TECO TR 10 User manual

TECO TR/TC 10, 15, 20 –RESET GUIDE
Chiller Reset Instructions

Important SafetyPrecautions
It is recommended that you plug the chiller into an
RCD (residual current device) at all times. Do not
operate SeaChill chillers or any accessory to SeaChill
chillers (heater or UV sterilizer) without water flow, or
overheating of lamp or heater may occur.
After installation, monitor unit for at least an hour to
confirm there are no leaks.
To avoid potential electric shock, care should be taken since
aquarium equipment involves use of electricity and water. For
each of the following situations, do not attempt repairs by
yourself; return the appliance to an authorized service facility
for service or discard theappliance:
1. Unplug chiller from wall outlet before installation of
Heater. Only plug chiller in when directed to by the
installation instructions.
2. If electrical components of the chiller or Heater get
wet do not plug in until thoroughly dried
3. Examine the Heater closely after installation. Do not
plug in if there is water on parts not intended to be
wet.
4. Do not operate chiller or Heater if it has a damaged
cord or plug, or if it is malfunctioning or damaged in
any manner.
5. Close supervision is necessary when any appliance is
used by or near children.
6. Always unplug the chiller from an outlet when before
putting on or taking off parts, and before cleaning.
Never yank cable to pull plug from outlet. Grasp the
plug and pull to disconnect.
7. Do not use the Heater for other than intended use.
The use of attachments not recommended or sold
by the Heater manufacturer may cause an unsafe
condition.
8. Do not install or store the Heater where it will be
exposed to the weather or to temperatures below
freezing.
9. Make sure the Heater is properly installed before use.
10. If an extension cable is required, use a cable with a
proper rating. A cable rated for lower amps/wattage
than the chiller with Heater may overheat. Care should
be taken to arrange the cable so that it will not be
tripped over or pulled.
KEEP THESE INSTRUCTIONS

Contact
TradeMark Aquatics Ltd is the UK distributor for Seachill.
For technical support, safety concerns, or sales, contact:
Tel: [phone]
[e-mail]
www.trademarkaquatics.co.uk
Parts & Tools
Parts needed for Heater installation.
Cable ties for wiring (6)
Tools needed:
Tongue and groove pliers or similar

Unscrew the Ring Nuts and remove the shut off valves from
the chiller.
Use tongue and groove pliers or similar to loosen plastic nuts
holding the housing in place. It is not necessary to grip nuts
tightly, a loose grip will help prevent scarring of plastic. If
desired, a piece of duct tape may be used to cover the teeth of
the channel lock pliers to prevent scarring of the plastic nuts.
Once loosened, manually remove the plastic nuts.
Step 1
Removing The Shutoff Valves

Remove air filter from chiller housing.
Pull upwards on rear of chiller housing, loosening it on the
frame of the chiller.
Insert fingers between housing and frame of the chiller at
the front. Once fingers are between frame and housing,
lift upwards.
Lift housing off of chiller frame
Step 2
Removing Filter / Housing

1
2
3
4
5
6
7
8
• Plug in and turn on the chiller
• At the top of the control panel, above the display and
controls are a series of small metal prongs. Remove
the plastic ‘jumper’from prongs 1-2 or 4-5.
• Place jumper on pins 7-8 momentarily.
• Remove jumper from pins 7-8.
• Replace the jumper to its original location.
• Now turn off your chiller.
Note: Resetting your chiller will change your set
temperature back to the default of 23°C.
CAUTION: Leaving chiller on for extended periods of time with
no water flowing will cause the unit to overheat.
UV Jumper
(Position may vary depending on whether UV is installed
- shown in the “no UV position”)
Heater Jumper
(Position may vary depending on whether heater is installed
- shown in the “no Heater position”)
Resit Pins
( Place jumper here
momentarily to Reset )
S tep 3
Resetting Chiller
Front
of
Chiller

• It is important to line up housing with the control panel. If the control panel does not fit the
slot designed for the control panel, housing is not seated correctly.
• Press down firmly on the rear of the housing. You will feel the housing snap into place.
• Replace plastic nuts over threaded inlet and outlet ports. Tighten with tongue and
groove pliers (or similar). Replace shut-off valves.
• Chiller is now ready for operation. Once water is flowing through chiller, check carefully for
any leaks.
Step 4
ReplacingtheHousing