Sylvac S-Mike PRO User manual

Instruction manual
Manuel d’instruction
Handbuch
Manuele d’uso
Instrucciones de uso
S_Mike PRO

2
Force/Force/Messkraft/Forza/Fuerza
Measuring force adjustement
Only on model 0-30mm
Ajustage de la force de mesure
Uniquement pour modèle 0-30mm
Einstellbare Messkraft
Nur für Modell 0-30mm
Regolazione della forza di misurazione
Solo per il modello 0-30mm
Ajuste de la fuerza de medición
Solo para modelos de 0-30mm

EN
1. Maintenance
Store the instrument in a dry place to avoid corrosion of metal parts if
not used for a long time.
Do not press the movable key on the anvil: leave a gap of 1-2mm when
the instrument is not in use.
Do not use aggressive products (alcohol, trichloroethylene or other
aggressive liquids) to clean plastic parts.
Do not store the instrument in a place exposed to sunlight, heat or
humidity.
Important: in the event of liquid splashes, wipe off the metal parts
of the instrument to ensure proper mechanical operation and avoid
corrosion problems.

4
2. General description
The micrometer is equipped with a Smart Inductive Sensor (SIS)
which maintains the reference position even when the instrument is
in standby mode. Its non-rotating button principle enables rapid posi-
tioning. It features the following operating characteristics:
• Enter preset value.
• Change unit (mm / INCH).
• Measured value transmission via Proximity or Bluetooth®
connection (depending on model).
• Protection against dust ingress and liquid splashes (oil, water) to
IP67 (IEC 60529).
12 7
3 5 64
8
14
12
1511
10
13
9

EN
1. Measuring spindle
2. Anvil
3. Isolate plate
4. MODE button
5. Favourite button
6. SET button
7. Rotating thimble
8. Proximity connector
9. Battery cover
10. Low battery indicator
11. Value hold indicator
12. Data transfer indicator
13. Locking indicator
14. Bluetooth® indicator
15. Fmin mode indicator

6
3. Instrument features
The instrument has 2 operating modes: basic func-
tions (with direct access) and advanced functions.
In addition to the configuration functions, you can select the
HOLD function or activate the keyboard lock (LOC function). You
can also activate the FMIN function (see chap. 6).
The «favorite» button assigns direct access to the most
frequently used function (see chap. 10).
The «SET» button allows you to assign a preset va-
lue, quit a selection, and manage instrument switch-off.
By default, SIS mode enables automatic switch-off without loss of
origin (see chap. 11).
Customizing functions
You can activate or deactivate certain instrument functions via Power
RS/USB or Bluetooth® cables (see chap. 13).
Data transmission parameters
4800Bds, 7 bits, even parity, 2 stop bits.
SET
MODE
4. Start-up, initialization
Press a button.
The instrument displays «SET» to initialize the reference point. Return
the movable key to the anvil (or to a master gauge). Then press .
The instrument is now ready for use (check preset value, correct if
necessary and reset).
SET

EN
Next digit 0...9 save PRESET
PrE : Preset value input
bt : Bluetooth®. Activate/deactivate, reset Bluetooth® module or
display MAC address (depending on model).
5. Basic functions
Each short press gives direct access to basic functions:
MODE
SET MODE
MODE
SET MODE
MODE
SET
MODE
MODE
SET MODE
MODE
MODE
MODE
bt Off rESEt
SET
MAC On

8
6. Avanced functions
A long press (<2s) on accesses the advanced functions. Each short
press then accesses the desired function:
MODE
SET MODE
MODE
SET
MODE
Unit : Unit selection (mm or inch).
OFF : Automatic switch-off mode.
MAn : disabled. Auto : active (after 10min. by default).
bt.CFG : Bluetooth® profile selection (see chap. 9 for details). The + symbol
indicates the active profile (depending on model).
HoLd : Select On to activate display freeze when briefly pressing .
Loc : Keypad lock. Only the favorite key remains active (to deactivate keypad
lock, press for 5 sec).
FMin : Activate FMIN function (see chap. 7 for details)
MODE
SET
MODE
MODE
SET MODE
MODE
SET
MODE
Next digit 0...9 save FMIN
MODE
SET MODE
MODE
SET
MODE
MODE
SET MODE
Without any pressure (after 5s): return to measuring mode (15s for preset
entry)
OFF . MAn:Mode d’extinction automatique = désactivé,
Auto = actif (après 10min. par défaut)

EN
7. FMIN function (depends on model)
The high-speed micrometer features a spring-loaded spindle. This
construction ensures high repeatability, thanks to the constant force
in the measuring zone.
When the FMIN. mode is active, the minimum measuring value is auto-
matically stored and displayed.
The FMIN stroke value can be set by the user according to his needs
(0.010mm to 5.080mm depending on model).
Refer to chapter 6 to activate/deactivate or set the FMIN function.
Start measurement
Measurement
As long as the contact
points are in the FMIN
zone, the value displayed
remains unchanged.
If the contact points are
outside the FMIN range,
the value corresponding
to the actual spindle posi-
tion is displayed.
Example : Part Ø5.0mm Zone FMIN
5.225
5.000
DYNFMIN
DYNFMIN
DYNFMIN
FMIN
5.000
5.450

10
8. Proximity connection (Non-Bluetooth®
instrument only)
The instrument features a non-contact data output for direct connec-
tion to a PC or printer via a Proximity cable.
By default, a short press on the button transmits the current value.
The data transmission indicator is briefly displayed. Sending data can
also be requested by the peripheral device (see chap. 15. List of main
commands).
9. Bluetooth® configuration (Instrument
Bluetooth® only)
The connection procedure has been designed to be as simple as pos-
sible, and is distinguished by the 3 states below:
1. Symbol off.......... disconnected mode.
2. Symbol blink...... discovery mode.
3. Symbol on........ connected mode.
ThefollowingoptionscanbeselectedtocontroltheBluetooth®module.
On Activate Bluetooth® module (start discovery mode).
On Activate Bluetooth® module (start discovery mode).
OFF Deactivate Bluetooth® module (terminate active connection).
rESEt Clear Matching information.
MAC Display MAC (Media Access Control) address.
Three Bluetooth® profiles are available.
SIMPLE Unpaired profile (default).
PAIr Paired and secured profile.
HId Virtual keyboard mode (compatible with recent equipment
without driver installation).
Note:
Bluetooth® Matching information is deleted when the profile is
changed.
MODE
SET MODE

EN
Connection :
1. Ensure that the Bluetooth® compatible application and hardware
are active (PC, measurement unit).
2. Start the instrument. By default, the Bluetooth® module is active
and the instrument can be connected (discovery mode).
3. As soon as the instrument is detected, connection is automatic. If
the connection was not established while the instrument was in
discovery mode, reactivate the Bluetooth® module via the bt / On
menu.
4. The instrument is ready to transmit (connected mode)
Only with Matching profile : :
The instrument is automatically matched to the Central (PC) on first
connection.
To connect an instrument to a new Central (new pairing), the pairing
information must be deleted via menu bt / rESEt.
9.1. Bluetooth®specifications :
Core version Bluetooth®5
Frequency band 2.4GHz (2.402 - 2.480GHz)
Max. output power Class 3: 1mW (0dBm)
Classic range (default) Long range 4)
Range Open space
Industrial environment
up to 20m
2-6m
up to 80m
3-10m
Autonomy
Continuous 1
Saver 2
Blind/Push 3
up to 3 months
up to 6 months
up to 8 months
up to 2 months
up to 4 months
up to 6 months
1Continuous : Always connected with 4 values /sec
2Saver: Instrument sends value when position changes.
3Blind/Push: The value is sent from the instrument (button) or re-
quested by computer.
4 Long range: more information on the manufacturer’s website.

12
10. Favourite key
The «favorite» button provides direct access to a predefined
function, and can be configured according to the user’s needs.
To assign a function to the «favorite» button, press and hold (>2s) ,
then select the desired function:
MODE
SET MODE
Sending
data
(default)
Hold the
display
Zero setting
Racall of
preset
Bluetooth® ON-OFF
(depends on
version)
mm – IN
No function
Note:
The function assignment can also be made via RS 232,
with the command <FCT + Function No> (FCT 0..9 A..F)
example: Unit change = <FCT5>
Confirm selection :
Long press on or short press on or
MODE
SET MODE
MODE
SET
MODE
MODE
SET MODE
bt
no.F

EN
11. Switching off
The instrument automatically goes into stand-by mode after 10
minutes of non-use, unless the automatic switch-off mode is deac-
tivated (see chap.6 advanced functions).
You can force stand-by mode by pressing and holding (>2s) :
In stand-by mode, the original value is retained by the sensor (SIS
mode), and the instrument is automatically restarted by a movement
of the contact points or by RS command, or by pressing a button.
It is possible to switch the instrument off completely for long periods
of non-use, but this will require a reset at start-up (loss of origin):
Long press (>4s) on :
SET
SET
12. Resetting the instrument
At any time, it is possible to restore the instrument’s initial set-
tings, by simultaneously pressing and for a long time (>4s)
until the message rESEt is displayed.
SET
MODE
SET
MODE
>2s
SET
>4s
SET

14
13. Personnalisation of the instrument
It is possible to customize access to your instrument’s functions, for
more information see the manufacturer’s website (requires a connec-
tion to your instrument, via a Proximity cable, or Bluetooth®).
Options:
- Disable or enable desired functions.
- Modify access to advanced functions (direct access).
14. Instrument connection
The instrument can be connected to a peripheral via a Proximity cable,
or via Bluetooth®. See chap. 2 for cable connections.
Measurements can be transmitted, and the instrument can be
controlled by predefined duplex controls, as listed in the main com-
mands section below.
Selection and conguration
BAT? Transmits battery status (BAT1=ok or BAT0=low)
ID ? Transmits instrument identication (SY276)
IN Activates Inch unit
KEY? Transmits keyboard status (KEY0 or KEY1)
KEY 0 / KEY 1 Disables/enables keypad (except Send Data)
ECO 1 / ECO 0 Enables / disables economy mode
ECO? Current economy mode
LCAL? Transmit date of last calibration (DD.MM.YYYY)
LCAL JJ.MM.[AA]AA Enter date of last calibration
MM Activates mm unit
NCAL? Transmit date of next calibration (DD.MM.YYYY)
NCAL JJ.MM.[AA]AA Enter date of next calibration
NUM ? Transmit instrument number
NUM X..X (jusqu’à 20car) Modies instrument number (10 characters)
15. List of main commands

EN
Resolution 1μm
Forward 10mm/rotation
Number of display refreshes 10/s
Measuring system Sylvac inductive system (patented)
Battery power supply 1 lithium battery 3V, type CR2032, capacity 220mAh
Average consumption 60μA (continuous)
Standby consumption 12μA
Average autonomy (auto stand-by) 10,000 hours (Bluetooth® see chapter 8)
Data output S_Connect Proximity or Bluetooth®
Data output settings 4800 baud, 7 bits, even parity, 2 stop bits, no ow control
Operating temperature +5° to 40°C (+41°F to +104°F)
IP specication (according to IEC60529) IP67 (CEI 60529)
OFF Instrument sleep mode
OUT 0 / OUT 1 Disables/disables continuous data output
PRE? Transmit preset value (±xxx.yyy[yy])
PRE ±XXX.YYYYYY Enter preset value (max. 199.999mm / 7.83'')
PRE OFF/ PRE ON Activates/deactivates Preset function
? Transmits displayed value
RST Reset instrument (user settings)
SBY Instrument stand-by (SIS)
SBY XX xx number of minutes before stand-by
SET? Transmit instrument conguration (IN or MM, STO0 or STO1, KEY0 or KEY1, BAT1 or
BAT0)
STO? Transmits display status
STO 0 / STO 1 Release/freeze display
UNI? Transmit unit of measure (IN or MM)
UNI 0 / UNI 1 Lock/release unit change function
VER? Transmit program version and date (Vx.x DD.MM.YYYY)
BT 0 / BT 1 Disables Bluetooth® module
BTRST Reset Matching
MAC ? Transmits Bluetooth® module MAC address
FMIN? Returns FMIN value
FMIN 0/ FMIN 1 Disable/enable FMIN function
FCT? Favorites function active?
FCT0…9…A…F Favorite" function assignment
RES2/3 Change resolution
16. Technical specifications
Further specifications to DIN 863-1

16
16.1. Specifications by anvil type
Measuring
range
Measurement
force Weigth Accuracy
[µm]
Repetability
[µm]
Flatness
[µm]
Parallelism
[µm]
Anvil Ø6.5mm
0-30 5N / 10N 270g 3
1
0.6
2
30-66
10N
425g 4
66-102 550g 5
3100-136 750g 7 2
125-161 850g 8
Anvil Ø2mm
0-25 5N / 10N 270g 3
1 0.6 2 25-60 10N 425g 4
60-95 550g 5 3
Anvil knifes 0.75x6.5 mm
0-25 5N / 10N 270g 3
1
1
2
25-60
10N
425g 4
60-95 550g 5
395-130 750g 62
120-155 850g 7
Anvil at / ball Ø7mm
0-30 5N / 10N 270g 3 1 1 -
Anvil ball / ball Ø7 mm
0-30 5N / 10N 270g 4 1 - -
Anvil disks Ø25 mm
0-30 5N 270g 4 (full) 1 2 5 (full)
Anvil knifes 0.5 mm / cone 60° - Ø0.5 mm
0-25 5N / 10N 270g 3 1 - -
Anvil point 30° - r 0.3 mm
0-25 5N / 10N 270g 3 1 - -

FR
1. Maintenance
Ranger l’instrument dans un endroit sec afin d’éviter la corrosion des
parties métalliques en cas de non utilisation prolongée.
Ne pas appuyer la touche mobile sur l’enclume: laisser un espace de
1-2mm lorsque l’instrument n’est pas utilisé.
Ne pas utiliser de produits agressifs (alcool, trichloréthylène ou autres
liquides agressifs) pour le nettoyage des parties plastiques.
Ne pas entreposer l’instrument dans un endroit exposé au soleil, à la
chaleur ou l’humidité.
Important: en cas de projections de liquides, essuyer les parties mé-
talliques de l’instrument afin de garantir un bon fonctionnement mé-
canique et d’éviter des problèmes de corrosion.

18
2. Description générale
Le micromètre est équipé d’un capteur SIS (Smart Inductive Sensor)
avec maintien de la position de référence même quand l’instrument
est en veille. Son principe à touche mobile non rotative permet un po-
sitionnement très rapide. Il possède les caractéristiques de fonction-
nement suivantes:
• Introduction d’une valeur de Preset.
• Changement d’unité (mm / INCH).
• Envoi de la valeur mesurée par connexion Proximity, ou Bluetooth®
(selon modèle).
• Protection contre la pénétration de poussière et contre les projec-
tions de liquide (huile, eau) selon le degré de protection IP67 (IEC
60529).
12 7
3 5 64
8
14
12
1511
10
13
9

FR
1. Touche mobile
2. Enclume
3. Plaquette isolante
4. Bouton MODE
5. Bouton Favori
6. Bouton SET
7. Tambour
8. Connecteur Proximity
9. Bouchon de pile
10. Indicateur de fin de vie batterie
11. Gel de la valeur affichée
12. Indicateur d’envoi de données
13. Verrouillage du clavier
14. Indicateur Bluetooth®
15. Indicateur mode FMIN

20
3. Les fonctionnalités de l’instrument
L’instrument possède 2 modes de travail : fonctions de base (avec
accès direct) et fonctions avancées.
En plus des fonctions de configuration, vous pouvez sélectionner
la fonction HOLD ou activer le blocage du clavier (fonction LOC).
Vous pouvez également activer la fonction FMIN (voir chap. 6).
Le bouton «favori» permet d’attribuer un accès direct à la
fonction principalement utilisée (voir chap. 10).
Le bouton «SET» permet d’attribuer une valeur de Preset, de quit-
tancer une sélection, et de gérer l’extinction de l’instrument.
Par défaut, le mode SIS permet l’extinction automatique sans
perte de l’origine (voir chap. 11).
Personnalisation des fonctions
Vous avez la possibilité d’activer ou désactiver certaines fonctions de
l’instrument par câble Power RS/USB ou Bluetooth®(voir chap. 13).
Data transmission parameters
4800Bds, 7 bits, even parity, 2 stop bits.
SET
MODE
4. Enclenchement, initialisation
Presser un bouton.
L’instrument affiche «SET» pour l’initialisation du point de référence.
Ramener la touche mobile sur l’enclume (ou sur une cale étalon).
Presser ensuite sur .
L’instrument est à présent prêt à l’emploi (contrôler la valeur du
Preset, si nécessaire corriger cette valeur et réinitialiser l’instrument).
SET