Symmons Dia SK3510PD Manual

Model Numbers Feature Highlights
☐SK3510PD Single Handle Pull-Down Kitchen
Faucet, Polished Chrome
• Pull-down spray wand with 2 mode spray selector,
• 3/8 inch supply hose compression connections
• 1.5 gpm (5.7 L/min) standard flow rate
• Metal construction plated in standard polished chrome
finish
Compliance
- ASME A112.18.1/CSA B125.1
- NSF/ANSI/CAN 61: Q<1, NSF/ANSI 372
Dimensions
Limited Lifetime - to the original end
purchaser in consumer/residential
installations.
10 Years - for commercial/industrial
installations. Refer to
www.symmons.com/warranty for
complete warranty information.
Warranty
SK3510PD
Single Handle Pull-Down Kitchen Faucet
Operation & Maintenance Manual
Symmons Industries, Inc. ■31 Brooks Drive ■Braintree, MA 02184 ■Phone: [phone] ■ Fax: [phone]
Copyright © 2023 Symmons Industries, Inc. ■symmons.com ■[e-mail] ■ZV-3749 REV 0 ■ 060623
Dia®
Hole Size
Min. Ø 1-3/8" (35mm)
Max. Ø 1-1/2" (38mm)
Deck Thickness Reference
Max. 2-1/2" (64mm)
For Optional Deck Plate
(2x) Hole Size
Min. Ø 1" (25mm)
Max. Ø 1-1/4" (32mm) Note: Dimensions subject to change without notice.
WARNING: This product can expose you to chemicals
including lead, which is known to the state of California to
cause cancer, birth defects, or other reproductive harm.
For more information, go to www.P65Warnings.ca.gov.

2
*Note: Append -STN to part number for Satin Nickel
nish.
Notes:
1) Apply a bead of silicone around the perimeter of trim
installed ush to sink.
2) DO NOT use plumber putty or plumber tape on ttings
with face seal washers or o-ring seals.
3) DO NOT OVERTIGHTEN ttings with face seal washers
or o-ring seals.
Replacement Parts
Item Description Part Number
1 Wand RK-054*
2 Cartridge KN-4
3
4
5
6
Lever
O-ring
Set Screw
Handle Hub
RK-055*
7
8
9
10
Deck Plate
Shanks
Gasket
Mounting Nuts
RK-057*
11
12
13
14
Plastic Washer
Metal Washer
Mounting Nut
Mounting Screws
RK-028
15
1.0 gpm Adapter
1.5 gpm Adapter
2.2 gpm Adapter
RK-060-1.0
RK-060-1.5
RK-060-2.2
Parts Breakdown
Tools Required
Adjustable Wrench
2.5mm Hex Key
Measuring Tape
Phillips Head Screwdriver
Safety Glasses
Silicone
Soft Jaw Pliers
1
2
6
5
4
3
11
13
12
14
SUPPLY
HOSES
7
8
10
9
15

3
Installation
1) Mount Faucet: Install faucet (A)
and faucet ange (B) to deck sur-
face.
8) Connect Pull-Down Hose:
Attach quick disconnect adapter
(B) to the pull-down hose adapter
(A). Arrows on adapter ring must
be aligned with quick disconnect
release tabs for full engagement.
Note: Press both quick discon-
nect release tabs to easily discon-
nect adapters.
11) Connect Water Supply Lines:
Connect hot supply hose (on left
side) and cold supply hose (on
right side) to supply outlets.
Notes:
DO NOT use plumber putty
or plumber tape on ttings
with face seal washers or o-ring
seals.
DO NOT OVERTIGHTEN ttings
with face seal washers or o-ring
seals.
12) Flush Supply Lines:
Remove wand (B) from pull-down
hose tting (A). With faucet
handle in the off position, turn on
supply outlets.
9) Orient guide (D) so arrow is facing
upward. Slide bottom of guide
onto pull-down hose before
attaching top of guide.
10) Attach counterweight (C) to pull-
down hose. Slide counterweight
over top of guide. Push counter-
weight down so it holds guide.
2) Optional Deck Plate Install:
Assemble deck plate (C), gasket
(D) and deck plate shanks (E).
Place deck plate assembly onto
three hole deck surface.
3) Optional Deck Plate Install:
Once deck plate is centered,
hand tighten mounting nuts (F) to
secure.
4) Optional Deck Plate Install:
Install faucet (A) and faucet ange
(B) to deck plate surface.
5) Secure Faucet Mounting Hard-
ware: From below deck, slide
plastic washer (B) and metal
washer (C) onto threaded faucet
body (A)..
6) Thread mounting nut (D) onto
faucet body.
7) Secure mounting hardware to
deck with mounting screws (E).
Note: Hoses have been removed for
clarity.
A
B
OPTIONAL DECK PLATE
11
D
E
2
2
F
C
3
A
B
B
C
A
1
2
D
3
E
D
1
A
B
QUICK
DISONNECT
RELEASE TABS
ADAPTER
RING
C
D
3
2
ARROW ON
GUIDE MUST
FACE UPWARD
COLD
SUPPLY
HOT
SUPPLY

4
Installation
Maintenance
1) Remove Cartridge: Remove lever
(A) from handle hub (C) with soft
jaw pliers as to avoid damaging
nish on lever handle. Use 2.5mm
hex key to remove set screw (B)
from handle hub.
3) Remove decorative collar (D).
4) Remove compression nut (E).
5) Remove cartridge (F) from faucet
body. Inspect cartridge for debris
and replace cartridge if necessary.
2) Remove handle hub (C) from
faucet.
13) Slowly pull handle (C) forward to
the cold position, then back to
the hot position. Check for leaks,
debris and foreign matter.
Note: Faucets purchased before
XX/2020
feature 45 degree handle
rotation, forward and backward.
Suggested minimum distance to
backsplash or nished wall is 4”
(102mm).
6) Replace Cartridge: Orient cartridge
so pegs align with holes in faucet
body (see illustration to the left for
reference).
7) To install cartridge, reverse steps
1-5 in the Remove Cartridge section
above.
Note: Faucets purchased before
XX/2020
feature rotated cartridge rientation
(see illustration below for reference).
14) After faucet supply lines have
been ushed, install wand to pull-
down hose tting.
A
B
C
IMPORTANT: Soft jaw pliers must be
used on lever handle to avoid damaging
decorative nish.
2
1
A
B
C
3
D
4
E
F
5
(2x)
HOLES
FOR PEGS
(2x) PEGS
CARTRIDGE
BOTTOM VIEW
(2x)
HOLES
FOR PEGS
(2x) PEGS
CARTRIDGE
BOTTOM VIEW
FAUCETS
PURCHASED
BEFORE
XX/2020

Problem Cause Solution
Faucet no longer maintains
accurate temperature.
Foreign matter such as copper
chips, sand, stones, etc. clogging
the cartridge ports and/or
damaging the sealing surfaces of
the cartridge.
Remove cartridge and inspect
for debris. Replace cartridge if
necessary.
Flow is irregular. Accumulation of sediment in
cartridge.
Remove cartridge and inspect
for debris. Replace cartridge if
necessary.
Same as above. Accumulation of sediment in
spray wand. Remove and clean spray wand.
Pull-down hose will not retract. Pull-down hose is not properly
weighted to allow hose to retract.
Install counterweight to
pull-down hose or adjust
counterweight.
Handle is loose. Set screw has loosened. Tighten set screw.
Finish is spotting. Elements in water supply may
cause water staining on finish.
Clean finished trim area with
a soft cloth using mild soap
and water or a non-abrasive
cleaner and then quickly rinse
with water.
Troubleshooting Chart
Symmons Industries, Inc. ■31 Brooks Drive ■Braintree, MA 02184 ■Phone: [phone] ■ Fax: [phone]
Copyright © 2023 Symmons Industries, Inc. ■symmons.com ■[e-mail] ■ZV-3749 REV 0 ■ 060623