Teknik 5427412 User manual

NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
Lot # 566952 10/08/21
Purchased: __________________
Storage Cupboard
Hudson Elm finish | Model 5427412
English pg 1-17
Français pg 18-20
Español pg 21-23
Teknik
www.teknikoffice.co.uk

Table of Contents Assembly Tools Required
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Hardware Identification
Part Identification
Hardware Usage Guide
Assembly Steps
Français
Español
Safety
Warranty
2
3
5
4-17
18-20
21-23
24-26
27
42S SILVER 7/8" MACHINE SCREW - 4
10M TOUCH-UP PEN - 1 1R METAL PIN - 4
11S BLACK 1/2" FLAT HEAD SCREW - 8
4I DOOR
STOP - 2
2R RUBBER
SLEEVE - 4
13H HINGE - 4WOOD DOWEL - 16
42F PULL - 2 202K
Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
LEVELER - 4
46E
Page 2
TWIST-LOCK®
FASTENER COVER - 12
125P

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A RIGHT END (1)
B LEFT END (1)
C TOP (1)
D BOTTOM (1)
E BASE (1)
F ADJUSTABLE SHELF (1)
G BACK (2)
H DOOR (2)
A
B
C
D
E
F
G
G
H
H
Page 3

Step 1
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å Insert six WOOD DOWELS (42F) into the exact holes
shown in the LEFT END (B).
å NOTE: You may need to gently tap the WOOD DOWEL in
with your hammer.
B
42F
42F
Page 4

å Fasten the BACKS (G) to the LEFT END (B). Tighten four
TWIST-LOCK® FASTENERS.
å NOTE: Be sure the WOOD DOWELS in the LEFT END
insert into the BACKS.
Hardware Usage Guide
1. Insert the dowel end of the FASTENER into the
hole of the adjoining part.
NOTE: The dowel end of the FASTENER must
remain fully inserted in the hole of the adjoining
part while locking the FASTENER.
2. Tighten the FASTENER with a Phillips
screwdriver as tight as possible.
Dowel end
2.
Push a TWIST-LOCK® FASTENER
into the large hole in the part.
1.
HOW TO USE A TWIST-LOCK®FASTENER
Step 2
B
G
G
Surface with
TWIST-LOCK®
FASTENERS
Surface with
TWIST-LOCK®
FASTENERS
Surface with
TWIST-LOCK®
FASTENERS
Page 5

Step 3
å Fasten the BOTTOM (D) to the LEFT END (B). Tighten two
TWIST-LOCK® FASTENERS.
å NOTE: Be sure the WOOD DOWELS in the LEFT END
insert into the BOTTOM.
B
D
Surface with
TWIST-LOCK®
FASTENERS
Edge with TWIST-LOCK® FASTENERS
Just think. The sooner
you do this, the sooner
you do something else.
Page 6

å Insert six WOOD DOWELS (42F) into the exact holes
shown in the RIGHT END (A).
å NOTE: You may need to gently tap the WOOD DOWEL in
with your hammer.
Step 4
A
42F
42F
Page 7

Step 5
å Fasten the RIGHT END (A) to the BOTTOM (D) and
BACKS (G). Tighten six TWIST-LOCK® FASTENERS.
å NOTE: Be sure the WOOD DOWELS in the RIGHT END
insert into the BACKS and BOTTOM.
A
D
G
G
Page 8

å Using your hammer, gently tap four LEVELERS (46E)
completely into the holes in the ENDS (A and B).
å NOTE: Adjustments to the LEVELERS will be made later in
assembly once your unit is standing upright.
Step 6
A
B
46E
Page 9

Step 7
å Fasten the BASE (E) to the ENDS (A and B) and the
BOTTOM (D). Tighten four TWIST-LOCK® FASTENERS.
A
B
D
E
Page 10