Symmons identity 6700 Manual

Identity™
Model Numbers
6700, 6701, 6702
Operation & Maintenance Manual
Specification
Modifications
Note: Append appropriate -sux to model number.
6700
Identity Tub/Shower System
6701
Identity Shower System
6702
Identity Tub/Shower System
6700
Tub/shower system powered by the Temptrol®
pressure-balancing valve. Features adjustable stop
screw to limit handle turn. Components made from
metal and nonmetallic materials, plated in standard
polished chrome finish.
6701
Shower system powered by the Temptrol®pressure-
balancing valve. Features adjustable stop screw to
limit handle turn, 1 mode showerhead with easy to
clean rubber nozzles and standard 2.5 gpm (9.5
L/min) flow restrictor. Components made from
metal and nonmetallic materials, plated in standard
polished chrome finish.
6702
Tub/shower system powered by the Temptrol®
pressure-balancing valve. Features adjustable stop
screw to limit handle turn, diverter tub spout, 1
mode showerhead with easy to clean rubber nozzles
and standard 2.5 gpm (9.5 L/min) flow restrictor.
Components made from metal and
nonmetallic materials, plated in
standard polished chrome finish.
-1.5 1.5 gpm (5.7 L/min) flow restrictor
-2.0 2.0 gpm (7.6 L/min) flow restrictor
-143 3 mode showerhead
-145 5 mode showerhead
-231 2 mode showerhead
-CHKS Integral check stops - for use in
installations where a positive shut-
o device is used downstream of
mixing valve
-IPS 1/2" female IPS connections
-L/HD Less showerhead
-LP Loop handle
-LR Lever handle
-OP 13" oval plate
-REB-TRM Rebuild trim kit
-REV Reverse coring, hot on right, cold
on left, for back to back installations
-SS Slip spout on any tub/shower unit
-STN Satin Nickel finish
-TRM Trim only, valve not included
-X Integral service stops - allows water
shuto at valve for service
CG
Compliance
Certied by
CSA Group
For California Residents
WARNING: This product contains chemicals known
to the State of California to cause cancer, birth de-
fects, or other reproductive harm.
-ASME A112.18.1/CSA B125.1
Limited Lifetime - to the original end
purchaser in consumer/residential
installations.
10 Years - for commercial/industrial
installations. Refer to
www.symmons.com/warranty for
complete warranty information.
Warranty

2
Dimensions
Measurements
A 5-7/8", 149 mm
B 4-5/8", 117 mm
C 3-1/2", 89 mm
D 2-7/8", 73 mm
E Ref. 77", 1956 mm
F
Shower Valve Hole Size
Min. Ø 3", 76 mm
Max. Ø 4", 102 mm
G 3-1/2", 89 mm
H 12", 305 mm
I
Rough-in
2-3/8" ± 1/2", 60 mm ± 13
mm
J
Male 1/2" NPT fitting must
protrude 4" (102 mm)
from finished wall
K
6700, 6702
Ref. 32", 813 mm
6701
Ref. 42", 1067 mm
L 5-1/4", 133 mm
M Ø 2-1/2", 64 mm
N Ø 3-1/8", 79 mm
Notes:
1) All dimensions measured from nominal rough-in (see I as reference).
2) Dimensions subject to change without notice.
FLOORFLOOR
KK
EE
FF
DD
AA MM
NN
JJ
LL
II
BB
CC
GG
OO
PP
HH

3
Parts Breakdown
HOT
Water Supply
COLD
Water Supply
A
B
C
D
E
F
GH
H
I
J
*Note: Append -STN to part number for
Satin Nickel finish.
Replacement Parts
Description Part Number
A Showerhead 672SH*
B
C
Shower Arm
Flange 300S*
D
E
Handle
Set Screw RTS-084*
F Dome Cover T-19*
G
H
I
Shower
Escutcheon Kit 6700-ESC*
J Tub Spout 054*
Tools Required for Installation
Adjustable
Wrench
Allen Wrench
3/32"
Phillips Head
Screwdriver
Plumber Tape
Silicone
Notes:
1) Apply a bead of silicone around the perimeter of all shower
trim installed flush to the finished wall (less mounting plates and
brackets).
Leave opening on bottom of escutcheons for weep hole.
2) Apply plumber tape to all threaded connections.

4
Note:
For valve body installation,
please see valve body manual.
1
H
I
H
2
1) Install shower mounting plate
(I) to shower valve. Secure with
two screws (H).
2) Attach shower escutcheon (G)
to shower mounting plate (I).
G I
Note: Tabs should snap into
place.
3) Install dome cover (F) to show-
er valve by turning clockwise.
F
G
1
2
D
1
E
2
4) Install shower handle (D) to
shower valve. Secure shower
handle with set screw (E).
5) Install tub spout (J) to pipe fit-
ting Turn clockwise to tighten.
J
1
2
Note: Handle should be facing
the 6 o’clock position.
6) Attach shower arm (B) and
flange (C) to vertical shower
pipe. Turn clockwise to tighten.
1
1
2
3
C
B
7) Install showerhead (A) to
shower arm (B). Turn clockwise
to tighten.
1
B
1
A
2
Installation

Symmons Industries, Inc. ■31 Brooks Drive ■Braintree, MA 02184 ■Phone: [phone] ■ Fax: [phone]
Copyright © 2017 Symmons Industries, Inc. ■symmons.com ■[e-mail] ■ZV-3196 REV C ■ 080522
Problem Cause Solution
Finish is spotting. Elements in water supply may cause
water staining on finish.
Clean finished trim area with a
soft cloth using mild soap and wa-
ter or a non-abrasive cleaner and
then quickly rinse with water.
Troubleshooting Chart
Operation (Temperature Control)
1) Turn shower handle counter-
clockwise approximately
1/4 turn to put valve in cold
position.
2) Turn shower handle counter-
clockwise approximately 1/2
turn to put valve in warm
position.
3) Turn shower handle counter-
clockwise approximately
3/4 turn to put valve in hot
position.
Operation (Diverter Control for 6702 only)
1) Diverter lever in down position
for tub spout operation.
2) Diverter lever in up position for
shower operation.