Sylvac S Dial Mini User manual

INSTRUCTIONS
MODE D’EMPLOI
BEDIENUNGSANLEITUNG
MANUALE D’USO
INSTRUCCIONES DE USO
E
S
D
F
I
MINI DIAL GAUGE
MINI COMPARATEUR
MINI MESSUHR
MINI COMPARATORE
MINI COMPARADOR

Installing and replacing the battery
(or Power cable)
Mise en place et remplacement de la
batterie (ou câble Power)
Einbau und Austausch von Batterie
(oder Netzkabel)
Installazione e sostituzione della batteria
(o del cavo di alimentazione)
Colocación y sustitución de la batería
(o cable Power)
Battery / batterie / Batterie / batteria / bateria: lithium 3V, type CR2032

4
E

5
E
Description
1. MODE button
2. SET button
3. “Favourite ” button
4. Clamping shaft Ø8 or 3/8”
5. Lifting cap (depends on version)
6. Contact point Ø2/ M2.5 or 4-48-UNF
7. Slot for battery or Power cable
8. Dovetail xing
9. Measurement units (mm/ INCH)
10. +/ - Indicator
11. Low battery
12. Preset Mode
13. MIN/MAX/DELTA mode
14. Multiplication factor
15. Hold measured value
16. Analog scale range
17. Keypad lock
18. 6 digits display
19. Bluetooth
®active
20. Send data
21. Analog display

SET
MODE
6
E1. Operating features of the instrument
- The instrument has two operating modes: basic functions (direct access) and advanced functions. In addition
to the conguration functions, you can access to MIN, MAX and DELTA (TIR) mode, plus input of multiplication
factor other than 1:1 (see chaps. 3 and 4).
- The «favourite» key gives direct access to the function used most often (see chap. 6).
- Sets a Preset value, resets the MIN/MAX mode, veries a selection, and controls switching o󰀨 the instrument.
By default, SIS mode enables automatic switch-o󰀨 with no loss of origin (see chap. 7).
- Personalising the functions
It is possible to activate or de-activate certain functions of the instrument via RS232 (see chap. 9).
- Data transmission parameters
4800Bds, 7 bits, even parity, 2 stop bits.
2. Start Press a button.
For a Bluetooth
®connection (see chap. 5).

MODE
MODE
SET
7
E
3. Basic functions
Each short press on gives direct access to the basic functions:
Inputting a Preset value
MIN, MAX measurement
DELTA (TIR)
Bluetooth®Enable / disable,
reset Bluetooth®module
or display its MAC address.
next digit 0...9 save PRESET

MODE MODE
MODE
MODE
SET
8
E4. Advanced functions
Prolonged pressure (>2s) on gives access to the advanced functions. Then, each short press on accesses
the required function:
Unit selection (mm or inch)
Choice of resolution 0.01 / 0.001
(only for 0.001mm version)
Choice of measurement direction
(positive or negative direction)
Multiplication factor, enable or disable multiplication factor
(value can be modied if On is conrmed by button)
Input of multiplication factor, next digit 0....9
save MULT

SET
9
E
........ continuation
Automatic switch-o󰀨 mode
MAn = disabled, Auto = active
(after 10 min. by default).
Bluetooth® prole selection.
(see chap. 5 for details)
The + sign indicates the currently active prole.
Keypad lock Only the favourite key remains active.
(to unlock the keypad, press for 5 sec).
Selection of the analog scale range :
- AnA 1 : 1 scale = 1 digit
- AnA 5 : 1 scale = 5 digits
- AnA 10 : 1 scale = 10 digits
- AnA OF : de-activate the analog scale
range

10
E5.
Bluetooth
®configuration
The connection procedure has been designed to be simple and is signalled by the following three states:
° Symbol o󰀨.............. disconnected mode
° Symbol blinking...... advertising mode
° Symbol on.............. connected mode
The following options can be selected to control the Bluetooth®module.
On Enable Bluetooth®module (start advertising mode).
OFF Disable Bluetooth®module (terminate active connection).
rESEt Clear pairing information.
MAC Display the MAC (Media Access Control) address.
Three Bluetooth® proles are available.
SIMPLE Prole without pairing (default).
PAIr Paired and secured prole.
HId Virtual keyboard mode (compatible with recent equipment without driver installation).

11
E
Connection:
1° Activate Bluetooth
®compatible software and hardware (Master : PC, Display Unit).
2° Start the instrument. By default the Bluetooth
®
module is active and the instrument is available for connection (advertising
mode).
3° If no connnection is established during the advertisement period reactivate the Bluetooth
®module using the bt / On menu.
4° Instrument is ready to communicate (connected mode.)
Only with paired profile:
Pairing with master is automatically done at rst connection.
To connect the instrument to a new master (new pairing), pairing information on the instrument must be cleared using the bt /
rESEt menu.
Note:
- Bluetooth® pairing information is cleared when the prole is changed.

12
E5.1
Bluetooth
®specifications
Frequency Band 2.4GHz (2.402 - 2.480GHz)
Modulation GFSK (Gaussian Frequency Shift Keying)
Max Output Power Class 3: 1mW (0dBm)
Range Open space: up to 15m
Industrial environment: 1-5m
Battery life
Continuous : up to 2 months - Always connected with 4 values /sec.
Saver : up to 5 months - The instrument sends value only when the position has changed.
Blind/Push : up to 7 months - Value is sent from the instrument (button) or requested from the
computer.
Other specications on the manufacturer’s website.

MODE
SET
13
E
6. Favourite key
The «favourite» key gives direct access to a predened function, and can be congured according to the needs of the
user. In order to assign a function to the «favourite» key, give a prolonged press on , and then select the required
function:
Validation of selection: By a prolonged press on or a short press on or .
Note:
- A function can also be assigned via RS232 using the command <FCT + Function No.> (FCT 0..9 A..F)
example : Toggle unit = <FCT7>, multiplication factor =<FCTA>.
Data
transmission
(default)
Hold display
Re-initialise
Min-Max-Delta
Zero reset
Recall Preset
Nor-Min-Max-
Delta
Bluetooth®ON-
OFF
mm – IN
0.01 ↔ 0.001
Measurement direction,
positive - negative
1:1 - N:1 factor
Analog display
No function

SET
SET
SET
MODE
>2s
SET
>4s
SET
14
E7. Switching off
The dial gauge goes automatically into stand-by if not used for 10 minutes, unless automatic switch-o󰀨 mode has been
turned o󰀨 (see Chap. 4, advanced functions).
Stand-by mode can be forced by a prolonged press (> 2 sec) on :
In stand-by mode, the value of the origin is retained by the sensor (SIS mode), and the instrument automatically restarts
with any movement of the measurement probe, RS command, Bluetooth®request or press on button.
The instrument can be switched o󰀨 completely for a long period of non-use, but this will necessitate a zero reset on restart
(the origin will be lost):
- Prolonged press (>4 sec) on :
8. Re-initialising the instrument
The initial instrument settings can be restored at any time by a prolonged press (>4 sec) simultaneously on and
until the message rESEt is displayed.

15
E
9. Personalising the instrument
Access to the functions of your instrument can be personalised, for more information see manufacturer’s website
(requires you to connect your instrument via Proximity or Power RS / USB cable, or Bluetooth
®).
Possibilities:
- Enable or disable the required functions.
- Modify access to the advanced functions (direct access).
10. Connecting the instrument
The instrument can be connected to a peripheral via a Proximity (RS or USB), Power (RS or USB) cable or Bluetooth
®.
See page 3 for connecting the Power cable.
Measured values can be transmitted and the instrument driven using predened commands (see chap. 11 for a list of
the main commands).

16
E11. List of the main commands
Selection and configuration Interrogation
CHA+ / CHA- Change measurement direction ? Current value?
CHA? Measurement direction?
FCT0 ...9...A...F Assign «favourite» function FCT? «favourite» function active?
MM / IN Change measurement unit UNI? Measurement unit active?
KEY0 / KEY1 Lock / unlock keypad KEY? Keypad locked?
MUL [+/-]xxx.xxxx Modify multiplication factor MUL? Multiplication factor?
PRE [+/-]xxx.xxx Modify preset value PRE? Preset value?
STO1 / STO0 Activate / de-activate HOLD STO? Status of HOLD function?
ECO1 / ECO 0 Activate / de-activate economic mode ECO? Current economic mode
LCAL dd.mm.yy Modify last calibration date LCAL? Date of last calibration?
NCAL dd.mm.yy Modify next calibration date NCAL? Date of next calibration?
NUM x...x (up to 20chars) Modify the instrument number NUM? Instrument number?
MIN /MAX /DEL /NOR Selecting MIN, MAX, Delta, Normal mode MOD? Active mode (MIN, MAX, Delta or Normal)?
CLE Re-initialisation of MIN, MAX or Delta SET? Main instrument parameters?
UNI1 / UNI0 Activate / de-activate change of units ID? Instrument identication code?
OUT1 /OUT0 Activate / de-activate contin. data transmission
ANA ON / ANA OFF Activate / de-activate the analog scale
FACT1/FACT5/FACT10 Range of the analog scale
Maintenance functions
PRE ON / PRE OFF Activate / de-activate Preset function BAT? Battery status (BAT1 = OK, BAT0 = low battery)
PRE Recall Preset OFF Switch-o󰀨 (wake up using a button or RS)
SET Zero reset RST Re-initialisation of the instrument
RES1 / RES2 Change of resolution SBY Put instrument in stand-by (SIS)
VER? Version No. and date of rmware
SBY xx xx number of minutes before stand-by
BT0/BT1 Activate / de-activate Bluetooth®module MAC? Bluetooth®MAC address ?
BTRST Clear pairing information

12. Specifications
Measurement range: 12.5mm 12.5mm
Resolution 0.01mm 0.001mm
Max error 10µm +1 digit 4µm
Repeatability: 2µm
Weight: 75g
Measurement force (standard) +20% : 0.5-0.9N 0.5-0.9N
Measurement force (protected) +20% : 0.6-1.3N 0.6-1.3N
Max. speed of travel: 1.7m/s
No. of measurements / second: up to 10 meas/s MIN/MAX mode: up to 20 meas/s
Measurement unit: metric/english (Inch)
Maximum Preset (10µm resolution): ±999.99 mm / ±39.9995 IN ±99.999 mm / ±3.99995 IN
Measurement system: Sylvac inductive system (patented)
Power: 1 x 3V lithium battery, type CR2032, 220mAh
Average battery life: 8’000 hours (with Bluetooth® enabled, see chapter 5.1)
Data output: RS232 compatible / Bluetooth®4.0 (see chapter 5)
Working temperature (storage): +5 to +40°C (-10 to +60°C)
Electromagnetic compatibility: as per EN 61326-1
IP rating (in accordance with IEC60529): IP 67
Fixing and space envelope: Ø8h6 (3/8’’), interchangable M2.5 (4-48-UNF) probe (as per DIN 878)
17
E

18
F

19
F
Description
1. Bouton MODE
2. Bouton SET
3. Bouton “Favoris”
4. Canon de xation Ø8 ou 3/8”
5. Bonnette de relevage (dépend de la version)
6. Touche à bille Ø2 /M2.5 ou 4-48-UNF
7. Logement batterie ou câble Power
8. Fixation sur queue d’aronde
9. Unité de mesure (mm/INCH)
10. Indicateur +/-
11. Batterie faible
12. Mode Preset
13. Mode MIN/MAX/DELTA
14. Facteur de multiplication
15. Gel de la valeur de mesure
16. Etendue échelle analogique
17. Verrouillage des boutons
18. A󰀩chage - 6 digits
19. Connexion Bluetooth
®
20. Envoi de données
21. Echelle analogique

SET
MODE
20
F
1. Les fonctionnalités de l’instrument
- L’instrument possède 2 modes de travail : fonctions de base (avec accès direct) et fonctions avancées.
En plus des fonctions de conguration, vous pouvez accéder au mode MIN, MAX et DELTA (TIR), ou à l’intro-
duction d’un facteur de multiplication (voir chap. 3 et 4).
- Le bouton «favori» permet d’attribuer un accès direct à la fonction principalement utilisée (voir chap. 6).
- Le bouton «SET» permet d’attribuer une valeur de Preset, de réinitialiser le mode MIN/MAX, de quittancer une
sélection, et de gérer l’extinction de l’instrument. Par défaut, le mode SIS permet l’extinction automatique sans
perte de l’origine (voir chap. 7).
- Personnalisation des fonctions
Vous avez la possibilité d’activer ou désactiver certaines fonctions de l’instrument par RS232 (voir chap. 9).
- Paramètres de transmission de données
4800Bds, 7 bits, parité paire, 2 stop bits.
2. Démarrer
Presser un bouton.
Pour une connexion Bluetooth
®(voir chap. 5).