Teknion Interpret User manual

Sliding Worksurface Kit (WWSSL), Sliding Worksurface (WWWRS) Part and Product Identification
Section:
Description: Page No:
Date:
Rev. No: 4
SLIDING WORKSURFACE KIT, SLIDING WORKSURFACE AND FRAME - DOUBLE SIDED
FRAMES, SUPPORTS AND WORKSURFACES
Sept 2017 1 of 10
INT_005a
interpret Installation Guides
A - Double Sided Frame - type and
quantities as per order
B1 - Sliding Worksurface Track
(A16-4964) x 1
B2 - Sliding Bushing
(B02-0377) x4
B3 - Disengagement Washer
(B02-0378) x4
B4 - 1/4 - 20 X 1.25 Pan Head,
Quadrex, Screw
(E01-0182) x4
B5 - 5/16-18X2 Long, Socket Head,
Cap Screw
(E01-0764) x3 or x5
B6 - 5/16-18X1/2 Hex Nut, AF, .265
Nut (E01-0755) x3
B7 - Sliding Worksurface Standoff
(B02-0383) x3
C1 - Sliding Worksurface Lock
Assembly (N02-2105) x1
C2 - 1/4-20X30mm Murakoshi Bolt
(E03-0444) x2
WWSSLD
WWWRS
E - Sliding Worksurface
(WWWRS) x2 per Frame
Angled Leg Frame shown
A
E
B2
B5
B1
B7
A
C2
C1
A
NOTE: The Cantilevers
included in the Double
Sided Frame Assembly
(A16-4882\12) are not
required for this
application.
N02-2054 x2N02-2105 x2

STEP 1b: For sizes 78" and 84", Cantilevers are added in between the two Sliding Worksurface
Tracks approximately 32" apart (can be adjusted for different Power Management Accessories).
Use the Worksurface Spacers included in the Frame Assembly to secure the Cantilevers.
Section:
Description: Page No:
Date:
INSTALL SIDING WORKSURFACE TRACKS INSTALL SLIDING TRACKS AND CANTILEVERS
INT_005a
2 of 10
Sept 2017
SLIDING WORKSURFACE KIT, SLIDING WORKSURFACE AND FRAME - DOUBLE SIDED
FRAMES, SUPPORTS AND WORKSURFACES
interpret Installation Guides
STEP 1a: Build Double Sided Frames, layout as per specification drawing. (Refer to Installation
Guide INT_002 for instructions).
Line up Sliding Worksurface Tracks so their outside holes line up with the holes on Cross
Beams. Fasten with Socket Screws and Nuts. Do not over tight!
B6
B5
Align
holes
B1
A
IMPORTANT: If Recessed Mid-Gable
Reinforcement WWSMG is specified.
Please refer to Installation Guide 011b
before continue to STEP 2
Align
holes
Approx. 32"
B6
B5
B1
A
A
A
NOTE: Only for sizes 78" and 84".
Cantilevers DO NOT attach to
Worksurfaces.

Section:
Description: Page No:
Date:
INSTALL STANDOFFS AND SPACERS DETAIL
INT_005a
3 of 10
Sept 2017
SLIDING WORKSURFACE KIT, SLIDING WORKSURFACE AND FRAME - DOUBLE SIDED
FRAMES, SUPPORTS AND WORKSURFACES
interpret Installation Guides
STEP 2: Place Sliding Bushing on the top of Sliding Worksurface Pads, in position away from
user sides. Clip Sliding Worksurface Standoffs on the top of Clamp Brackets and Standoffs as
shown. Clip Standoffs with Worksurface pads installed in the middle of outside Traverse
Beams and place Worksurface Spacer Block on top of the Traverse Beam, providing
enough clearance to install Electrical Module. (Refer to INT_002 Installation Guide).
NOTE: Use cut-out in Sliding Worksurface Pad to place Sliding Bushing. Use double channels
on the top of Clamp Brackets and Spacers to install Sliding Worksurface Standoffs.
B2
B7
A
A
NOTE: Refer to INT_002 Installation
Guide for the installation of Part A
NOTE: The Worksurface Spacer
Block is installed in the center of
Transverse Beam. Please move away as
shown on illustration if there is an
interference with Electrics.

Section:
Description: Page No:
Date:
INSTALL CENTRAL RAIL INSTALL CENTRAL RAIL
INT_005a
4 of 10
Sept 2017
SLIDING WORKSURFACE KIT, SLIDING WORKSURFACE AND FRAME - DOUBLE SIDED
FRAMES, SUPPORTS AND WORKSURFACES
interpret Installation Guides
STEP 3a: Assemble Central Rail as per INT_002, step 17. Move Bolts inside the rail to line
them up with holes of Clamp Brackets and holes in Spacer Brock.Drop it on the rail.
A
STEP 3b: Assemble Central Rail as per INT_002, step 17. Move Bolts inside the rail to line
them up with holes of Cantilever Bracket and holes in Spacer Brock.Drop it on the rail.
A

Section:
Description: Page No:
Date:
SECURE IN PLACE SECURE IN PLACE
INT_005a
5 of 10
Sept 2017
SLIDING WORKSURFACE KIT, SLIDING WORKSURFACE AND FRAME - DOUBLE SIDED
FRAMES, SUPPORTS AND WORKSURFACES
interpret Installation Guides
STEP 4b: Add the underside Spacer Block. Secure Blocks and Rail in place using Nuts
provided.
A
UNDERSIDE VIEW
STEP 4a: Add the underside Spacer Block. Secure Blocks and Rail in place using Nuts
provided.
A
UNDERSIDE VIEW

Section:
Description: Page No:
Date:
LEVEL, SQUARE AND INSTALL LEVELER COVERS
Sept 2017 6 of 10
INT_005A
SLIDING WORKSURFACE KIT, SLIDING WORKSURFACE AND FRAME - DOUBLE SIDED
FRAMES, SUPPORTS AND WORKSURFACES
interpret Installation Guides
STEP 5: Level and square the whole assembly. Tighten Screws and Nuts. Lock each leveler and remove tape so Leveler Cover can slide down.
A
Lock Levelers
Remove tape so
Leveler Cover can
slide down.

Section:
Description: Page No:
Date:
INSTALL WORKSURFACES DETAIL
INT_005a
7 of 10
Sept 2017
SLIDING WORKSURFACE KIT, SLIDING WORKSURFACE AND FRAME - DOUBLE SIDED
FRAMES, SUPPORTS AND WORKSURFACES
interpret Installation Guides
STEP 6: Place Worksurfaces with pilot holes over each Bushing. Attach Disengagement
Washer and Bushing to Worksurface using Pan Head Screw provided. Repeat with remaining
Bushings and Worksurfaces. See the detail on the next page.
E
B3
B4
NOTE: Install Peninsula Support
Kit and Peninsula Worksurface
first if specified. Refer to
Installation Guide No. INT_006a
and INT_006b for Information.
NOTE: For sizes 78 and 84,
cantilevers DO NOT attach to
Worksurface.
B4
B3
B2

Section:
Description: Page No:
Date:
SLIDE WORKSURFACE OUT
Sept 2017 8 of 10
INT_005a
SLIDING WORKSURFACE KIT, SLIDING WORKSURFACE AND FRAME - DOUBLE SIDED
FRAMES, SUPPORTS AND WORKSURFACES
interpret Installation Guides
STEP 7: Slide Worksurfaces out to gain an easy access to pilot holes requires for Lock Assembly installation.

Section:
Description: Page No:
Date:
ATTACH LOCK ASSEMBLY SQUEEZE THE HANDLE
INT_005a
9 of 10
Sept 2017
SLIDING WORKSURFACE KIT, SLIDING WORKSURFACE AND FRAME - DOUBLE SIDED
FRAMES, SUPPORTS AND WORKSURFACES
interpret Installation Guides
STEP 9: Squeeze the handle of Lock Assembly.STEP 8: Attach Lock Assembly to the underneath of Worksurface using pilot holes for
location.
C1
C2
Underside View Iso Top View SQUEEZE

Section:
Description: Page No:
Date:
MORE WORKSURFACE TO LOCKED POSTION RELEASE HANDLE TO LOCK IN PLACE
INT_005a
10 of 10
Sept 2017
SLIDING WORKSURFACE KIT, SLIDING WORKSURFACE AND FRAME - DOUBLE SIDED
FRAMES, SUPPORTS AND WORKSURFACES
interpret Installation Guides
STEP 11: Release the Lock Handle to engage into cut-out in Worksurface Track.STEP 10: Holding handle in the lock posintion push Worksurface in.
KEEP SQUEEZE
RELEASE
ENGAGE