Symmons Dia S-3504-H321-V-CYL-B-TRM Manual

S-3504-H321-V-CYL-B-TRM
Dia®Tub/Hand Shower Trim
Operation & Maintenance Manual
Model Numbers Specifications
S-3504-H321-V-CYL-B-TRM Tub/Hand Shower Trim Tub/hand shower trim with lever handle and secondary
integral diverter handle includes wall connection, 30"
slide bar, non-diverter tub spout, exible metal hose and
1 mode hand shower with dual checks, and 2.5 gpm
(9.5 L/min) ow restrictor. Components made from metal
and plastic materials plated in standard polished chrome
nish.
Modifications Compliance
-1.5 1.5 gpm (5.7 L/min) flow restrictor
-2.0 2.0 gpm (7.6 L/min) flow restrictor
Delete Chrome plastic escutcheon on valve with
Suffix B color graphics/indicators in place of
standard brass escutcheon
-STN Satin nickel finish
-ASME A112.18.1/CSA B125.1
Warranty
Limited Lifetime - to the original end purchaser in
consumer installations.
5 Years - for commercial installations.
Refer to www.symmons.com/warranty for complete
warranty information.
Note: Append appropriate -sufx to model number.
CG
CG WARNING: This product can expose you to
chemicals including lead, which is known to the
state of California to cause cancer, birth defects, or
other reproductive harm. For more information, go
to www.P65Warnings.ca.gov.

2
HH
AA
D
D
M
M
I
I
G
G
B
B
E
E
F
F
J
J
N
N
L
L
K
K
FloorFloor
C
C
DimensionsDimensions
Notes:
1) All dimensions measured from nominal rough-in (see J as reference).
2) Dimensions are subject to change without notice.
Measurements
A 2 1/8", 54 mm
B
1/2" NPT thread must
be recessed 1/4" from
nished wall
C 6", 152 mm right or left
DØ 7 1/2", 191 mm (brass)
Ø 7 3/4", 197 mm (plastic)
E 3 1/2", 89 mm
F 3", 76 mm
G 12", 305 mm
H 3 1/8", 79 mm
I 32", 813 mm
J(Rough in)
2 3/8" ± 1/2", 60 mm ± 13 mm
K 1/2" NPT
L 5 1/4", 133 mm
M Ø 2 1/2", 64 mm
N 7", 178 mm

3
E
A
B
D
L
C
F
M
G
H
K
J
I
Parts Breakdown
Replacement Parts
Item Description Part Number
A Hose RTS-045
C Handle Assembly T-242A
D Dome Cover T-19
E
F
G
Escutcheon
Mounting Screws
Mounting Plate
RTS-011 (Brass)
RTS-012 (Plastic)
HHand Shower
Wand EF-100
I
J
K
Slide Bar
Bracket Caps
Mounting Screws
SC-115
LSecondary Diverter
Handle
RTS-013 (Brass)
RTS-014 (Plastic)
M Tub Spout 067
Note:
1) Append -STN to part number for Satin Nickel
nish.
2) Append -1.5 or -2.0 to hand shower for low
ow.
Required for Installation
Adjustable wrench
Phillips head screwdriver
Allen wrench, 3/16"
Teon Tape
Power Drill
Notes:
1) Apply a bead of silicone around the perimeter of all shower trim
installed ush to the nished wall. Leave opening on bottom of
escutcheons for weep hole.
2) Apply plumber tape to all threaded connections.
EF-109*
*Order in-line vacuum breaker (EF-109) for hand
shower systems without dual checks.

4
Note:
For valve body installation, please
see valve body installation guide.
1) Install plastic mounting plate (G)
to shower valve (S-4002-BODY).
Secure with two screws (F).
2) Attach secondary integral diverter
(L) to shower escutcheon (E).
3) Attach shower escutcheon (E) to
plastic mounting plate (G).
Note: Tabs should snap into place.
4) Install dome cover (D) to valve by
turning clockwise.
5) Install shower handle (C) to valve.
Secure handle by tightening Allen
screw.
Note: Handle should be facing the
6 o'clock position.
6) Install tub spout (M) to stub out
pipe. Turn clockwise to secure.
7a) Dry Wall Option: R emove
upper and lower caps (J) from
30" slide bar brackets. Place
30" slide bar (I) into desired
position. Using brackets as a
guide, carefully drill 5/16" holes
into wall. Remove 30" slide bar
and install anchors.
Notes: Make sure that 30" slide
bar holes and bracket holes are
aligned before drilling. Before
drilling bottom hole, make
sure 30" slide bar is plumb.
1
2
F
G
E
G
1
2
D
1
2
2
C
4
4
1
1
2
2
3
I
J
J
1
2
M
L
E
Installation

5
7b) Stud Option: R emove upper
and lower caps (J) from 30"
slide bar brackets. Place
30" slide bar (I) into desired
position. Using brackets as a
guide, carefully drill 1/8" pilot
holes into stud.
Notes: Make sure that 30" slide bar
holes and bracket holes are aligned
before drilling. Before drilling bottom
hole, make sure 30" slide bar is
plumb.
8) With 30" slide bar (I) in position,
secure to wall using screws (K).
Replace upper and lower caps (J)
onto 30" slide bar brackets.
9) Install wall elbow (B) to stub out
pipe. Tighten Allen screw (3 mm)
to secure.
10) Attach large end of hand
shower hose (A) to hand
shower head (H). Attach small
end of hand shower hose (A) to
wall elbow (B). Turn clockwise
to tighten.
1
1
2
2
3
I
J
J
2
2
1
K
II
J
J
Installation
1
2
B
3
1
4
2
A
H
A
B

1) Turn shower handle counterclockwise approximately
1/4 turn to put valve in cold position.
2) Turn shower handle counterclockwise approximately
1/2 turn to put valve in warm position.
3) Turn shower handle counterclockwise
approximately 3/4 turn to put valve in hot position.
1) Turn diverter lever left for tub spout operation.
2) Turn diverter lever right for hand shower operation.
Symmons Industries, Inc. ■31 Brooks Drive ■Braintree, MA 02184 ■Phone: [phone] ■ Fax: [phone]
Copyright © 2018 Symmons Industries, Inc. ■symmons.com ■[email protected] ■ZV-3027 REV B ■ 081318
Care and Cleaning
1) Clean nished trim area with a soft cloth using mild soap and water or a non-abrasive cleaner and then quickly rinse
with water.
Troubleshooting Chart
Problem Cause Solution
Finish is spotting. Elements in water supply may cause
water staining on nish.
Clean nished trim area with a soft
cloth using mild soap and water or a
non-abrasive cleaner and then
quickly rinse with water.
Operation
Temperature Diverter Control