T&S B-0133-B User manual

Limited One Year Warranty
T&S warrants to the original purchaser (other than for purposes of resale)
that such product is free from defects in material and workmanship for a pe-
riod of one (1) year from the date of purchase. During this one-year warranty
period, if the product is found to be defective, T&S shall, at its option, repair
and/or replace it. To obtain warranty service, products must be returned to.....
T&S Brass and Bronze Works, Inc.
Attn: Warranty Repair Department
2 Saddleback Cove
Travelers Rest, SC 29690
Shipping, freight, insurance, and other transportation charges of the product
to T&S and the return of repaired or replaced product to the purchaser are
the responsibility of the purchaser. Repair and/or replacement shall be made
within a reasonable time after receipt by T&S of the returned product. This
warranty does not cover items which have received secondary finishing or
have been altered or modified after purchase, or for defects caused by physi-
cal abuse to or misuse of the product, or shipment of the products.
Any express warranty not provided herein, and any remedy for Breach of
Contract which might arise, is hereby excluded and disclaimed. Any implied
warranties of merchantability or fitness for a particular purpose are limited to
one year in duration. Under no circumstance shall T&S be liable for loss of use
or any special consequential cost, expenses or damages.
Some states do not allow limitations on how long an implied warranty lasts
or the exclusion or limitation of incidental or consequential damages, so the
above limitations or exclusions may not apply to you. Specific rights under this
warranty and other rights vary from state to state.
P/N:
DATE:
DRAWN:
CHECKED:
APPROVED:
098-014497-45 REV. 6
04-26-12
TEH
JRM 06-13-12
JHB 06-21-12
PRE-RINSE UNIT
B-0133 Series
(B-0133-B, Pre-Rinse
Unit w/Wall Bracket)
Installation and
Maintenance
Instructions
Step 1:
Apply plumber’s putty to backside of body and
insert into mounting hole. Line up water supply
lines and couplings, attach and tighten with
wrench.
Step 4:
Grab riser assembly and lower the EasyInstall®
end-fitting into faucet body. Press down until the
end-fitting “pops” in.
Step 2:
Apply plumber’s tape to top of riser threads and
attach to spring assembly. Tighten with wrench.
Step 3:
Make sure that the EasyInstall® locking washer is
seated properly inside the faucet body.
Step 5:
Lock the EasyInstall® locking nut in place and
tighten with wrench.

323334353637
36
23
31 17
19
20
16
15
11
12
13
14
10
7
5
4
3
1
9 8
2
6
3839
18
21
20
22
26
27
29
30
28
40
24
25
42
41
43
Base Faucet Assembly
1
2
3
41
42
4
5
6
7
8
9
10
Base Faucet Assembly
Faucet Body Assembly
Faucet Base Asm w/ Cerama Cartridge
Asm, Spindle - Hot w/ Spring Check
Hot Cartridge Only w/ Spring Check
Asm, Spindle - Cold w/ Spring Check
Cold Cartridge Only w/ Spring Check
Cerama Cartridge w/ Check Valve, RTC
Cerama Cartridge w/ Check Valve, LTC
Handle, Lever - Blank
Screw, Handle
Index, Button - Hot (Red)
Index, Button - Cold (Blue)
Washer
Asm, Coupling Flange
Lock Washer, EasyInstall®
014209-40
015068-40
002712-40
012443-40
002711-40
012442-40
011311-25
011312-25
001638-45
000922-45
001661-45
001660-45
001019-45
00AA
014200-45
Riser Assembly
11
12
13
14
15
43
Riser Assembly, 18”
Nipple, 3/8” x 18”
Swivel Assembly, EasyInstall®
Swivel Piece
O-Ring, Swivel Piece
Asm, Finger Hook & Screw
Wall Bracket, 6” (add -B to model no. for wall bracket)
000369-40
EZ-K
N/A
001065-45
004R
B-0109-01
Pre-Rinse Unit
16
17
18
19
Pre-Rinse Assembly
Spring, Body
Spring, Overhead
Asm, Flex Stainless Steel Hose
Asm, Spray Valve
000821-40
000888-45
B-0044-H
B-0107
Spray Valve Assembly
20
21
22
23
24
25
26
27
28
29
30
Asm, Hold Down Ring & Washer
Washer
Ring, Hold Down
Body, Spray Valve (No Handle)
Handle
Nut, Handle
Screw, Handle
Nipple
Cup, Spray
Ring, Sprayhead
Sprayface
Screw, Sprayface
010476-45
000907-45
000065-40
001120-45
003198-45
003199-45
000694-40
000019-40
007861-45
001121-45
000913-45
Bonnet Assembly
31
32
33
34
35
36
37
38
39
40
Asm, Bonnet
Stem
Washer, Seat
Washer, Bonnet Binding
Bonnet
Washer, Bonnet Brass
Stem, Packing
Spring, Bonnet
Push Button
Grease Pack (O-Ring Lubricant)
002856-40
009306-20
012915-45
001040-45
000608-25
000974-45
001100-45
000895-45
000753-25
012665-45
*
*
*
*
*
*
*
*
*
*
* Parts included in B-10K parts kit
Set Screws (2)
Clamp
Screws (2)
OPTIONAL (-B Models)
Wall Bracket Installation:
1. Fasten wall flange to wall using wall mount screws
2. Place 2-piece clamp assembly around riser and tighten
clamp screws securely.
3. Tighten set screws securely.