Teknion Interpret Operating and maintenance instructions

Double Access Door (WWEDD) & Audio Visual Table Tray (WWEAV) Part and Product Identification
For Customer Support please contact
[email protected]
Section:
Description: Page No:
Date:
Rev. No: 1
Feb. 2017 1 of 8
INT_410
interpret
A1 - Double Access Door
(WWEDD) x 1
A2 - Access Door Bracket
(A16-1336) x 2
A3 - 8-32 x 5/16 Machine
Screw (E01-0837) x 4
A4 - 10-32 x 1/2" Machine
Screw (E01-0770) x 4
WWTWK Shown as
Example
B1 - Clubtalk Grommet
Enclosure Subassembly
(N09-6286) x 1
B4 - Power Bar Shroud,
Clubtalk
(A16-1970) x 1
B2 - Slim Power Bar
(YEPDCH) x 1
Please Refer to CLUBtalk
Installation Guide No. 602b
for CLUB CONNECT
TechnologyInformation.
A - WWEDD x 1
B - WWEAV x 1
A
B2
B1
B5 - #10 x 0.875" LG. Screw,
Quad. Pan Washer
(E07-0077) x 4
B3 - Compact Power Bar
(YEPS) x 1
B3
B4

Section:
Description: Page No:
Date:
LOWER ACCESS DOOR TO WORKSURFACE FASTEN BRACKET
INT_410
2 of 8
Feb. 2017
interpret
STEP 1: Lower Double Access Door into the cut out of the Table.
Underside View
STEP 2: Fasten Bracket to Double Access Door with the Screws provided.
A
A2 A1 A3

STEP 4: Unhook Power Bar Shroud as shown above.
Section:
Description: Page No:
Date:
FASTEN ACCESS DOOR ASSEMBLY REMOVE POWER BAR SHROUD
INT_410
3 of 8
Feb. 2017
interpret
STEP 3: Fasten Bracket with screws provided to underside of Table.
Underside View
A4
B4
hooks hooks

Section:
Description: Page No:
Date:
INSTALLNG COMPACT POWER BAR
Feb. 2017 4 of 8
INT_410
interpret
STEP 5: Place the Power Bar into the assembly as shown above.
B3
B4

STEP 6: Slide the hooks on the Power Bars into the Clubtalk Grommet Enclosure as shown
above.
STEP 5: Place Slim Power Bar into the assembly as shown above.
Section:
Description: Page No:
Date:
INSTALLING SLIM POWER BAR INSTALLING POWER BAR
INT_410
5 of 8
Feb. 2017
interpret
B2
hooks
hooks
hooks
hooks

Section:
Description: Page No:
Date:
CONNECT THE POWER BARS
Feb. 2017 6 of 8
INT_410
interpret
STEP 7: Plug the Compact Power Bar in the Slim Power Bar.
Underside View
B4
B3
B2

Section:
Description: Page No:
Date:
FASTEN ACCESS DOOR ASSEMBLY TO WORKSURFACE
Feb. 2017 7 of 8
INT_410
interpret
STEP 8: Align Pilot Holes from underside of Worksurface to holes of Underpan. Place Underpan on underside of worksurface so 4 Sensor Holders and inserted into Access Door Assembly and
hold in place.
Underside View
Pilot Holes
NOTE: Check the doors operation by opening and
closing. Adjust position of Underpan if necessary.
Doors

Section:
Description: Page No:
Date:
FASTEN ACCESS DOOR ASSEMBLY TO WORKSURFACE
Feb. 2017 8 of 8
INT_410
interpret
STEP 9: Fasten Underpan with screws provided to underside of Worksurface.
Underside View
B5