Teknion Interpret User manual

Sliding Worksurface Kit (WWSSL), Sliding Worksurface (WWWRS),
Single Sided Complete Frame (WWSSC)
For Customer Support please contact
[email protected]
Section:
Description: Page No:
Date:
Rev. No: 3
Feb 2017 1 of 19
INT_005b
interpret
A1
F
E
G
Angled Leg Frame shown
H
I
B
P7
L
T
S
Leveler Cover is
located inside Leg,
assembled and
secured in place
with tape.
D
P3
P4
P1
P8
P2
P9
P6
P5
Q1
Q2

Part and Product Identification
Section:
Description: Page No:
Date:
Rev. No: 3
Feb 2017 2 of 19
INT_005b
interpret
A1 - End Leg, Angle
Single Sided
(N02-3700) x1 Left
x1 Right
C - 1/4-20x3-1/2 Flat
Head Machine Quad
(E01-0771) x2
D - Front Standoff
(B02-0658) x1
or x2
E - Single Sided Rail
Assembly
(N02-2150) x1
G - Modesty, Single Sided
(C05-7238) x1
H - Infill Bottom Bracket
(A16-0947) x2
J - 1/4-20 UNC x0.500"
2A, Cross Square
Socket, Truss Head,
Machine Steel, Zinc
(E01-0110) x6
or x10
M - #10x0.875 Quad Pan
Washer
(E07-0077) x 6
or x12
K - #8118x1/2 Cross
Square Comb, Self
(E07-0012) x2
L - Worksurface Support
Bracket
(N09-4134) x2
or x4
A2 - End Leg, Straight
Single Sided
(N02-3698) x1 Left
x1 Right
F - Single Sided Rail Cap
(N02-2151) x2
I - Infill Bottom Bracket
Cover
(A25-0389) x2 R-Interpret Drilling
Template
(A16-1623) x1
OR
B - Transverse Beam
Assembly
(N02-3688) x1
P - (N02-2220) x2
P1 - Sliding Worksurface
Track, Single Sided
(A16-4965) x1
P2 - Sliding Bushing
(B02-0377) x2
P3 - Disengagement Washer
(B02-0378) x2
P4 - Machine Screw,
1/4-20X1" PAN,
QUADREX, BLACK
(E01-0182) x2
P5 - 5/16-18x2 Long, Socket
Head Cap Screw
(E01-0764) x1
P6 - 5/16-18 Hex Nut, 1/2
A/F, .265 Thick
(E01-0755) x1
P7 - Sliding Worksurface
Standoff (B02-0383) x4
P8 - 5/16-18x3/8 Button
Head Hex Socket Cap
Screw, Bare
(E01-0798) x2
P9 - 5/16-18 Hex Jam Nut,
0.190 Thick Zinc,
(HN03118JZ)
(E03-0551) x2
Q1 -Sliding Worksurface
Lock Assembly
(N02-2105) x1
Q2 - 1/4-20x30mm
Murakoshi Bolt
(Accurate Fasteners
JCBB) Zinc
(E03-0444) x2
O - 5/16-18 Hex Jam Nut, 0.190
Thick ZINC, (HN 03118JZ)
(E03-0551) x 4
or x 8
S - (X05-0273) x2
S4 - Gable Corner Bracket
(N09-4200) x1 Left
or x1 Right
S1 -5/16-18x3/8 Bottom
Head Hex Socket Cap
Screw, Bare
(E01-0798) x 1
S2 -5/16-18 Hex Jam Nut,
0.190 Thick ZINC,
(HN03118JZ)
(E03-0551) x 1
S3 -1/4-20 UNCx0.500"
2A, Cross/Square
COMB.Socket, TRS.
Head. Machine Screw,
Steel, Zinc
(E01-0798) x 1
T - Sliding Worksurface,
Single Sided
(WWWRS) x1
N - 5/16-18x3/8 Button Head
Hex Socket Cap Screw, Bare
(E01-0798) x 4
or x 8

Section:
Description: Page No:
Date:
NOTE: WORKSURFACE SUPPORT BRACKETS
Feb 2017 3 of 19
INT_005b
interpret
78" - 96" Frame
60" - 72" Frame
48" - 54" Frame
NOTE: Do not install inner
Worksurface Support Brackets.
NOTE: Please refer to above diagram for Worksurface Sliding Track location. For 60" to 72" width Frame, DO NOT install the inner Worksurface Support Brackets.

Section:
Description: Page No:
Date:
REMOVE NUTS AND SCREWS
Feb 2017 4 of 19
INT_005b
interpret
Do Not Remove
C1
B
End Gable Connection
Mid Gable Connection
STEP 1: Remove Screw and Nut from Clamp as shown on illustration.STEP 1: Remove Screw and Nut from Clamp as shown on illustration.

Section:
Description: Page No:
Date:
RELOCATE CLAMP
Feb 2017 5 of 19
INT_005b
interpret
Clamps at End Gable Location
Clamps at Mid Gable Location
Clamp to be removed and repositioned to
End Gable Postion
Clamps at End Gable Location
Refer to highlighted holes to
fasten Clamps for End Gable
Position.
STEP 2: Remove Clamp.