Teknion YHRE Operating and maintenance instructions

Rectangular - Counter-Balance (YHRE), Rectangular with Split
Surface - Counter-Balance (YHRS), Corner - Counter-Balance
(YHCC), Corner with Split Surface - Counter-Balance (YHCS)
Part and Product Identification
Section:
Description: Page No:
Date:
Rev. No: 6
HEIGHT ADJUSTMENT TABLE - COUNTER - BALANCE - TROUBLE SHOOTING
HEIGHT ADJUSTMENT TABLES (COMPLEMENTS)
Sept 2019 1 of 16
COM_101d
complements Installation Guides
A - H Frame
B - #10 x 3/4" Typ.
Pan Quad
(E01-0991) x4
C - Release
Mechanism
(N09-6178) x1
E - B18.3.5M-M6 x 1.0
x12 Socket
(E01-1027) x8
F - #12 x7/8" WD
Screw Pan Quad
(E04-0087) x12
I - Worksurface
(C05-9749_N) x1
J - M10 x 1.5mm
Button Head Screw
(E01-1022) x4
K - Feet
(N09-5680) x2
M - Crank Handle
(D06-4116) x1
N1 - Wire Clip
(B02-0566) x4
R1 - Rectangular Table
Grommet
(D05-0068) x1
OPTIONAL
R2 - Worksurface
with Cut-Out
(C05-9749_R) x1
NOTE: Worksurface with
Grommet shown.
Please refer to Page 7 for
Operation Guide.
Maximum load for the
Table is 120 lbs. excluding
the Worksurface.
O - E-Chain Vertical
Wire Manager
(YEEC) x1
P - Power Bar
(I04-0116) x1
Q - YESW x1
Q1 - Self-Tap Screw
(FS8-5-16-PB) x4
Q2 - Brackets
(B03-2394)
With Cut-Out x3
Without Cut-Out x2
N2 - #6, 5/8" FHPS,
Zinc
(E07-0148) x8
D - Strut
(A16-4031) x1
K - N09-5657
OPTIONAL
R1
R2
C
D
A
K
O
P
Q2
G - 6 x 5/8" WD
Screw Flat Quad
(E04-0090) x1
H - 3/16" Wire Clamp
(B02-0598) x1
L - 1
4" Hex to 1 4" SQ
Adapter
(D06-4272) x1

Section:
Description: Page No:
Date:
INSTALL STRUTS ATTACH FEET
COM_101d
2 of 16
Sept 2019
HEIGHT ADJUSTMENT TABLE - COUNTER - BALANCE - TROUBLE SHOOTING
HEIGHT ADJUSTMENT TABLES (COMPLEMENTS)
complements Installation Guides
STEP 2: Flip H-Frame up-side-down. Install Feet to H-Frame with Screws as shown.
STEP 1: Install Struts on H-Frame with Screws as shown.
NOTE: H-Frame up-side-down.
D
A
E
K
J

Section:
Description: Page No:
Date:
WORKSURFACE ASSEMBLY
Sept 2019 3 of 16
COM_101d
HEIGHT ADJUSTMENT TABLE - COUNTER - BALANCE - TROUBLE SHOOTING
HEIGHT ADJUSTMENT TABLES (COMPLEMENTS)
complements Installation Guides
STEP 3: Keep H-Frame and Worksurface up-side-down. Align pilot holes on Struts with the Worksurface as shown, then secure them with Screws.
F
R2
F

6"
12.0
STEP 5: Secure line to worksurface 12" away from paddle.
Section:
Description: Page No:
Date:
PADDLE ASSEMBLY
SECURING THE LINE
ATTACH HANDLE HOLDER
COM_101d
4 of 16
Sept 2019
HEIGHT ADJUSTMENT TABLE - COUNTER - BALANCE - TROUBLE SHOOTING
HEIGHT ADJUSTMENT TABLES (COMPLEMENTS)
complements Installation Guides
NOTE: Please refer to Specification
Drawing for location to install Paddle.
Paddle installing on right handed side
of the Table shown.
B
C
G
STEP 6: Peel off the adhesive cover on Handle Holder, and press it onto the bottom of
Worksurface firmly 6" inside of the edge.
NOTE: Preferably locate the Handle Holder to left hand sided of the Table.
STEP 4: Align pilot holes on Paddle and Worksurface, then secure with Screws.
N1
N2
N1
N2
H

Section:
Description: Page No:
Date:
INSERT HANDLE STORE HANDLE
COM_101d
5 of 16
Sept 2019
HEIGHT ADJUSTMENT TABLE - COUNTER - BALANCE - TROUBLE SHOOTING
HEIGHT ADJUSTMENT TABLES (COMPLEMENTS)
complements Installation Guides
STEP 7b: Insert Handle into Handle Holder when not using.STEP 7a: Place Table in position. Insert the Handle as shown and rotate to set the Table
Worksurface at desired height.
NOTE: Please refer to Operation Guides for Table height adjustment instructions.
NOTE: Please refer to Operation Guides
for Table height adjustment instructions.
Underside View
M

Section:
Description: Page No:
Date:
LEVELING INSERT GROMMET & ATTACH E-CHAIN
COM_101d
6 of 16
Sept 2019
HEIGHT ADJUSTMENT TABLE - COUNTER - BALANCE - TROUBLE SHOOTING
HEIGHT ADJUSTMENT TABLES (COMPLEMENTS)
complements Installation Guides
STEP 9: Please insert Grommet into Cut-out. Peel of adhesive cover on Tube and attach
E-chain to the back of the Leg as shown.
STEP 8: Level Table by rotating Levelers under Feet.
If E-Chain is specified, please
refer to Installation Guide No.
COM_102 for information.
Detail View
LEVELER
Underside View
R1
O

Section:
Description: Page No:
Date:
BRACKET INSTALLATION (WITH GROMMET) BRACKET INSTALLATION ( WITHOUT GROMMET)
COM_101d
7 of 16
Sept 2019
HEIGHT ADJUSTMENT TABLE - COUNTER - BALANCE - TROUBLE SHOOTING
HEIGHT ADJUSTMENT TABLES (COMPLEMENTS)
complements Installation Guides
STEP 10a: Use provided self-tap Screws to fasten Brackets under the Worksurface.
NOTE: Please refer to Specification Drawing for Brackets to be use and Page 8 for Brackets location.
STEP 10b: Use provided self-tap Screws to fasten Brackets under the Worksurface.
Q1
Q2
Q1
Q2

NOTE: Make sure the Bracket will not interfere with the Cross Bar on the H-frame.
Section:
Description: Page No:
Date:
SIDE VIEW FRONT VIEW (TABLE WITH GROMMET)
FRONT VIEW (TABLE WITHOUT GROMMMET)
COM_101d
8 of 16
Sept 2019
HEIGHT ADJUSTMENT TABLE - COUNTER - BALANCE - TROUBLE SHOOTING
HEIGHT ADJUSTMENT TABLES (COMPLEMENTS)
complements Installation Guides
Q1
Q2
Q2
Q1
Q2
Q1

Section:
Description: Page No:
Date:
ATTACH POWER BAR (WITH GROMMET) ATTACH POWER BAR ( WITHOUT GROMMET)
COM_101d
9 of 16
Sept 2019
HEIGHT ADJUSTMENT TABLE - COUNTER - BALANCE - TROUBLE SHOOTING
HEIGHT ADJUSTMENT TABLES (COMPLEMENTS)
complements Installation Guides
STEP 11: Attach Power Bar into the Bracket as shown.
NOTE: Please refer to Page 10 for clipping location.
Underside View Underside View
P
P

NOTE: Make sure the Power Bar is fully clipped into the Bracket.
NOTE: The Bracket should be clipped at the center of Power Bar.
NOTE: The Bracket should be clipped at the center of Power Bar.
Section:
Description: Page No:
Date:
SIDE VIEW FRONT VIEW (TABLE WITH GROMMET)
FRONT VIEW (TABLE WITHOUT GROMMET)
COM_101d
10 of 16
Sept 2019
HEIGHT ADJUSTMENT TABLE - COUNTER - BALANCE - TROUBLE SHOOTING
HEIGHT ADJUSTMENT TABLES (COMPLEMENTS)
complements Installation Guides
Detail View
PP
P

Section:
Description: Page No:
Date:
WIRING (TABLE WITH GROMMET)
Sept 2019 11 of 16
COM_101d
HEIGHT ADJUSTMENT TABLE - COUNTER - BALANCE - TROUBLE SHOOTING
HEIGHT ADJUSTMENT TABLES (COMPLEMENTS)
complements Installation Guides
STEP 12a: Please refer to the above diagram for Cable routing for Table with Grommet.
Underside View

Section:
Description: Page No:
Date:
WIRING (TABLE WITHOUT GROMMET)
Sept 2019 12 of 16
COM_101d
HEIGHT ADJUSTMENT TABLE - COUNTER - BALANCE - TROUBLE SHOOTING
HEIGHT ADJUSTMENT TABLES (COMPLEMENTS)
complements Installation Guides
STEP 12b: Please refer to the above diagram for Cable routing for Table without Grommet.
Underside View

Section:
Description: Page No:
Date:
COUNTER-BALANCE ADJUSTMENT (INITIAL SET-UP)
Sept 2019 13 of 16
COM_101d
HEIGHT ADJUSTMENT TABLE - COUNTER - BALANCE - TROUBLE SHOOTING
HEIGHT ADJUSTMENT TABLES (COMPLEMENTS)
complements Installation Guides
CHARGING INSTRUCTIONS:
1. INSTALL THE TABLE WORKSURFACE.
2. PRESS AND HOLD THE RELEASE PEDAL.
3. WHILE HOLDING THE PEDAL, CHARGE THE TABLE IN
COUNTER-CLOCKWISE DIRECTION USING A DRILL GUN AND ADAPTER
PROVIDED.
4. STOP CHARGING ONCE THE TABLE REACHES ITS UPPER POSITION
AND RELEASE THE PEDAL. NOTE : DO NOT OVERCHARGE THE TABLE
5.TO ENSURE THE AMOUNT OF CHARGE SUFFICIENCY, HOLD THE
PEDAL; THE TABLE SHOULD MAINTAIN ITS TOP POSITION.
6. IN CASE THE TABLE DOES NOT SUSTAIN ITS TOP POSITION, APPLY
ADDITIONAL MINIMAL CHARGE.
L

Section:
Description: Page No:
Date:
PRESS TABLE USING RELEASE MECHANISM
COM_101d
14 of 16
Sept 2019
HEIGHT ADJUSTMENT TABLE - COUNTER - BALANCE - TROUBLE SHOOTING
HEIGHT ADJUSTMENT TABLES (COMPLEMENTS)
complements Installation Guides
STEP 14: Pull Paddle up to adjust height for the Counter-Balance mechanism inside the
H-Frame.
NOTE: Please refer to Step 13 on Page 14 to add or release pressure on Counter-Balance if
necessary.
STEP 13: Put pressure on Worksurface.
NOTE: Rotate Counter-Balance Adjustment
Handle toward "-" if it's too tight, rotate
toward "+" if it's too loose.
Top View
Cable Tension Nut
NOTE: In case the Release Mechanism does not work,
adjust the Cable Tension by rotating the Cable Tension
Nut counter-clockwise and then clockwise.

Section:
Description: Page No:
Date:
ADJUST HEIGHT ADDING WEIGHT
REMOVING WEIGHT
COM_101d
15 of 16
Sept 2019
HEIGHT ADJUSTMENT TABLE - COUNTER - BALANCE - TROUBLE SHOOTING
HEIGHT ADJUSTMENT TABLES (COMPLEMENTS)
complements Installation Guides
STEP 15: Bring Worksurface to desired height gently.
NOTE: Worksurface should be easy to change height. Please refer to Step 14 on Page 14 to add
or release pressure on Counter-Balance if necessary.
NOTE: Worksurface should be easy to
move up and down. Please refer to Step
2 on Page 8 to add or release pressure
on Counter-Balance if necessary.
For every 5 lbs. of weight added to the Worksurface, rotate the Handle 8 times toward "+".
NOTE: Maximum load for the Table is 120 lbs. excluding the Worksurface.
NOTE: Maximum load for
the Table is 120 lbs.
excluding the Worksurface.
8 Times
For every 5 lbs of weight removed from the Worksurface, rotate the Handle toward "-" 8 times.
8 Times

Section:
Description: Page No: 16 of 16
Date: Sept 2019
complements Installation Guides
After adjustments the table still
doesn't go up and down easily.
The table moves down easily
but is difficult to raise.
The table goes up easily but is
difficult to lower.
1. Check the Mechanism Cable is
properly routed. It should not be
stuck, pinched, broken or kinked.
2. Ensure the Paddle is not broken.
1. Rotate the Handle towards "+"
and keep checking after 3 or more
turns.
1. Rotate the Handle towards "-"
and keep checking after 3 or more
turns.
Additional Notes
1. The Counter-Balance Height Adjustable Table is shipped from the factory without pre-load. The Table is
shipped with a Handle for Counter-Balance Adjustments.
2. Proper adjustment and use of the product will maximize the benefits of the product and ensure many years of
problem free use.
3. Improper use and set up will impact the warranty.
4. If the product is not functioning properly after Troubleshooting, please contact your authorized Teknion dealer.
Maximum load for the table is 120 lbs. excluding the
Worksurface.
COM_101d
HEIGHT ADJUSTMENT TABLES (COMPLEMENTS)
HEIGHT ADJUSTMENT TABLE - COUNTER - BALANCE - TROUBLE SHOOTING