Symmons Symmetrix S2502 Series Manual

Caution: Be sure to turn off hot and cold water supplies before
installing or servicing faucet.
Installation
1. Push faucet supplies with rubber gasket through holes
in sink (make sure gasket [LL-126] is between faucet
and sink). Secure faucet to sink by tightening ange
nuts (LL-125) from underside. (If sink or counter
surface is uneven, use putty or sealant to make proper
seal under base.)
2. Connect hot supply to le tube and cold supply to
right tube using appropriate connectors.
3. Push Pop Install: Insert drain body (L) into drain
opening. From below, Tighten locking nut (O) with
gasket (M) and washer (N) to ange. Tighten tail nut
(Y) with washer (X) to secure tail pipe (Q).
DO NOT overtighten.
4. It is very important to thoroughly ush the supply
lines to prevent foreign matter, i.e. copper chips, sand,
stones, etc. from damaging the sealing surfaces of car-
tridge. Remove aerator and open hot and cold to full
open then open both supplies. Let water run through
hot and cold long enough to ush supply lines thor-
oughly. Shut o faucet and replace aerator. Check for
leaks.
Replacing handle
1. Remove screw from top of handle. Remove red or blue
washer and then remove handle (LL-122) or (LL-123).
2. Reassemble handle (LL-122) or (LL-123) in reverse
fashion.
Replacing cartridge
1. Remove screw from top of handle. Remove red or blue
washer and then remove handle (LL-122) or (LL-123).
2. Unthread cartridge cover (LL-127) from faucet.
3. Place wrench on cartridge (LL-124) hex nut, turn
wrench counter clockwise until cartridge is removed.
4. Install new cartridge (LL-124). Turn cartridge with
wrench until cartridge does not turn easily then turn
1/4 to 1/2 turn further.
5. Reassemble cartridge cover (LL-127).
6. Reassemble (LL-122) or (LL-123) handle in reverse
fashion.
Lavatory Faucet S2502 Series
Operation & Maintenance Manual
S2502PPLWG
S2502PP
Symmetrix®
1
2
3
Plumbers Putty L
Q
X
N
Y
O
M

Dimensions Symmetrix Lavatory Faucet, S2502 Series
Note: Dimensions subject to change without notice.
LWG handle Standard handle
1/2” - 14 NPSM
1-3/8”
35mm
max
Lever handle
repair kit
LL-122
Vandal proof
aerator and
removal tool
Wing handle
repair kit
LL-123
Cartridge cover
LL-127
Cartridge (2)
LL-124
Gasket
LL-126
Flange nut (2)
LL-125
Push Pop Drain Assembly
RL324*
Grid Drain Assembly
P-26
Reference chart
Parts Assembly Symmetrix Centerset Lavatory Faucet, S2502 Series
*
Note: When ordering replacements parts for
faucets with an optional decorative nish, append
appropriate three letter nish sufx code to part
numbers marked with an asterisk (*
).
Ordering replacement parts:
Call Symmons customer service at [phone],
[phone] M-F 8:00 am - 7:30 pm EST or
check our website at www.symmons.com for a
list of Symmons distributors.
Part Number
Standard Vandal Resistant
Aerator with removal tool
Removal tool part number, LL-60K
Aerator
(ow regulator)
2.2 gpm (8.3L/min) LN-15*LN-101*
1.5 gpm (5.7L/min) FLR-110-1.5* ----
1.0 gpm (3.8L/min) FLR-110-1.0* ----
.5 gpm (1.9L/min) ---- LN-100*
Symmons Industries, Inc. ■31 Brooks Drive ■Braintree, MA 02184 ■Phone: [phone] ■ Fax: [phone]
Copyright © 2023 Symmons Industries, Inc. ■symmons.com ■[e-mail] ■ZV-3839 REV 0 ■ 102023
WARNING: This product can expose you to chemicals including lead, which is known to the state of California to
cause cancer, birth defects, or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.