Swiss Madison SM-WC324 User manual

®
Swiss Madison
®
INSTALLATION
INSTRUCTIONS
Back-to-Wall Concealed Tank System
SM-WC324
www.swissmadison.com | 1-434-623-4766 | [email protected]
Share your pictures for a feature
using #SwissMadison

—1 —
Prior to Installation:
· We recommend a professional contractor. Customer is responsible for any damage that
may occur during installation.
If you have any questions or concerns please contact us:
1-434-623-4766
[email protected]
General Recommendations: Read installation and maintenance instructions thoroughly before installation.
Be sure to use proper tools and always wear proper personal safety accessories for your protection.
· Read instructions thoroughly.
· Remove existing toilet.
· Be sure to properly bleed all air from the piping system, trapped air can cause
damage to the flushing system and toilet bowl.
· Additional floor and wall preparations may be necessary to avoid damage to the product
· Observe all local plumbing codes.

Thank you for purchasing a Swiss Madison Concealed Tank System.
We appreciate your business and know you will enjoy your product for many years to come.
If you have any questions or require assistance we would be happy to help,
please contact us at 1-434-6234766 or [email protected].
Thank you for your purchase!
www.swissmadison.com
To learn more about our products, please visit:
Sincerely,
The Swiss Madison Team
—2 —

The step-by-step guidelines in the installation instructions are a general reference for installing a Swiss Madison Concealed Tank System.
Should there be any discrepancies, Swiss Madison cannot be held liable.
It is recommended to install all Swiss Madison products by hiring a licensed professional
—3 —
CONCEALED TANK SYSTEM ROUGH DIMENSIONS
1. Read the complete instruction manual before beginning installation.
2. Confirm that your model will fit in intended location and plumbing fixtures are
located where legally required before beginning installation.
3. Not all drawings on this manual are drawn to scale. Please refer to the model chart.
4. Two people are recommended to install and move this product.
NOTE: Specialized tools may be necessary to install a Swiss Madison Concealed Tank.
SUGGESTED TOOLS AND MATERIALS
Flat FileDrill LevelTape MeasurePencilSaftey Goggles WrenchHacksaw Plumbers Grease
x
NPT
0
24 
18 
max - 5 
2 
3 
21 
28 
23 
39 
”
3 

CONCEALED TANK SYSTEM INSTALLATION INSTRUCTIONS
—4 —

CONCEALED TANK SYSTEM INSTALLATION INSTRUCTIONS
—5 —
1a. 1b.
1
3
2
3
1 2
“Click” “Click”
1. Fasten Mounts (if fastening to studs)
· Adjust clips then fasten carrier to studs or wall framing.
· Ensure frame is flush and level before fastening.

CONCEALED TANK SYSTEM INSTALLATION INSTRUCTIONS
—6 —
1. Fasten Mounts (if fastening to wall)
· Adjust clips then fasten carrier to studs or wall framing.
· Ensure frame is flush and level before fastening.
A
B
1 2 3
13
1 1
Ø10

CONCEALED TANK SYSTEM INSTALLATION INSTRUCTIONS
—7 —
1000mm
0
HX
L=X-H
L(max.150mm)
1
3
2
2
3
1
2. Cut Pipe
· Measure and cut pipe according to your toilet.
· Make sure to measure the sub floor and finished floor measurements before cutting to have the
correct center.
· Once pipe is cut, remove any burrs.
3. Attach Pipe
· Apply grease before sliding on pipe.
· Install pipe then put on dust cap to prevent debris from entering the pipe.

CONCEALED TANK SYSTEM INSTALLATION INSTRUCTIONS
—8 —
1
2
3
1
2
1
1
2
1
2
3
4. Remove Plate
· Remove plate attach to water connection.
5. Attach Water Connection
· Hold the shut-off valve stationary while tightening water connection.
· Install locking nut as shown.

CONCEALED TANK SYSTEM INSTALLATION INSTRUCTIONS
—9 —
2
3
1
1
1
2
12
a.
b.
c.
d.
6. Flush Debris
· After attaching water connection to shut-off valve, undo the other side of the hose.
· Turn on valve to flush any debris before installing the actuator.
7. Reconnect Water Supply
· After flushing debris, reconnect the water supply hose.