SuperATV RBG-P-RZRXPTS User manual

© 2018 SuperATV.com. All Rights Reserved. IN-RBG-P-RZRXPTS / IN-RBG-P-RZR1K-004 10/5/2018
INSTALLATION INSTRUCTIONS
(kit contents on following pages)
Item Description
A Upper
B Lower
C Mount x 2
D Clamp x 2
E End Cap x 2
F Alignment Washer x 2
A
B
C
D
F
D
C
F
2753 Michigan Road • Madison, Indiana 47250 • 855-743-3427
Thank You
For Choosing
Read instructions and view illustrations before beginning.
Need help with your installation?
www.superatv.com
8:00am - 9:00pm EST M-Th
8:00am - 7:00pm EST Friday
9:00am - 2:00pm EST Saturday
[e-mail]
1-855-743-3427
E
Polaris RZR XP®Turbo S
Polaris RZR XP®1000 (2019)
Rear Brush Guard:

2IN-RBG-P-RZRXPTS/ IN-RBG-P-RZR1K-004
(kit contents continued)
4x M10 Lock Washer
Separate Clamps (D) and set aside.
2x M10-1.50 x 80mm Lg. FHCS
M12-1.75 x 30mm Lg. BHCS2x
M12-1.75 Nylock Nut
4x
M12-1.75 x 80mm Lg. FHCS
4x
M10-1.50 x 30mm Lg. FHCS2x
4x M10 Flat Washer
Drill Guide
Spacer4x
use only if stock RSL’s are installed
Liability Statement
SuperATV’s®products are designed to best fit user’s ATV/UTV under stock conditions. Adding, modifying, or fabricating any factory or aftermarket parts will void any warranty
provided by SuperATV®and is not recommended. SuperATV’s® products could interfere with other aftermarket accessories. If user has aftermarket products on machine, contact
SuperATV®to verify that they will work together.
Although SuperATV®has thousands of satisfied customers, user should be aware that installing lift kits, long travel, or suspension kits, tires, etc. will change the ride of machine
and may increase maintenance and part wear. Operating any off-road machine while, or after, consuming alcohol and/or drugs increases risk of bodily harm or death. No
warranty or representation is made as to this product’s ability to protect user from severe injury or death. SuperATV®urges operators and occupants to wear a helmet and
appropriate riding gear at all times.
By purchasing and installing SuperATV®products, user agrees that should damages occur, SuperATV®will not be held responsible for loss of time, use, labor fees, replacement
parts, or freight charges. SuperATV®, nor any 3rd party, will not be held responsible for any direct, indirect, incidental, special, or consequential damages that result from any
product purchased from SuperATV®. The total liability of seller to user for all damages, losses, and causes of action, if any, shall not exceed the total purchase price paid for the
product that gave rise to the claim.
SuperATV®will warranty only parts provided by SuperATV®. Any damage or problems with OEM housings, bearings, seals, or other manufacturers’ products will not be covered
by SuperATV®. SuperATV®parts and products are not warrantied if item was not installed properly, misused, or modified.
Installing, adding, modifying, or fabricating any factory or aftermarket product to your ATV/UTV may violate certain local, state, and federal laws. Be advised that laws vary
depending on town, city, county, state, etc. Use of certain products on public streets, roads, or highways may be in violation law. The Buyer is solely and exclusively legally and
personally responsible for any violation of the law by the installation or use of the product. You must abide by all local, state, and federal laws, including but not limited to vehicle
safety, traffic laws, and ordinances. It is your responsibility to know the laws and how they apply to you.
The Buyer is responsible to fully understand the capability and limitations of his/her vehicle according to manufacturer specifications, warnings and instructions and agrees to
hold SuperATV®harmless from any damage resulting from failure to adhere to such specifications, warnings and/ or instructions. The Buyer is also responsible to obey all
applicable federal, state, and local laws and ordinances when operating his/her vehicle while using this product, and the Buyer agrees to hold SuperATV®harmless from any
violation thereof.

3IN-RBG-P-RZRXPTS/ IN-RBG-P-RZR1K-004
Keep all components removed from machine.
- Remove stock Facia.
Fascia
- Remove Plate and Radius Arms hardware.
Plate and Radius Arms hardware
(SuperATV RSL’s installed) (Passenger Side)

4IN-RBG-P-RZRXPTS/ IN-RBG-P-RZR1K-004
(Driver Side)
- remove stock bolt
- insert Drill Guide into stock hole
- secure Drill Guide with stock bolt
- insert drill bit into Drill Guide and drill through Frame
- hole must be large enought to accept Ø10mm bolt
- remove Drill Guide and reinstall stock bolt
- repeat for opposite side
Drill Guide
stock bolt

5IN-RBG-P-RZRXPTS/ IN-RBG-P-RZR1K-004
(SuperATV RSL’s installed; do not install Spacers)
- Secure Lower (B) to Frame with hardware shown.
(Passenger Side)
B
4 each
M12 Nut
M12 x 80mm
Spacer
If stock RSL’s are installed, Spacers must
be installed so they are against Frame.
RSL’s install against
Lower (B)
B

6IN-RBG-P-RZRXPTS/ IN-RBG-P-RZR1K-004
- Install Mounts (C) to Upper (A) with hardware shown.
- Install End Caps (E) to Upper (A) with hardware shown.
A
CC
E
M10 Lock
Washer
M10 x 30mm
M12 x 30mm
(Passenger Side)

7IN-RBG-P-RZRXPTS/ IN-RBG-P-RZR1K-004
A
B
D
- Reinstall Fascia.
- Secure Upper (A) and Alignment Washer (F) to Frame with hardware shown.
- Join Upper (A) and Lower (B) with Clamps (D).
M10 Lock
Washer
M10 x 80mm
C
A
F
(Passenger Side)

8IN-RBG-P-RZRXPTS/ IN-RBG-P-RZR1K-004
- Align to machine and tighten all hardware completely.