Sylvac S Dial WORK Smart User manual

INSTRUCTIONS
MODE D’EMPLOI
BEDIENUNGSANLEITUNG
MANUALE D’USO
INSTRUCCIONES DE USO
E
S
D
F
I
DIAL GAUGE
COMPARATEUR
MESSUHR
COMPARATORE
COMPARADOR

Installing and replacing the battery
(or Power cable)
Mise en place et remplacement de la
batterie (ou câble Power)
Einbau und Austausch von Batterie
(oder Netzkabel)
Installazione e sostituzione della batteria
(o del cavo di alimentazione)
Colocación y sustitución de la batería
(o cable Power)
No. 0 No. 0 (0,4x2,5mm)
Battery / batterie / Batterie / batteria / bateria: lithium 3V, type CR2032

12
12
7.5
(4x) M2
L 3.5mm
Diagram for rear fixings
Schéma de fixation arrière
Schema für die Befestigung hinten
Schema di fissaggio posteriore
Esquema de fijación posterior

9
14
18
21
10
17
13
12
1
5
2
4
7
8
16
19
3
6
23 20
15
11
22
4
E

5
E
Description
1. MODE button
2. SET button
3. “Favourite” button
4. Clamping shaft Ø8 or 3/8”
5. Lifting cap
6. Contact point Ø2/M2.5 or 4-48-UNF
7. Slot for Proximity cable
8. Slot for battery or Power cable
9. Measurement units (mm/INCH)
10. +/- Indicator
11. Low battery
12. Mode menu display
13. MIN/MAX/DELTA mode
14. Preset mode
15. Tolerance mode
16. 7- digit display
17. Hold measured value
18. Keypad lock
19. Send data
20. Bluetooth
®active ( depending on model )
21. Multiplication factor
22. Tolerance indicators
23. Active reference

SET
MODE
6
E1. Operating features of the instrument
- The instrument has two operating modes: basic functions (direct access) and advanced functions. In addition
to the configuration functions, 2 working reference functions can be accessed, in MIN, MAX and DELTA (TIR)
mode, plus tolerance dispay or input of multiplication factor other than 1:1 (see chaps. 3 and 4).
- The «favourite» key gives direct access to the function used most often (see chap. 7).
- Sets a Preset value, resets the MIN/MAX mode, verifies a selection, and controls switching off the instrument.
By default, SIS mode enables automatic switch-off with no loss of origin (see chap. 8).
- Personalising the functions
It is possible to activate or de-activate certain functions of the instrument via RS232 (see chap. 10).
- Data transmission parameters
4800Bds, 7 bits, even parity, 2 stop bits.
2. Start Press a button.
For a Bluetooth
®connection (see chap. 6).

MODE
MODE
MODE
SET
MODE
MODE
SET
7
E
3. Basic functions
Each short press on gives direct access to the basic functions :
– Choice of reference
(REF1 or REF2)
– Inputting a Preset value
next digit 0...9
save PRESET
Note:
- It is possible to assign a different preset value to each of the 2 References. Similarly,
different tolerance limits can be assigned to References 1 and 2.

MODE
SET
MODE
bt rESEt MAC
SET
SET
MODE
8
E........ continuation
– MIN, MAX measurement
DELTA (TIR)
– Tolerance display
(inputting tolerance limits,
see chap. 5)
– Bluetooth®(depending on
model). Enable / disable,
reset Bluetooth®module
or display its MAC address.

MODE MODE
MODE
MODE
SET
SET
MODE
SET
MODE
SET
MODE
SET
OFF On
MODE
MODE
SET
MODE
SET
bt,CFG HId
PAIr
SIMPLE
SET
MODE
MODE
9
E
4. Advanced functions
Prolonged pressure (>2s) on gives access to the advanced functions.Then, each short press on accesses
the required function:
– Unit selection (mm or inch)
– Choice of resolution 0.01 / 0.001 or 0.001 / 0.0001
(depending on version)
– Choice of measurement direction
(positive or negative direction)
– Multiplication factor, enable or disable multiplication factor
(value can be modified if On is confirmed by button)
– Input of multiplication factor, next digit 0....9
save MULT

SET
SET
MODE
SET
bt,CFG HId
PAIr
SIMPLE
SET
MODE
MODE
10
E........ continuation
Keypad lock
Only the favourite key remains
active.(to unlock the keypad, press
for 5 sec).
Automatic switch-off mode
MAn = disabled, Auto = active
(after 10 min. by default).
Bluetooth®profile selection (depending
on model).
(see chap. 6 for details)
The +sign indicates the currently active
profile.

MODE
MODE
SET
MODE
MODE
SET
MODE
11
E
— Input the lower tolerance limit
— Input the upper tolerance limit
next digit 0...9 save TOL
5. Inputting tolerance limits
To input or modify the tolerance limits, toL On mode should be selected, followed by a short press on :
Note:
- For measuring internal dimensions, the red and yellow indicators can be switched over by reversing the order in which
the tolerance limits are input (lower limit > upper limit).
- It is possible to input different tolerances on REF1 and REF2.

12
E
6. Bluetooth
®configuration (depending on model)
The connection procedure has been designed to be simple and is signalled by the following three states:
° Symbol off ............. disconnected mode
° Symbol blinking...... advertising mode
° Symbol on.............. connected mode
- It is also possible to display the tolerance limits when the instrument is operating in MIN, MAX or DELTA (TIR) mode.
- If no tolerance limits have been defined by the user, the instrument will only display the tolerance limit indicators
but will not turn on the indicator lights (red - green - yellow).
OK
The following options can be selected to control the Bluetooth®module.
On Enable Bluetooth®module (start advertising mode).
OFF Disable Bluetooth®module (terminate active connection).
rESEt Clear pairing information.
MAC Display the MAC (Media Access Control) address.

13
E
Connection:
1° Activate Bluetooth
®compatible software and hardware (Master : PC, Display Unit).
2° Start the instrument. By default the Bluetooth
®
module is active and the instrument is available for connection (advertising
mode).
3° If no connnection is established during the advertisement period reactivate the Bluetooth
®module using the bt / On menu.
4° Instrument is ready to communicate (connected mode.)
Only with paired profile:
Pairing with master is automatically done at first connection.
To connect the instrument to a new master (new pairing), pairing information on the instrument must be cleared using the bt /
rESEt menu.
Three Bluetooth®profiles are available.
SIMPLE Profile without pairing (default).
PAIr Paired and secured profile.
HId Virtual keyboard mode (compatible with recent equipement without driver installation).
Note:
- Bluetooth®pairing information is cleared when the profile is changed.

14
E6.1
Bluetooth
®specifications
Frequency Band 2.4GHz (2.402 - 2.480GHz)
Modulation GFSK (Gaussian Frequency Shift Keying)
Max Output Power Class 3: 1mW (0dBm)
Range Open space: up to 15m
Industrial environment: 1-5m
Battery life
Continuous : up to 2 months - Always connected with 4 values /sec.
Saver : up to 5 months - The instrument sends value only when the position has changed.
Blind/Push : up to 7 months - Value is sent from the instrument (button) or requested from the
computer.
Other specifications on the manufacturer’s website.

MODE
SET
15
E
7. Favourite key
The «favourite» key gives direct access to a predefined function, and can be configured according to the needs of the user.
In order to assign a function to the «favourite» key, give a prolonged press on , and then select the required function:
Validation of selection: By a prolonged press on or a short press on or .
Note:
- A function can also be assigned via RS232 using the command <FCT + Function No.> (FCT 0..9 A..F)
example:Toggle unit = <FCT9>, reverse measurement direction =<FCTB>.
12
bt
13 no.F
Data
transmission
(default)
Hold display
Re-initialise
Min-Max-Delta
Zero reset
REF1 - REF2
Recall Preset
Nor-Min-Max-
Delta
Tol ON -Tol OFF
1:1 - N:
1 factor
No function
Bluetooth®ON-OFF
(depending on model)
mm – IN
0.01 ↔ 0.001 or
0.001 ↔ 0.0001
Measurement direction,
positive - negative

SET
SET
SET
MODE
>2s
SET
>4s
SET
16
E8. Switching off
The dial gauge goes automatically into stand-by if not used for 10 minutes, unless automatic switch-off mode has been
turned off (see Chap. 4, advanced functions).
Stand-by mode can be forced by a prolonged press (> 2 sec) on :
In stand-by mode, the value of the origin is retained by the sensor (SIS mode), and the instrument automatically restarts
with any movement of the measurement probe, RS command, Bluetooth®request or press on button.
The instrument can be switched off completely for a long period of non-use, but this will necessitate a zero reset on restart
(the origin will be lost):
- Prolonged press (>4 sec) on :
9. Re-initialising the instrument
The initial instrument settings can be restored at any time by a prolonged press (>4 sec) simultaneously on and
until the message rESEt is displayed.

17
E
10. Personalising the instrument
Access to the functions of your instrument can be personalised, for more information see manufacturer’s website (re-
quires you to connect your instrument via Proximity or Power RS / USB cable, or Bluetooth
®).
Possibilities :
- Enable or disable the required functions.
- Modify access to the advanced functions (direct access).
11. Connecting the instrument
The instrument can be connected to a peripheral via a Proximity (RS or USB), Power (RS or USB) cable or Bluetooth
®.
See page 2 for connecting the Power cable.
Measured values can be transmitted and the instrument driven using predefined commands (see chap. 12 for a list of
the main commands).
Note:
- In Tolerance mode, the tolerance limit lights remain lit only for a few seconds while the measurement stabilises.
On the other hand, they will remain lit continuously if the instrument is connected to, and powered by, the Power RS
(USB) cable.

18
E12. List of the main commands
Selection and configuration Interrogation
CHA+ / CHA- Change measurement direction CHA? Measurement direction?
FCT0 ...9...A...F Assign «favourite» function FCT? «favourite» function active?
MM / IN Change measurement unit UNI? Measurement unit active?
KEY0 / KEY1 Lock / unlock keypad KEY? Keypad locked?
MUL [+/-]xxx.xxxx Modify multiplication factor MUL? Multiplication factor?
PRE [+/-]xxx.xxx Modify preset value PRE? Preset value?
REF1 / REF2 Change active reference REF? Reference active?
STO1 / STO0 Activate / de-activate HOLD STO? Status of HOLD function?
TOL1 / TOL0 Activate / de-activate tolerances TOL? Current tolerance limit values?
ECO1 / ECO 0 Activate / de-activate economic mode ECO? Current economic mode
LCAL dd.mm.yy Modify last calibration date LCAL? Date of last calibration?
NCAL dd.mm.yy Modify next calibration date NCAL? Date of next calibration?
NUM x...x (up to 20chars) Modify the instrument number NUM? Instrument number?
TOL +/-xxx.xxx +/-yyy.yyy Inputting tolerance limits ? Current value (mode Tol, value followed by <=>)
MIN /MAX /DEL /NOR Selecting MIN, MAX, Delta, Normal mode MOD? Active mode (MIN, MAX, Delta or Normal)?
CLE Re-initialisation of MIN, MAX or Delta SET? Main instrument parameters?
UNI1 / UNI0 Activate / de-activate change of units ID? Instrument identification code?
OUT1 /OUT0 Activate / de-activate contin. data transmission
Maintenance functions
PRE ON / PRE OFF Activate / de-activate Preset function BAT? Battery status (BAT1 = OK, BAT0 = low battery)
PRE Recall Preset OFF Switch-off (wake up using a button or RS)
SET Zero reset RST Re-initialisation of the instrument
RES1 / RES2 / RES3 Change of resolution SBY Put instrument in stand-by (SIS)
VER? Version No. and date of firmware
SBY xx xx number of minutes before stand-by
BT0/BT1 Activate / de-activate Bluetooth®module MAC? Bluetooth®MAC address ?
BTRST Clear pairing information

13. Specifications
Measurement range: 12.5mm 25mm 50mm 100mm 150mm
Max error (10µm resolution): 10µm 10µm 20µm 20µm 20µm (±1 digit)
Max error (1µm resolution): 3µm 4µm 5µm 6µm 10µm
Max error (0.1µm resolution): 1.8µm 2.2µm --- --- ---
Repeatability: 2µm 0.5µm (model 0.0001mm scale)
Weight: 119g 123g 161g 208g 265g
Measurement force (standard): 0.65-0.9N 0.65-1.15N 1.25-2.7N 1.6-3.5N 2.2-5.7N
Max. speed of travel: 1.7m/s
No. of measurements / second: up to 10 meas/s MIN/MAX mode: up to 20 meas/s
Measurement unit: metric/english (Inch)
Maximum Preset (10µm resolution): ±9999.99 mm / ±399.9995 IN
Maximum Preset (1µm resolution): ±999.999 mm / ±39.99995 IN
Maximum Preset (0.1µm resolution): ±99.9999 mm / ±3.999995 IN
Measurement system: Sylvac inductive system (patented)
Power: 1 x 3V lithium battery, type CR2032, 220mAh
Average battery life: 8’000 hours (with
Bluetooth® enabled, see chapter 6.1)
Data output: RS232 compatible / Bluetooth®4.0 (see chapter 6)
Working temperature (storage): +5 to +40°C (-10 to +60°C)
Electromagnetic compatibility: as per EN 61326-1
IP rating (in accordance with IEC60529): IP 54 / IP 67 (depending on model)
Fixing and space envelope: Ø8h6 (3/8’’), interchangable M2.5 (4-48-UNF) probe (as per DIN 878)
19
E

9
14
18
21
10
17
13
12
1
5
2
4
7
8
16
19
3
6
23 20
15
11
22
20
F