Sylvac S Dial WORK ANALOG NANO Smart User manual

INSTRUCTIONS
MODE D’EMPLOI
BEDIENUNGSANLEITUNG
MANUALE D’USO
MODO DE EMPLEO
E
S
D
F
I
DIAL GAUGE
COMPARATEUR
MESSUHR
COMPARATORE
COMPARADOR

Installing and replacing the battery
(or Power cable)
Mise en place et remplacement de la
batterie (ou câble Power)
Einbau und Austausch von Batterie
(oder Netzkabel)
Installazione e sostituzione della batteria
(o del cavo di alimentazione)
Colocación y sustitución de la batería
(o cable Power)
No. 0 No. 0 (0,4x2,5mm)
Battery / batterie / batterie / batteria / bateria: lithium 3V, type CR2032

12
12
7.5
(4x) M2
L 3.5mm
Diagram for rear xings
Schéma de xation arrière
Schema für die Befestigung hinten
Schema di ssaggio posteriore
Esquema de jación posterior

1
+2 56
mm
IN
MINMAX
PRESET
µm
TO L
OK
B
88
.. ..
11
0... 8
88
thou
08
++
H
x
mm
IN
MINMAX
PRESET
µm
TOL
thou
H
OK
B
1
+2 56
mm
IN
MINMAX
PRESET
µm
TO L
OK
B
88
.. ..
11
0... 8
88
thou
08
++
H
x
1
8
2
6
9
10
3
4 5
7
19
20
27
21
22
23 24
26
25
11
17
1613 15
18
12
14 28 29
30
4
E

5
E
Description
1. MODE button
2. SET button
3. “Favourite” button
4. button
5. button
6. Clamping shaft Ø8 or 3/8”
7. Contact point Ø2/M2.5 or 4-48-UNF
8. Lifting cap
9. Slot for Proximity cable
10. Slot for battery or Power Cable
11. Low battery
12. +/- Indicator
13. Keypad lock (chap. 4)
14. 6-digit display
15. Hold measured value (chap. 10)
16. Send data (chap. 10)
17. Measurement units mm/INCH (chap. 3)
18. Preset mode (chap. 3)
19. Analogue scale (chap. 8)
20. Lower limit exceeded
21. Upper limit exceeded
22. Tolerance indicators
23. Analogue scale lower limit (chap. 8)
24. Analogue scale upper limit (chap. 8)
25. Unit and value of analogue scale (chap. 8)
26. Tolerance mode (chap. 4)
27. MIN/MAX/DELTA mode (chap. 4)
28. Multiplier (chap. 4)
29. Bluetooth
® connection (chap. 9, depending on model)
30. Symetrical tolerances (chap. 8.1)

SET
MODE
6
E1 . Operating features of the instrument
- The instrument has two operating modes: First level functions (direct access) and Second level functions. In
addition to the conguration functions, available access to the MIN, MAX and DELTA (TIR) mode, or display of
tolerances (see chaps. 3 and 4)
- The «favourite» key gives direct access to the function used most often (see chap. 9)
- Sets a Preset value, reset the MIN/MAX mode, veries a selection, and controls switching off the instrument.
By default, SIS mode enables automatic switch-off with no loss of origin (see chap. 11).
- With the «Left and Right» buttons, the user may change the extent of the analogue scale as well as enter the
values of the nominal dimension and tolerance limits. (see chap. 6.2)
- Personalising the functions
It is possible to activate or de-activate certain functions of the instrument via RS232 (see chap. 13)
- Data transmission parameters
4800Bds, 7 bits, even parity, 2 stop bits
2. Start
Press a button. (For a Bluetooth
®connection, see chap 9.)

MODE
MODE
PRESET
-000.000mm
PrE mm
MODE
MODE
0.000mmmm SEt
MODE
mm
nor dELtA
MINMAX
mm
MAX
MAX
mm
Min
MIN
mm
ModE
SET
mm
On
TOL
mm
OFF
TOL
toL mm
AMin+ +AMAXOff
IntE
SET
MACOnbt mm mm OFF rESEt
SET
SET
PRESET PRESET
mm mm
MIN MAX
AMin-
PRESET
mm
MIN
7
E
Normal mode: Zero reset
Min (Max) mode : Preset on the measured min (max) value
3. First level functions
Each short press on gives direct access to the First level functions :
Inputting a Preset value (see chap. 7)
MIN, MAX measurement, DELTA (TIR) (see chap. 5)
2 points measurement (Dynamic preset) (see chapter 11)
Tolerance display (inputting tolerance limits, see chap. 6)
Bluetooth
® (depending on model). Enable / disable, reset
Bluetooth
®module or display its MAC address.

MODE MODE
SET
mm
-0.001
mm
+0.001
dirmm
MODE
mm
0.01
mm
0.001rES mm
MODE
MODE
MODE
MODE
mm
On
mm
OFFLocmm
MODE
SET
mm
Auto mm
MAn
OFF mm
MODE
mm
+01.0000
Mult mm
InchIN
MM mm
Unitmm
SET
SET
SET
SET
SIMPLE PAIr HId
bt.CFG +
8
E4. Second level functions
Prolonged pressure (>2s) on gives access to the Second level functions. Then, each short press on
accesses the required function :
MODE
SET
mm
-0.001
mm
+0.001
dirmm
MODE
SET
mm
0.001
mm
0.01
rES mm
MODE
SET
mm
OFF
TOL
mm
On
TOL
toL mm
MODE
SET
mm
nor
dELtA
MINMAX
mm
MAX
MAX
mm
Min
MIN
mm
ModE
MODE
Units selection (mm or Inch)
Choice of resolution 0.01 0.001 or 0.001 0.0001(depending on version)
MODE
SET
mm
-0.001
mm
+0.001
dirmm
MODE
SET
mm
0.001
mm
0.01
rES mm
MODE
SET
mm
OFF
TOL
mm
On
TOL
toL mm
MODE
SET
mm
nor
dELtA
MINMAX
mm
MAX
MAX
mm
Min
MIN
mm
ModE
MODE
Choice of measurement direction (positive or negative sense)
Multiplier introduction (see chapter 7)
Automatic switch-off mode
MAn = de-activated, Auto = active (after 10 min.)

SET
SET
SET
mm
-0.001
mm
+0.001
dirmm
MODE
mm
0.01
mm
0.001rES mm
MODE
MODE
MODE
MODE
mm
On
mm
OFFLocmm
MODE
SET
mm
Auto mm
MAn
OFF mm
MODE
mm
+01.0000
Mult mm
InchIN
MM mm
Unitmm
SET
SET
SET
SET
SIMPLE PAIr HId
bt.CFG +
9
E
........ continuation
5. Work in MINIMUM, MAXIMUM and DELTA (TIR) modes:
In this operating mode, the digital display stores the MIN, MAX or DELTA value. On the other hand, the analogue scale
always indicates the current measured value.
- A short press on resets the MIN/MAX stored value (CLEAr)
- A long press (>2s) on assigns the Preset value to the position of current measurement.
Choice of resolution 0.01 0.001 or 0.001 0.0001(depending on version)
Bluetooth
® prole selection (depending on model, see chap. 6 for details).
The + sign indicates the currently active prole.
Keypad lock, Only the DATA and CLR functions of the favorite key
remains actives. (to unlock the keypad, press SET for 5 sec.

10
E
..................... Input the nominal value
(see chap. 7)
..................... Input the lower tolerance limit
(see chap. 7)
..................... Input the upper tolerance limit
(see chap. 7)
6. Inputting (or modifying) tolerance limits
The tolerance limits are dened by introducing lower and upper intervals, compared to the nominal rating.
Two methods are available:
6.1 Using the TOL mode