Sylvac Fowler Ultra-cal II User manual

t
s:::::
.2
-
o
::::J
...
-
t
e
-
C)
c:
-
as
...
Q)
a.
o

SPECIFIC TIONS ND FUNCTIONS
Measuring range:
Resolution:
Accuracy:
Repeatability:
Maximum measuring speed:
Measuring units:
Measuring system:
Display:
Power:
Battery life:
Operating temperature:
Storage temperature:
Influence of humidity:
Data output:
Interface:
Jaws and body:
Weight:
NOTE:
Step
measuring face
depth: 0-6
step: 0-6 0-150 mm 0-150 mm
inside: 0-6 0-150 mm
outside: 0-6 0-150 mm
.0005 0.01 mm
.001 0.03 mm
.0005 0.01 mm
> 60 /sec. - > 1.5 m/sec.
inch/metric, switch able (true conversion)
non-contacting linear SYLVAC measuring system (patented)
LCD display, minus sign - ,5 digits with .185 /4.7 mm character height, small digit
5 and IN sign for inch measuring unit
one battery, 1.5 V., sylver oxyde (high drain), 190 mAh.
End of battery life warning by flashing display.
12 months of continuous use (reading constantly visible)
0° to + 40° C
- 20° to + 70° C
not important within 0 to 80% of relative humidity
serial
RS 232
hardened and ground stainless steel
145 grams
If the display does not operate correctly (display does not count or it is impossible
to reset to zero), remo e the battery (see page 6), wait 30 seconds and reinsert bat-
tery.
Do not use the digital caliper without its cap (on data output). This cap has to be
removed only in the event of the connection to an interface.
,-- __ Inside measuring jaws
r--- Positive locking screw
Wiper Scale
Zero setting
(zero setting at any position within the measuring range)
'------ INCH/METRIC change over
(true conversion)
Depth
measuring blade
Outside measuring jaws

SELECTION OF INCH OR METRIC RE DING
Close jaws, select inch or metric Example of metric reading
mode, press zero button key
INCH/Metric
ZERO SETTING ND ME SURING
While maintaining pressure on Move the jaw (3)
jaw (1) press button key for zero
display (2)
Outside measurements Inside measurements
Example of inch reading (last figure
no digit or small five)
Step measurements

PPLIC TIONS
Deviation from reference size (A reference size). Outside or inside measurement
Comparisons, e.g. between plug and hole
Measurement of wall thickness

PPLIC TIONS
Measurement of center distance between two identical holes
ME SURING IN PL CES WHERE RE DING IS DIFFICULT
Set zero (3) while main-
taining pressure on jaw (2)
2
Close jaws (5). Read result while main-
taining pressure on jaw (disregard
minus sign)

CHANGING OF BATTERIES
2 screws
remove the 4 screws
remove the housing
2 screws
y
-I :DDO ~-;UU.
l ~(\
I~---da~-~
VJery
Contact springs
•
remove the battery and replace
it
mount the housing
WARNING: sensitive contact
springs. Do not force the hous-
ing into position
locate first and than attach the
4 screws
It
Battery reference guide: 1.5 V., silver oxyde, high drain, 190 mAh.
UCAR 357
Ever-Ready 357 (UNION CARBIDE)
National WL 14
Seiko SB-B9
Mallory 0357 (10 L 14)
Bulova 228
Timex Typ J
IF owl r 1 F_r_e_d_V_ _F_o_w_le_r_C_o---' ,_I_ _c _
CHICAGO BRANCH OFFICE:
825 N. Cass Ave., Suite 310
Westmont, Illinois 60559
[phone]
MAIN OFFICE
66 Rowe Street
P.O. Box 48
Newton, Massachusetts 02166
[phone]
CABLE ADDRESS:
Precision· Auburndale
Telex 92 2435
LOS ANGELES BRANCH OFFICE:
5434 E. Washington Blvd.
Los Angeles, California 90040
[phone]