehicles in parking lots, or if you
must cross a road.
If you fail to heed this warning, damage to your chair, and a possible colli-
sion may occur and cause severe injury to the rider or others.
H. SAFETY CHECKLIST
WARNING
Before Each Use Of Your Chair:
1. Ensure the chair rolls easily and that all parts work smoothly. Check
for noise, vibration, or a change in ease of use. (This may indicate
low tire pressure, loose fasteners, or damage to your chair).
2. Inspect any problem. Your Sunrise Medical authorized dealer can
help you find and correct the problem.
3. Check to see that both quick-release rear axles are locked. When
locked, the axle button will “pop out” fully. If not locked, the wheel
may come off and cause you to fall.
4. If your chair has anti-tip tubes, lock them in place.
I. CHANGES AND ADJUSTMENTS
WARNING
1. See your health care provider and have them adjust seating compo-
nents any time a change or adjustment needs to be made.
2. Unauthorized modifications or use of parts not supplied or
approved by Sunrise may change the chair structure. This will void
the warranty and may cause a safety hazard.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
J. ENVIRONMENTAL CONDITIONS
WARNING
1. Use extra care if you must ride your chair on a wet
or slick surface. If you are in doubt, ask for help.
2. Contact with water or excess moisture may cause
your chair to rust or corrode. Avoid all extreme weather situations
if possible.
a. Do not use your chair in a shower, pool or other body of
water. The chair tubing and parts are not water-tight and may
rust or corrode from the inside.
b. Avoid excess moisture (for example, do not leave your chair in
a damp bathroom while taking a shower).
c. Dry your chair as soon as you can if it gets wet, or if you use
water to clean it.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.

MK-100208 RevB
7
ZIPPIE TS V. GENERAL WARNINGS
M. MOTOR VEHICLE SAFETY 12
If possible and feasible, the rider should transfer to the Original Equipment
Manufacturer vehicle seat and use the OEM vehicle restraint.
Sunrise Medical does provide a WC-19 Wheelchair Tie-Down and
Occupant Restraint System, otherwise called a Transit Option. To identify
whether your wheelchair has been manufactured with the Transit Option
installed, look for four points of securement. Two front points (A), and
two rear points (B). These points are recognized by the securement point
decal which can be found on or near the securement points.
If your wheelchair is equipped with the Transit Option, please
review the Transit Securement supplement that was provided
with the wheelchair for additional information and instructions.
You can request a copy from your Sunrise Medical authorized
dealer, or call Sunrise Medical at 1-800-333-4000 if you don’t have
it.
WARNING
If your chair is NOT equipped with the Transit Option:
1. NEVER let anyone sit in this chair while in a moving vehicle.
a. ALWAYS move the rider to an approved vehicle seat.
b. ALWAYS secure the rider with proper motor vehicle restraints.
2. In an accident or sudden stop the rider may be thrown from the
chair. Wheelchair seat belts will not prevent this, and further injury
may result from the belts or straps.
3. NEVER transport this chair in the front seat of a vehicle. It may shift
and interfere with the driver.
4. ALWAYS secure this chair so that it cannot roll or shift.
5. Do not use any chair that has been involved in a motor vehicle acci-
dent. The frame and/or components may have been changed due to
the accident. Such items could be, but are not limited to: bent, loos-
ened, and/or broken components that were subjected to an impact.
Failure to heed these warnings puts you and others that may assist you at a
high risk of injury.
N. WHEN YOU NEED HELP
WARNING
For The Rider: Ensure that each person who helps you reads and fol-
lows all warnings and instructions that apply.
For Attendants:
1. Work with the rider’s doctor, nurse or therapist to learn safe
methods best suited to your abilities and those of the rider.
2. Tell the rider what you plan to do, and explain what you expect the
rider to do. This will put the rider at ease and reduce the risk of an
accident.
3. Ensure the chair has push handles. They provide secure points for
you to hold the rear of the chair to prevent a fall or tip-over. Check
to ensure push handle grips will not rotate or slip off.
4. To prevent injury to your back, use good posture and proper body mechan-
ics. When you lift or support the rider or tilt the chair, bend your knees
slightly and keep your back as upright and straight as you can.
5. Remind the rider to lean back when you tilt the chair backward.
6. When you descend a curb or single step, slowly lower the chair in
one easy movement. Do not let the chair drop the last few inches
to the ground. This may damage the chair or injure the rider.
7. To avoid tripping, unlock and rotate anti-tip tubes up, out of the way.
8. Whenever you aren’t attending the wheelchair, ALWAYS use the wheel-
lock to secure the rear wheels, and lock the anti-tip tubes in place.
If you fail to ask for help when in doubt, you run a high risk of a fall, tip-over or
loss of control that may occur and cause severe injury to the rider or others.
Look for this symbol on your wheelchair. It indicates wheel-
chair securement points which conform to ANSI/RESNA
(1998) V.1 - Section 19 and/or ANSI/RESNA (2012) V.4
WC-19. For more transit related information, see the “Transit
Securement Supplement” included with your chair.
1 2
A
B
Front Transit hook
Rear Transit hook

MK-100208 RevB 8
ZIPPIE TS
A. CENTER OF BALANCE
WARNING
The point where this chair will tip forward, back or to the side depends on its
center of balance and stability. How your chair is set up, the options you select
and the changes you make may affect the risk of a fall or tip-over.
1. The Most Important Adjustment Is:
The position of the rear wheels. The more you move the rear wheels
forward, the more likely your chair will tip over backward.
2. The Center Of Balance Is Also Affected By:
a. A change in the set-up of your chair, including:
• The distance between the rear wheels.
• The amount of rear wheel camber.
• The seat height and seat angle.
• Backrest angle.
b. A change in your body position, posture or weight distribution.
c. Riding your chair on a ramp or slope.
d. A backpack or other options and the amount of added weight.
3. To Reduce The Risk Of An Accident:
a. Consult your doctor, nurse or therapist to find out what axle and
caster position is best for you.
b. Consult your Sunrise Medical authorized dealer BEFORE you mod-
ify or adjust this chair. Be aware that you may need to make other
changes to correct the center of balance.
c. Have someone help you until you know the balance points of your
chair and how to avoid a tip-over.
d. Use anti-tip tubes.
If you fail to heed these warnings, you are at a high risk of a fall, tip-over or loss
of control that could cause severe injury to the rider or others.
B. DRESSING OR CHANGING CLOTHES
WARNING
Your weight may shift if you dress or change clothes while seated in this chair.
To reduce the risk of a fall or tip-over:
1. Rotate the front casters until they are as far forward as possible.
This makes the chair more stable.
2. Lock anti-tip tubes in place. (If your chair does not have anti-tip tubes,
back it up against a wall and lock both rear wheels).
If you fail to heed this warning, damage to your chair, a fall, tip-over or loss of
control may occur and cause severe injury to the rider or others.
C. OBSTACLES
WARNING
Riding over curbs or obstacles can cause tipping and serious bodily harm. If you
have any doubt that you can safely cross any curb or obstacle, ALWAYS ASK
FOR HELP. Be aware of your riding skills and personal limitations. Develop
new skills only with the help of a companion.
To avoid the risk of traversing obstacles:
1. Keep a lookout for danger – scan the area well ahead of your chair as
you ride.
2. Make sure the floor areas where you live and work are level and free of
obstructions.
3. Remove or cover threshold strips between rooms.
4. Install a ramp at entry or exit doors. Ensure there is not a drop off at the
bottom of the ramp.
5. To Help Correct Your Center Of Balance:
a. Lean your upper body FORWARD slightly as you go UP over an
obstacle.
b. Press your upper body BACKWARD as you go DOWN from a high-
er to a lower level.
6. If your chair has anti-tip tubes, do not go over an obstacle without help.
7. Keep both of your hands on the handrims as you go over an obstacle.
8. Never push or pull on an object (such as furniture or a doorjamb) to
propel your chair.
If you fail to heed these warnings damage to your chair, a fall, tip-over or loss of
control may occur and cause severe injury to the rider or others.
.D. FRONT CASTER LIFT
WARNING
Front caster lift can occur when the front wheels, ordinarily in contact with the
ground, are either intentionally, or unintentionally caused to lift from the ground
while the rear wheels remain in contact. Pitch control (partial or full) should
NEVER be attempted without consulting your health care provider and ensuring
that anti-tips are installed.
If you fail to heed this warning, you are at a high risk of damage to your chair,
a fall, tip-over or loss of control that may occur and cause severe injury to the
rider or others.
E. REACHING OR LEANING
WARNING
If you reach or lean it will affect the center of balance of your chair. This may
cause you to fall or tip over. When in doubt, ask for help or use a device to
extend your reach.
1. NEVER reach or lean if you must shift your weight sideways or rise up off
the seat.
2. NEVER reach or lean if you must move forward in your seat to do so.
Always keep your buttocks in contact with the backrest.
3. NEVER reach with both hands (you may not be able to catch yourself to
prevent a fall if the chair tips).
4. NEVER reach or lean to the rear unless your chair has anti-tip tubes
locked in place.
5. DO NOT reach or lean over the top of the seat back. This may damage
one or both backrest tubes and cause you to fall.
6. If You Must Reach Or Lean:
a. Do not lock the rear wheels. This creates a tip point and makes a fall
or tip-over more likely.
b. Do not put pressure on the footrests.
c.
Move your chair as close as you can to the object you wish to reach.
d. Do not try to pick up an object from the floor by reaching down
between your knees. You are less likely to tip if you reach to the side
of your chair.
e. Rotate the front casters until they are as far forward as possible. This
makes the chair more stable.
f. Firmly grasp a rear wheel or an armrest with one hand. This will help
to prevent a fall if the chair tips.
If you fail to heed these warnings damage to your chair, a fall, tip-over or loss of
control may occur and cause severe injury to the rider or others.
F. MOVING BACKWARD
WARNING
Use extra care when you move your chair backward. Your chair is most stable
when you propel yourself forward. You may lose control or tip over if one of
the rear wheels hits an object and stops rolling.
1. Propel your chair slowly and smoothly.
2. If your chair has anti-tip tubes, ensure you lock them in place.
3. Stop often and check to ensure your path is clear.
If you fail to heed this warning, you are at a high risk of damage to your chair,
a fall, tip-over or loss of control that may occur and cause severe injury to the
rider or others.
VI. SAFETY WARNINGS: FALLS AND TIP-OVERS

MK-100208 RevB 9
ZIPPIE TS VI. SAFETY WARNINGS: FALLS AND TIP-OVERS
3
4
5
6
IF you need to go up a hill:
a. The Upslope should be less than 6°.
b. ALWAYS Go Straight up.
c. DON’T STOP.
d. NEVER turn on a hill.
e. ALWAYS lean forward.
IF you need to traverse a Sidehill:
a. The sidehill must be Less than 6° or you
are at risk of a tip over.
b. DON’T STOP.
c. NEVER turn on a hill.
If you need to traverse a Ramp:
a. Go Slowly.
b. Watch out for Drop-offs.
c. ALWAYS go straight up or straight down.
d. Stay centered on the Ramp.
IF you need to go down a hill:
a. The Downslope should be less than 6°.
b. GO SLOW Control your speed.
c. ALWAYS Go Straight down.
d. Never turn on a hill.
e. ALWAYS lean backward.
G. ESCALATORS
WARNING
NEVER use this chair on an escalator, even with an attendant. If you do, a fall or tip-over is likely.
If you fail to heed this warning you and others that may be assisting you, are at a high risk of severe
injury.
H. RAMPS, SLOPES AND SIDEHILLS 3456
WARNING
Whenever possible, avoid riding on a slope, which includes a ramp or sidehill. This will change the
center of balance of your chair. Your chair is less stable and more difficult to maneuver when it is at
an angle. When moving up a hill, anti-tip tubes may not prevent a fall or tip-over.
1. DO NOT use your chair on a slope steeper than 10%. (A 10% slope means: one foot in ele-
vation for every ten feet of slope length.)
2. ALWAYS go as straight up and as straight down as you can. (Do not “cut the corner” on a
slope or ramp.)
3. DO NOT turn or change direction on a slope.
4. When you have to use a ramp, always stay in the CENTER of the ramp. Ensure ramp is wide
enough that you have no risk of going off the edge.
5. DO NOT stop on a steep slope. If you stop, you may lose control of your chair.
6. NEVER use rear wheel locks to try to slow or stop your chair. This is likely to cause your
chair to veer out of control.
7. ALWAYS be aware of:
a. Wet or slippery surfaces.
b. A change in grade on a slope (or a lip, bump or depression). These may cause a fall or tip-
over.
c. A drop-off at the bottom of a slope or ramp. A drop-off as small as 3/4 inch can stop a
front caster and cause the chair to tip forward.
8. To Reduce The Risk Of A Fall Or Tip-Over:
a. Lean or press your body UPHILL. This will help adjust for the change in the center of bal-
ance caused by the slope or sidehill.
b. Keep pressure on the handrims to control your speed on a down slope. If you go too fast
you may lose control.
c. ASK FOR HELP any time you are in doubt.
9. Ramps At Home and Work– For your safety, ramps at home and work must meet all legal
requirements for your area:
a. AVOID A DROP-OFF
Ensure there is a section at the top or bottom to smooth out the transition.
b. ALWAYS stay in the center of the ramp and control your speed.
If you fail to heed these warnings damage to your chair, a fall, tip-over or loss of control may occur
and can possibly cause severe injury to the rider or others.

MK-100208 RevB
10
ZIPPIE TS
7
Optimum Transfer position
GET READY TRANSFER ADJUST
8
1. 2. 3.
Before transferring:
1. Remove the armrests.
2. Remove or move the footrests.
3. Make sure the wheel lock is set.
VI. SAFETY WARNINGS: FALLS AND TIP-OVERS
I. TRANSFERS 78
WARNING
It is dangerous to transfer on your own. It requires good balance and agility. Be aware that there is a point
during every transfer when the wheelchair seat is not below you. To avoid a fall:
1. Work with your health care provider to learn safe methods for transfers.
a. Learn how to position your body and how to support yourself during a transfer.
b. Have someone help you until you learn safe transfer methods.
2. Lock the rear wheels before you transfer.
3. Be aware that the chair can still slide and/or tip. The wheel lock keeps the rear wheels from rolling
while you are performing the transfer.
4. Ensure that the pneumatic tires are properly inflated. Low tire pressure may allow the rear wheel
locks to slip. (see table in Section 7:F “Pneumatic Tires”).
5. Move your chair as close as you can to the seat you are transferring to. If possible, use a transfer
board.
6. Rotate the front casters until they are as far forward as possible.
7. If you can, remove the footrests, or swing them out of the way.
a. Ensure your feet do not catch in the space between the footrests.
b. Avoid putting weight on the footrests as this may cause the chair to tip.
8. Ensure armrests are removed, or out of the way and do not interfere with the transfer.
9. Transfer as far back onto the seat surface as you can. This will reduce the risk that the chair will tip or
move away from you.
J. CURBS AND SINGLE STEPS 9
WARNING
Before riding over curbs, and negotiating even a single step, ALWAYS ask for assistance first. Curbs and steps
can cause tipping and serious bodily harm. When in doubt as to your ability to avoid, or traverse any obsta-
cle, always ask for help. Be aware of your riding skills and personal limitations. Develop new skills only with
the help of a companion.
For Attendant: Each person who assists the rider with curbs and steps should read and follow all
instructions and warnings pertaining to attendants, and caregivers.
1. Do not try to climb a high curb or step (more than 4 inches high) UNLESS you have help. Doing so may
cause your chair to exceed its balance point and tip over.
2. Go straight up and straight down a curb or step. If you climb or descend at an angle, a fall or tip-over
is likely.
3. Be aware that the impact of dropping down from a curb or step can damage your chair or loosen fas-
teners.
If you fail to heed these warnings damage to your chair, a fall, tip-over or loss of control may occur and can
possibly cause severe injury to the rider or others.

MK-100208 RevB 11
ZIPPIE TS
10
9
VI. SAFETY WARNINGS: FALLS AND TIP-OVERS
K. CLIMBING A CURB OR SINGLE STEP 9
WARNING
For Attendant: follow these steps to help the rider climb a curb or single step going BACKWARD:
1. Stay behind the chair.
2. Continue backward until the rear wheels contact the face of the curb or step. Lift and roll the rear
wheels to the top of the curb.
3. Pull the chair backwards until the caster wheels have cleared the edge of the curb and return the chair
to its rolling position.
If you fail to heed these warnings damage to your chair, a fall, tip-over or loss of control may occur and
cause severe injury to the rider or others.
L. DESCENDING A CURB OR SINGLE STEP 9
WARNING
For Attendant: Follow these steps to help a rider descend a curb or single step going FORWARD:
1. Stay at the rear of the chair.
2. Several feet before you reach the edge of the curb or step, tip the chair slightly and pull it backward.
3. When the chair is at its balance point, carefully step forwards until the rear wheels reach the edge of
the curb or step. Then allow the rear wheels to slowly roll down onto the lower level.
4. Push the chair forward until you are standing on the lower level.
5. When the rear wheels are safely on the lower level, tilt the chair back to its balance point.
If you fail to heed these warnings damage to your chair, a fall, tip-over or loss of control may occur and
cause severe injury to the rider or others.
M. STAIRS 10
WARNING
1. NEVER use this chair on stairs UNLESS you have someone to help you. Doing so is likely to cause a
fall or tip-over.
2. Negotiating stairs with a wheelchair always requires at least two attendants for safety.
If you fail to heed these warnings damage to your chair, a fall, tip-over or loss of control may occur and
cause severe injury to the rider or others.
N. CLIMBING STAIRS 10
WARNING
1. Use at least two attendants to move a chair and rider up stairs.
2. Move the chair and rider BACKWARD up the stairs.
3. The person at the rear is in control. They tilt the chair back to its balance point.
4. A second attendant at the front firmly grasps a non-detachable part of the front frame and lifts the
chair up and over one stair at a time.
5. The attendants move to the next stair up. Repeat for each stair, until you reach the landing.
If you fail to heed these warnings damage to your chair, a fall, tip-over or loss of control may occur and
cause severe injury to the rider or others.
O. DESCENDING STAIRS 10
WARNING
1. Use at least two attendants to move a chair and rider down stairs.
2. Move the chair and rider FORWARD down the stairs.
3. The person at the rear is in control. They tilt the chair to the balance point of the rear wheels and
rolls it to the edge of the top step.
4. A second attendant stands on the third step from the top and grasps the chair frame. They lower the
chair one step at a time by letting the rear wheels roll over the stair edge.
5. The attendants move to the next stair down. Repeat for each stair, until you reach the landing.
If you fail to heed these warnings damage to your chair, a fall, tip-over or loss of control may occur and
cause severe injury to the rider or others.

MK-100208 RevB
12
ZIPPIE TS
VII. WARNINGS: COMPONENTS AND OPTIONS
A. ANTI-TIP TUBES
WARNING
Anti-tip tubes can help keep your chair from tipping over backward in
normal conditions.
1. Sunrise recommends the use of anti-tip tubes:
2. When locked in place (in the “down” position) anti-tip tubes should
be BETWEEN 1 1/2 to 2 inches off the ground.
a. If set higher than 2 inches, they may not prevent a tip-over.
b. If set lower than 2 inches, they may “hang up” on obstacles and
cause a fall or tip over.
3. If you have to climb or descend a curb, or overcome an obstacle it
may be necessary to have an attendant ensure the anti-tip tubes are
rotated up, and out of the way, so that the chair and rider do not
get stuck and/or become unstable.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
B. ARMRESTS
WARNING
Armrests detach and will not bear the weight of this chair.
1. NEVER lift this chair by its armrests. They may come loose or
break.
2. Lift this chair only by non-detachable parts of the main frame.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
C. CUSHIONS AND SLING SEATS
WARNING
1. Zippie sling seats and standard foam cushions are not designed for
the relief of pressure.
2. If you suffer from pressure sores or if you are at risk that they will
occur, you may need a special seat system or a device to control
your posture. Consult your doctor, nurse or therapist to find out if
you need such a device for your well-being.
3. Seat slings are not intended to be used as a direct seating surface.
A cushion or other seating surface should be placed on the sling
before use.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
D. FASTENERS
WARNING
Many of the screws, bolts and nuts on this chair are special high-strength
fasteners. Use of improper fasteners may cause your chair to fail.
1. ONLY use fasteners provided by a Sunrise Medical authorized
dealer (or ones of the same type and strength, as indicated by the
markings on the heads).
2. Over- or under-tightened fasteners may fail or cause damage to
chair parts.
3. If bolts or screws become loose, tighten them as soon as you can.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
E. FOOTRESTS
WARNING
1. At the lowest point, footrests should be AT LEAST 2 inches off the
ground. If set too LOW, they may “hang up” on obstacles you can
expect to find in normal use. This may cause the chair to stop sud-
denly and tip forward.
2. To Avoid A Trip Or Fall When You Transfer:
a. Ensure your feet do not “hang up” or get caught in the space
between the footrests.
b. Avoid putting weight on the footrests, as the chair may tip for-
ward.
c. Footrests should be swung out of the way or removed whenever
entering or exiting the wheelchair.
3. NEVER lift this chair by the footrests. Footrests detach and will not
bear the weight of this chair. Lift this chair only by non-detachable
parts of the main frame.
4. Never use the footrests of the chair to open doors, this may cause
them to fail prematurely, and create an unsafe situation.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
F. PNEUMATIC TIRES
WARNING
Proper inflation extends the life of your tires and makes your chair easier
to use.
1. Do not use this chair if any of the tires are under- or over-inflated.
Check weekly for proper inflation level, as listed on the tire side-
wall.
2. Low pressure in a rear tire may cause the wheel lock on that side
to slip and allow the wheel to turn when you do not expect it.
3. Low pressure in any of the tires may cause the chair to veer to one
side and result in a loss of control.
4. Over-inflated tires may burst.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
Recommended
Pressure or Pressure
Range
Tires
Zippie TS
kPa PSI
Pneumatic (12-in) x 270 40
Pneumatic (16-in) x 240 35
Pneumatic (20-in) x 448 65
Pneumatic (22-in) x 448 65
Pneumatic (24-in) x 517 75
High Pressure Clincher (24-in) x 758 110

MK-100208 RevB 13
ZIPPIE TS VII. WARNINGS: COMPONENTS AND OPTIONS
A
11
G. POSITIONING BELTS (OPTIONAL)
WARNING
The positioning belt is predominately used to support your posture. It can
also be used to limit slipping and/or sliding that you might experience when
the chair is in motion. The positioning belt is not a transit rated safety belt
and should not be used in the place of a seat belt while being transported
in a motor vehicle. Improper use of positioning belts may cause severe
injury or death. If you use a positioning belt, ensure you follow the recom-
mendations in this section:
1. Ensure the rider does not slide down in the wheelchair seat. If this
occurs, the rider may suffer chest compression or suffocate due to
pressure from the belts.
2. The belts must be snug, but must not be so tight that they interfere
with breathing. You should be able to slide your open hand, flat,
between the belt and the rider.
3. A pelvic wedge or a similar device can help keep the rider from
sliding down in the seat. Consult with the rider’s doctor, nurse or
therapist to find out if the rider needs such a device.
4. Use positioning belts only with a rider who can cooperate. Ensure
the rider can easily remove the belts in an emergency.
5. NEVER use positioning belts
a. As a patient restraint. A restraint requires a doctor’s order.
b. On a rider who is comatose or agitated.
c. As a motor vehicle restraint. In an accident or sudden stop the
rider may be thrown from the chair. Wheelchair seat belts will
not prevent this, and further injury may result from the belts or
straps.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
H. PUSH HANDLES (OPTIONAL) 11
WARNING
When you have an attendant, ensure that this chair has push handles or
stroller handles (A).
1. Push handles provide secure points for an attendant to hold the
rear of this chair, to prevent a fall or tip-over.
2. Check to ensure push handle grips will not rotate or slip off.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
I. QUICK-RELEASE AXLES
WARNING
1. Do not use this chair UNLESS you ensure that both quick-release
rear axles are locked.
2. An axle is not locked until the quick-release button pops out fully.
3. An unlocked axle may come off during use, resulting in a fall, tip-over
or loss of control and cause severe injury to the rider or others.
4. Quick-release axles should be periodically cleaned and inspected for
function and signs of wear or bending. Replace as necessary.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
J. REAR WHEELS
WARNING
A change in set-up of the rear wheels will affect the center of balance of
your chair.
1. The farther you move the rear axles FORWARD, the more likely it
is that your chair will tip over backward.
2. Consult your health care provider to find the best rear axle set-up for
your chair. Do not change the set-up UNLESS you consult your health
care provider first.
3. Adjust the rear wheel locks after you make any change to the rear
axles.
a. If you fail to do so, the wheel locks may not work.
b. Ensure lock arms embed in the tires at least 1/8 inch when
locked.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
K. REAR WHEEL LOCKS
WARNING
Rear wheel locks are NOT designed to slow or stop a moving wheelchair.
Use them only to keep the rear wheels from rolling when your chair is at
a complete stop.
1. NEVER use rear wheel locks to try to slow or stop your chair when
it is moving. Doing so may cause a fall or tip-over
2. To keep the rear wheels from rolling, always set both rear wheel
locks when you transfer to or from your chair.
3. Low pressure in a rear tire may cause the wheel lock on that side
to slip and may allow the wheel to turn when you do not expect it.
4. Ensure lock arms embed in tires at least 1/8 inch when locked. If
you fail to do so, the locks may not work.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.

MK-100208 RevB
14
ZIPPIE TS VII. WARNINGS: COMPONENTS AND OPTIONS
L. MODIFIED SEAT SYSTEMS
WARNING
Use of a seat system not approved by Sunrise may affect or interfere with
other parts of the chair. This may cause the chair to tip over.
1. Do not change the seat system of your chair UNLESS you consult
your Sunrise Medical authorized dealer first.
2. Use of a seating system not approved by Sunrise may affect the fold-
ing mechanism of this chair.
3. Use of a seating system not provided by Sunrise is prohibited for
transit use.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
M. SEAT AND BACK UPHOLSTERY
WARNING
1. Replace worn or torn fabric of seat and seat back as soon as you
can. If you fail to do so, the seat or seat back may fail.
2. Sling fabric will weaken with age and use. Look for fraying, thin
spots, or stretching of fabrics especially at edges and seams.
3. “Dropping down” into your chair will weaken fabric and result in
the need to inspect and replace the seat more often.
4. Be aware that laundering or excess moisture will reduce the flame
retardation qualities of the fabric.
5. If Tension Adjustable upholstery is present, loosen straps or remove
upholstery prior to folding or unfolding the chair.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
N. POWER DRIVE
WARNING
Do not install a Power Drive on any Zippie wheelchair that has
not been approved by Sunrise Medical.
1. It will affect the center of balance of your chair and may cause a fall
or tip-over.
2. It will alter the frame and void the warranty.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
O. DYNAMIC BACKREST
WARNING
Do not use any Dynamic Backrest setup other than what was
provided by Sunrise Medical with your original chair.
1. It will affect the center of balance of your chair and may cause a fall
or tip-over.
2. It will alter the frame and void the warranty.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
P. ANTI-TIP RECEIVERS
WARNING
The anti-tip receivers are designed to move with the axle loca-
tion and are assembled in our manufacturing facilities.
1. Do not attempt to change the location of the anti-tip receivers, or
remove them UNLESS you consult your Sunrise Medical authorized
dealer first.
2. Use of a anti-tip system not approved by Sunrise may affect the cen-
ter of gravity of the chair and lead to a fall or tip-over.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.

VIII. USE AND MAINTENANCE
MK-100208 RevB 15
ZIPPIE TS
WARNING
The owner of this chair is responsible for ensuring that it has been set up
and adjusted by a trained service professional under the advice of a health
care provider. The chair may require periodic safety checks or certain tool-
free adjustments that may be performed by the owner, caregiver, or Sunrise
Medical authorized dealer if desired. Always use parts and/or accessories that
have been recommended or approved by Sunrise Medical when servicing this
chair.
A. INTRODUCTION
1. Proper maintenance will improve performance and extend the use-
ful life of your chair.
2. Clean your chair regularly. This will help you find loose or worn
parts and make your chair easier to use. You will need a mild deter-
gent solution and plenty of cleaning rags.
3. If discovered, repair or replace loose, worn, bent or damaged parts
before using the chair. ALWAYS be sure to use parts and/or
accessories that have been recommended or approved by Sunrise
Medical.
4. To protect your investment, have all major maintenance and repair
work done by your Sunrise Medical authorized dealer.
5. Inspect and maintain this chair strictly per the Safety Checklist.
6. If you detect a problem, ensure you order parts, or have service,
and repair work done at your Sunrise Medical authorized dealer
before use.
7. At least once per year, have a complete inspection, safety check,
and service of your chair made by a Sunrise Medical authorized
dealer.
B. CRITICAL SAFETY CHECKS
1. Tire Air Pressure
Check air pressure in pneumatic tires at least ONCE PER WEEK.
The wheel locks will not grip properly if you fail to maintain the air
pressure shown on tire sidewall.
2. Axles and Axle Sleeves
When checking axles and axle sleeves every six months, ensure they
are clean and tight. Loose sleeves will damage the axle plate and will
affect performance.
C. CLEANING TIPS
1. Paint Finish
a. Clean the painted surfaces with mild soap or detergent at least
once a month.
b. Protect the paint with a coat of non-abrasive auto wax every
three months.
2. Axles and Moving Parts
a. Clean around axles and moving parts WEEKLY with a slightly
damp (not wet) cloth.
b. Wipe off or blow away any fluff, dust or dirt on axles or moving
parts.
3. Upholstery
a. Hand-wash (machine washing may damage fabric).
b. Drip-dry only. DO NOT machine dry as heat will damage fabric.
4. Basic Maintenance Materials available at local store
a. Tire Pump
b. Tire Pressure Gauge
c. Clean rags or cotton cloth
d. Teflon-based Lubricant
e. Mild Detergent
NOTE– You do not need to grease or oil the chair.
Weekly 3 Months 6 Months Annually
RTire inflation level
RWheel locks
RVisually check for loose hardware
RArmrests
RAxle and axle sleeves
RQuick-release axles
RWheels, tires and spokes
RCasters
RAnti-tip tubes
RFrame and crossbrace
RUpholstery
RService by Sunrise Medical authorized
dealer
Safety and Function Check
RRRREnsure tire pressure is correct
and equal in both rear tires and front
caster tires, if pneumatic.
RRRREnsure all nuts and bolts are tight.
RREnsure all spokes and nipples are tight
on radial spoke wheels.
RUse Tri-Flow Lubricant (Teflon®-
based) between frame connections and
parts.
RRRRCheck for proper caster fork
adjustment. See instructions for
caster fork adjustment.
Symptom Left turn in chair Right turn in chair Looseness in chair Sluggish turning Squeaks and rattles Caster flutter
Solution
E. TROUBLESHOOTING CHART
D. SAFETY CHECKLIST
NOTE– The user or caregiver should perform these weekly and monthly
checks to maintain the safety of their chair. If an item is not
working properly, please contact your Sunrise Medical authorized
dealer.

MK-100208 RevB
16
ZIPPIE TS VIII. USE AND MAINTENANCE
F. TO MOUNT AND REMOVE REAR WHEELS 12 13
WARNING
Do not use this chair UNLESS you ensure both quick-release axles are locked. An unlocked axle may come
off during use and cause a fall.
1. To Install Wheel
a. Depress quick-release button (A) fully. This will release tension on ball bearings at other end.
b. Insert axle (B) through hub of rear wheel.
c. Keep button (A) depressed as you slide axle (B) into axle sleeve (C).
d. Release button to lock axle in axle sleeve. Adjust axle if it does not lock.
e. Repeat steps on other side.
NOTE–The axle is not locked until the quick-release button pops out fully (A). Check that the axle is locked
by pulling on the wheel in the direction of the axle.
2. To Remove Wheel
a. Depress quick-release button (A) fully.
b. Remove wheel by sliding axle (B) completely out of axle sleeve (C).
c. Repeat steps on other side.
G. WHEEL LOCKS 14
WARNING
Wheel locks are installed at Sunrise and should be adjusted by your qualified service person.
Inspect wheel locks weekly per the maintenance chart. Do not use your chair UNLESS you ensure both
wheel-locks can fully engage. A wheel-lock that is not correctly adjusted may allow your chair to roll, or turn
unexpectedly.
Wheel-locks must be adjusted after ensuring the tires have the correct air pressure. When fully engaged, the
arm should be imbedded into the tire at least 1/8-in (D) to be effective.
If you find the wheel locks have slipped or are not working correctly contact your Sunrise Medical authorized
dealer for proper adjustment.
H. HUB LOCKS 15
WARNING
To operate Hub Lock
1. To lock rear wheels, press button (E). Lever (F) will flip outward.
2. To unlock wheels, press lever (F) back down until button (E) pops back out. Each lever operates one
side of the chair. To fully lock chair, both buttons must be pushed.
NOTE - Do not engage hub lock when chair is in motion.
12
13
A
15
14
F
E
C
B
D

I. ANTI-TIPS 16 17 18
Sunrise Medical recommends anti-tip tubes for all wheelchairs.
1. Inserting Anti-Tip Tubes Into Receiver
a. Press the rear anti-tip release pin (A) on the anti-tip tube so that both release pins are drawn inside.
b. Insert the anti-tip tube into the receiver (B).
c. Turn the anti-tip tube down until release pin is positioned through the receiver mounting hole.
d. Insert second anti-tip tube the same way.
2. Adjusting Anti-Tip Tube Wheel
The anti-tip tube wheels may have to be raised or lowered to achieve proper clearance 1 1/2-in to 2-in.
a. Press the anti-tip wheel release pin (C) so that the release pin is drawn inside.
b. Raise or lower to one of the three predrilled holes.
c. Release pin.
d. Adjust the second anti-tip tube wheel the same way. Both wheels should be at exactly the same
height.
3. Turning Anti-Tip Tubes Up
Turn anti-tip tubes up when being pushed by attendant, overcoming obstacles or climbing curbs.
a. Press the rear anti-tip tube release pin (A).
b. Hold pin in and turn anti-tip tube up. (Fig. 18)
c. Release pin and ensure the anti-tip is locked in place.
d. Repeat these steps with second anti-tip tube.
J. SINGLE POST HEIGHT ADJUSTABLE ARMREST 19
Sunrise Medical offers several different types of armrests: Fixed, wwing-away, and Flip-back armrests. Flip-
back armrests can be detached or can flip back to allow lateral transfers. They are height adjustable (1-in
increments) by flipping the adjustment lever and moving the armrest pad (1) up or down to the desired
height.
1. Basic Installation
a. Slide the outer armpost (4) into the receiver mounted to the wheelchair frame.
b. The armrest should lock into place.
2. Height Adjustment
a. Release the upper securing lever (2).
b. Slide armpad (1) up or down to desired height.
c. Return lever (2) to locked position.
3. Removing Armrest
a. To remove, grasp the unlocking lever (3) and pull up on the armrest.
4. Replacing Armrest
a. Slide armrest back into receiver.
b. Ensure that the unlocking lever (3) returns to the locked position against armpost.
VIII. USE AND MAINTENANCE
ZIPPIE TS
17
MK-100208 RevB
1. Armrest pad
2. Height release lever
3. Release lever
4. Outer armpost
5. Transfer bar
6. Side panel
7. Receiver
8. Receiver adjustment hardware
4
3
6
2
5
8
7
19
1
17
C
18
16
B
A
12-in and
16-in
wheels
18-in to 24-in
wheels

ZIPPIE TS
18 MK-100208 RevB
K. Z-FINITY™FOOTREST SYSTEM (Option) 20 21
With the Z-finity footrest system, Sunrise Medical offers either a single Flip-up Footplate (A), or dual foot-
plates (B) that are able to accommodate all of the possible heights and adjustment angles that the rider may
require for their comfort and support.
L. SWING IN/OUT HANGERS/FOOTRESTS 22
Exterior Mount (60°, 70º, 80°), Front Mount (70º, 80°,90°)
1. Installation
a. Place swing-in/swing-out pivot saddle into the receiver (C) on front frame tube with the footrest
facing inward or outward from the frame.
b. Rotate the footrest inward until it locks into place on locking plate (D).
2. Removal
a. To remove footrest, release latch (E) by pulling lever upward or pushing lever downward.
b. Rotate footrest inward or outward and lift.
M. HEAVY-DUTY, LIFT-OFF FOOTRESTS (optional) 23
1. Installation
Slide pivot saddle (F) over receiver (G) on front frame tube until it locks into place.
2. Removal
To remove footrest, push release latch (H) while lifting up footrest from receiver.
N. ARTICULATING / ELEVATING LEGREST (optional) 24
1. Installation or Removal
To install or remove Articulating Legrest (ALR) see instructions for Swing-away Footrest installation.
2. Elevation Adjustment
a. To raise legrest, lift to desired position. Legrest will automatically lock in place.
b. To lower legrest, while seated in chair, press release lever ( I ) down and lower legrest to desired
position. Legrest will automatically lock in place.
VIII. USE AND MAINTENANCE
21
20
A
B
22
C
E
D
23
24
F
I
Articulating Legrest shown
G
H

O. FOLDING AND UNFOLDING 25
WARNING
Possible pinch point! BE CAREFUL.
NOTE– Only chairs with cross brace assembly will fold.
1. To fold the chair, remove the seat and back.
2. Pull the cross brace strap (A) up.
3. Press the side frames together firmly.
4. To open the chair, extend fingers and apply even pressure with palm of hand directly on cross brace
until it is fully extended.
5. Replace the seat and back.
6. To avoid pinching, be careful when folding or unfolding a chair.
NOTE – Ensure that footrests are flipped down and locked prior to use.
P. INTEGRATED STROLLER HANDLES 26
Positioning Swing-Away Adjustable Stroller Handles (option)
Loosen push handle (B) by pushing the black button (C). You can then raise or lower stroller handle to
desired position.
NOTE - For easy storage and portability, push handles will swing in and stroller handles fold flat.
Q. BACKREST 27 28
Note– Zippie series wheelchairs are shipped with the backrest in a folded position.
1. Folding the backrest
a. For easier storage and transport, locate the backrest release pin lever (D) on both sides and pull up
on the levers while pushing the backrest forward.
2. Unfolding the backrest
a. To secure the backrest in a riding position, lift by the handles to an upright position. When secured,
the backrest release pin will lock into place.
NOTE - For easy storage and portability, push handles should fold flat and not interfere with folding.
NOTE– Zippie series wheelchairs are shipped with the backrest in a folded position.
MK-100208 RevB 19
ZIPPIE TS VIII. USE AND MAINTENANCE
26
C
B
28
25
A
27
D

MK-100208 RevB
20
ZIPPIE TS
R. STORAGE TIPS
1. Store your chair in a clean, dry area. If you fail to do so, parts may rust or corrode.
2. Before using your chair, ensure it is in proper working order. Inspect and service all items on the
“Maintenance Chart”.
3. If stored for more than three months, have your chair inspected by a Sunrise Medical authorized deal-
er before use.
S. HYGIENE MEASURES WHEN BEING RE-USED
1. Prior to the wheelchair being re-used, it must be carefully prepared. All surfaces which come into con-
tact with the user must be treated with a disinfection spray.
2. To do this, you must use a disinfectant as authorized/recommended in your country, for rapid alco-
hol-based disinfection for medical products and medical devices, which must be disinfected quickly.
3. Please be aware of the manufacturer’s instructions for the disinfectant you are using.
4. In general, a complete disinfection cannot be guaranteed on seams. We therefore recommend that
you dispose of seat and back slings to avoid micro-bacterial contamination with active agents according
to your local infection protection law.
T. CHECK-OUT
After the wheelchair is assembled and adjusted, it should roll smoothly and easily. All accessories should also
perform smoothly. If you have any problems, follow these procedures:
1. Review the set-up and check-out sections to ensure chair was properly prepared.
2. Review troubleshooting guide.
3. If your problem persists, contact your Sunrise Medical authorized dealer. If you still have a problem
after contacting your Sunrise Medical authorized dealer, contact Sunrise Medical customer service. See
the introduction page for details on how to contact your Sunrise Medical authorized dealer or Sunrise
Medical customer service.
VIII. USE AND MAINTENANCE