Sylvac Ps16 v2 User manual

MEASURING BENCH PS16 V2

BANC DE MESURE PS16 V2

MESSBANK PS16 V2

INSTRUCTIONS

MODE D’EMPLOI

BEDIENUNGSANLEITUNG

1 3 2 16 12

13 14

1598710

Description

1. MODE button

2. SET button

3. “Favourite” button

4. Mini-USB

5. Compartment for battery CR2477 or CR2032.

6. Adapter CR2477/CR2032

7. Adjustable release lever

8. Optional stop

9. Travel stop

10. Force adjustment knob

11. Anvils locking screw Ø1.5mm

12. Moving measurement spindle for Sylvac Ø1.5 probe and Cary compatible probe

13. Fixed measurement spindle for Sylvac Ø1.5 probe and Cary compatible probe

14. Moveable tailstock

15. Tailstock position locking screw

16. Measurement unit

17. Proximity cable housing

Handling

Unblocking the transport mode axes

Place the 2 optional stops (on the front and rear of the unit) in their middle position.

First use

For the rst use, after a complete stop (off) or battery change, the instrument will

request a new reference measurement (--rEF--).

Move the measurement axis to the end of its run, (fully entered)

1. General usage remarks

• The original anvils assembled on both measurement axes are lapped in position

to guarantee an optimum measurement. Any disassembly of these anvils can

lead to a reduction in the accuracy of the instrument.

• The tailstock was positioned to have 0.5mm prestress in the probe zero position.

• Activating the lever opens the anvils. Releasing the release lever too sharply

can have a harmful inuence on the probes and the measurement accuracy.

• It is advisable to check the reference (origin) during use.

• Monitor the cleanliness of the moving spindle. If necessary clean with light ben-

zene. Using a cloth that could leave residual particles is not recommended.

• Certain components, notably the headstock clamp screws are sealed after

assembly and consequently must not be removed. Any work on these compo-

nents by a third party can lead to loss of the guarantee.

2.1 Adjustable release lever

The movable measuring spindle is retracted by means of the adjustable lever (7). The

position of the lever can be adjusted to suit the location of the workpiece. In order to

change the position, pull the lever out axially and move it to the desired position.

2. Use

2.2 Optional stops

The PS16 V2 is equipped with 2 optional stops (at the front and back of the

instrument). Used in combination, they allow the travel to be restricted in 2

directions (opening/closing) so that the position and the measuring travel can

be adjusted to suit the workpiece.

This prevents the anvils from coming back into contact (0) and having to repeat the

full travel with each measurement. The stop is engaged by pushing the radial button

(8).

The stop positions are adjusted by positioning the release lever (see chap. 2.1). If 2

stops are being used, the release lever has a set position that cannot be modied.

2.3. Measuring force

The measuring force can be adjusted by moving the adjustment knob (10) as follows:

unscrew the knob (~1/2 a turn), position it at the required force and re tighten it.

Optimise the measuring force setting for workpiece weight and deformation. Do not

adjust the measuring force during a measurement process.

Force for external measurement PS16 V2 25mm

Force for internal measurement PS16 V2 50mm

Force for internal measurement PS16 V2 25mm

Force for external measurement PS16 V2 50mm

14 7

3.1. Description

1. Active reference

2. Measuring mode with 3-point function

3. Tolerance indicator

4. Multiplication factor

5. Sending data

6. Keypad lock

7. Hold measured value

8. 6-digit display

9. Tolerance mode

10. Preset Mode

11. Mode Min/Max/Delta

12. MODE menu indicator

13. Low battery

14. Indicator + / -

15. Measurement unit mm/INCH

16. Bluetooth® connection

3. Measurement unit

216

SET

MODE

3.1.1 Operating features of the instrument

- The instrument has two operating modes: basic functions (direct access)

and advanced functions. In addition to the conguration functions, 2

working reference functions can be accessed, in MIN, MAX and DELTA

(TIR) mode, plus tolerance display or input of multiplication factor other

than 1:1 (see chaps. 3.3 and 3.4)

- The «favourite» key gives direct access to the function used most often

(see chap. 3.6)

- Sets a Preset value, reset the MIN/MAX mode, veries a selection, and

controls switching off the instrument. By default, SIS mode enables

automatic switch-off with no loss of origin (see chap. 6)

3.1.2. Personalising the functions

It is possible to activate or deactivate certain functions of the instrument.

(requires a connection, see chap. 6.2)

3.1.3. Data transmission parameters

4800Bds, 7 bits, even parity, 2 stop bits

3.2. Start, re-initialisation

Press a button.

When the instrument is used for the rst time after the battery has been

changed or after it has been completely switched off (OFF), the instrument

needs to be reinitialised (--rEF-- ). Simply insert the measuring spindle to

the end of its travel.

For a Bluetooth®connection (see chap. 4).

MODE

3.3. Basic functions

Each short press on gives direct access to the basic functions :

MODE

SET

MODE

SET

MODE

bt rESEt MAC

SET

MODE

rEf.. Choice of reference (REF1 or REF2)

MODE

SET

Note :

It is possible to assign a different preset value to each of the 2 References. Similarly,

different tolerance limits can be assigned to References 1 and 2.

MODE

SET

MODE

SET

MODE

SET

MODE

SET

OFF On

MODE

3.4. Advanced functions

Prolonged pressure (>2s) on gives access to the advanced functions.

Then, each short press on accesses the required function :

ModE Minimum, Maximum and Delta (TIR) measurement

toL Tolerance display

(inputting tolerance limits, see chap. 3.5)

bt Bluetooth®ON/OFF or MAC address display

PrE...... Inputting a Preset value

next digit 0...9 save the PRESET

MODE

SET

MODE

bt rESEt MAC

SET

MODE

SET

MODE

SET

bt,CFG HId

PAIr

SIMPLE

SET

MODE

3.5. Inputting tolerance limits

To input or modify the tolerance limits, tol → On mode should be selected, followed

by a short press on

MODE

3.4. Advanced functions (continuation)

Unit . Units selection (mm or Inch)

rES Choice of resolution (depending on version)

dir Choice of measurement direction (positive or negative sense)

MuLt Inputting a multiplication factor other than 1.0000

Next digit 0...9 save MULT

OFF Automatic switch-off mode

MAn = de-activated, Auto = active

bt.CFG Bluetooth® prole selection (depending on model).

(see chap. 4 for details)

The + sign indicates the currently active prole.

Loc Keypad lock. Only the favourite key remains active

(to unlock the keypad, press for 5 sec)

3Pts Diameter measurements at 3 points (for 3 points version)

SET

MODE

SET

MODE

SET

3Pts

On Off

OnOFF

rESEt MAC

SET

MODE

SET

bt,CFG HId

PAIr

SIMPLE

SET

MODE

SET

Input the lower tolerance limit

Input the upper tolerance limit

next digit 0...9 save TOL

Note:

3.6. Favourite key

The «favourite» key gives direct access to a predened function, and can be

congured according to the needs of the user. In order to assign a function to

the «favourite» key.

Give a prolonged press on , and then select the required function :

13 no.F

Data transmission

(default)

Hold display

Re-initialise

Min-Max-Delta

Zero reset

REF1 - REF2

Recall Preset

Nor–Min–Max-Delta

Tol ON–Tol OFF

For measuring internal dimensions, the red and yellow indicators can be switched

over by reversing the order in which the tolerance limits are input (lower limit >

upper limit).

It is possible to input different tolerances on REF1 and REF2.

It is also possible to display the tolerance limits when the instrument is operating

in MIN, MAX or DELTA (TIR) mode.

If no tolerance limits have been dened by the user, the instrument will display the

tolerance limits have indicators , but will not turn on the indicator lights

(red - green - yellow)

13 no.F

The connection procedure has been designed to be simple and is signalled by

the following three states:

Symbol off.............. disconnected mode

Symbol blinking...... advertising mode

Symbol on.............. connected mode

Bluetooth®ON or OFF

(depending on model)

mm – IN

0.001 – 0.0001

Measurement sense

positive - negative

MODE

SET

4. Bluetooth® conguration

Validation of selection: By a prolonged press on or a short press on or .

Note:

A function can also be assigned via RS232 using the command

<FCT + Function No.> (FCT 0..9 A..F)

example: Toggle unit = <FCT9>, reverse measurement direction = <FCTB>.

3.6. Favourite key (continuation)

13 no.F

1:1 - N:1 factor

No function

13 no.F

MODE

SET

MODE

bt rESEt MAC

SET

MODE

The following options can be selected to control the Bluetooth®module.

On Enable Bluetooth®module (start advertising mode).

OFF Disable Bluetooth®module (terminate active connection).

rESEt Clear pairing information.

MAC Display the MAC (Media Access Control) address.

Three Bluetooth® proles are available.

SIMPLE Prole without pairing (default).

PAIr Paired and secured prole.

HId Virtual keyboard mode (compatible with recent equipment without driver installation).

Note:

- Bluetooth® pairing information is cleared when the prole is changed.

Only with paired prole :

Pairing with master is automatically done at rst connection.

To connect the instrument to a new master (new pairing), pairing information on the

instrument must be cleared using the bt / rESEt menu.

Other specications on the manufacturer’s website.

5. Adjusting the 3 points measurement system (for 3 point model)

To adjust the 3 points measurement system, select the 3 Pts ON menu and then

briey press .

MODE

SET

Enter the diameter of the pins

next digit 0...9 save the value.

Enter the diameter of master gauge 1

3 pts On Off

MODE

8.000

4.002

00.5000

04.0020

08.0000

SET

Connection:

1 Activate Bluetooth® Smart compatible software and hardware (Master : PC, Display Unit)

2 Start the instrument. By default the Bluetooth®module is active and the instrument

is available for connection (advertising mode)

3 If no connection is established during the advertisement period reactivate the

Bluetooth®module using the bt / On menu.

4 Instrument is ready to communicate (connected mode)

Frequency Band 2.4GHz (2.402 - 2.480GHz)

Modulation GFSK (Gaussian Frequency Shift Keying)

Max Output Power Class 3: 1mW (0dBm)

Range Open space: up to 15m

Industrial environment: 1-5m

Battery life

Continuous : up to 2 months - Always connected with 4 values /sec.

Saver : up to 5 months - The instrument sends value only when the

position has changed.

Blind/Push : up to 7 months - Value is sent from the instrument (button)

or requested from the computer.

4.1. Bluetooth® specifications

SET

>2s

SET

12.3456

>4s

SET

12.3456 Off

6. Switching off

The dial gauge goes automatically into stand-by if not used for 10 minutes, unless

automatic switch-off mode has been turned off (see Chap. 3.4, advanced functions)

Stand-by mode can be forced by a prolonged press (> 2 sec) on

In stand-by mode, the value of the origin is retained by the sensor (SIS mode),

and the instrument automatically restarts with any movement of the measurement

probe, RS command, Bluetooth®request or press a button.

The instrument can be switched off completely for a long period of non-use, but

this will necessitate a zero reset on restart (the origin will be lost) :

Prolonged press (>4 sec) on :

5. Adjusting the 3 points measurement system (continued)

Enter the diameter of master gauge 2

Measure gauge 1 1)

Conrm the measurement of gauge 1

Measure gauge 1)

Conrm the measurement of gauge 2

The PS16 is ready to measure. The rEF 1 and rEF 2 reference presets (PrE function)

are set to the value of the two gauges.

1) the display will return to measurement mode as soon as the measurement probe is

moved, to allow for ideal gauge positioning.

3 pts On Off

MODE MODE

MODE

8.000

4.002

00.5000

04.0020

08.0000

SET

3 pts On Off

MODE MODE

MODE

8.000

4.002

00.5000

04.0020

08.0000

SET

3 pts On Off

MODE MODE

MODE

8.000

4.002

00.5000

04.0020

08.0000

SET

6.1. Re-initialising the instrument

The initial instrument settings can be restored at any time by a prolonged press (>4

sec) simultaneously on and until the message rESEt.The instrument

now needs to be reinitialised.

SET

MODE

6.2. Personalising the instrument

Access to the functions of your instrument can be personalised, for more information

see manufacturer’s website (requires you to connect your instrument via an USB

cable, Proximity or Bluetooth®).

Possibilities:

- Enable or disable the required functions

- Modify access to the advanced functions (direct access)

6.3. Connecting the instrument

The instrument can be connected to a peripheral device via a USB, or Proximity

cable or via Bluetooth®. Measurement values can be transmitted and the instrument

can be controlled with the help of predened remote commands (for a list of the main

commands, see chap. 7).

Note:

In Tolerance mode, the tolerance limit lights remain lit only for a few seconds while the

measurement stabilises. However, they will remain permanently lit if the instrument is

connected and powered by the USB connector.

Selection and conguration Interrogation

CHA+ / CHA- Change measurement direction CHA? Measurement sense?

FCT0 ...9...A...F Assign «favourite» function FCT? «favourite» function active?

MM / IN Change measurement unit UNI? Measurement unit active?

KEY0 / KEY1 Lock / unlock keypad KEY? Keypad locked?

MUL [+/-]xxx.xxxx Modify multiplication factor MUL? Multiplication factor?

PRE [+/-]xxx.xxx Modify preset value PRE? Preset value?

REF1 / REF2 Change active reference REF? Reference active?

STO1 / STO0 Activate / de-activate HOLD STO? Status of HOLD function?

TOL ON / TOL OFF Activate / de-activate tolerances TOL? Current tolerance limit values?

ECO1 / ECO 0 Activate / de-activate economic mode ECO? Current economic mode

LCAL dd.mm.yy Modify last calibration date LCAL? Date of last calibration?

NCAL dd.mm.yy Modify next calibration date NCAL? Date of next calibration?

NUM x...x (up to 20chars) Modify the instrument number NUM? Instrument number?

TOL +/-xxx.xxx +/-yyy.yyy Inputting tolerance limits ? Current value (mode Tol, value followed by <=>)

MIN /MAX /DEL /NOR Selecting MIN, MAX, Delta, Normal mode MOD? Active mode (MIN, MAX, Delta or Normal)?

CLE Re-initialisation of MIN, MAX or Delta SET? Main instrument parameters?

UNI1 / UNI0 Activate / de-activate change of units ID? Instrument identication code?

OUT1 /OUT0 Activate / de-activate contin. data transmission Maintenance functions

PRE ON / PRE OFF Activate / de-activate Preset function BAT? Battery status (BAT1 = OK, BAT0 = low battery)

PRE Recall Preset OFF Switch-off (wake up using a button or RS)

SET Zero reset RST Re-initialisation of the instrument

RES1 / RES2 Change of resolution SBY Put instrument in stand-by (SIS)

SBY xx xx number of minutes before stand-by

BT0/BT1 Activate / de-activate Bluetooth®module

BTRST Reset pairing information

7. List of the main commands