Tempo Fitness FSP200 User manual

INSTRUCTION MANUAL
Read and understand all of the instructions
and safety information in this manual
before operating or servicing this tool.
52063481 REV 6 © 2019 Tempo Communications Inc. 01/20
FSP200
Optical Fiber Fusion Splicer

FSP200
Tempo Communications Inc. 1390 Aspen Way • Vista, CA 92081 USA • 800-642-2155
2
Table of Contents
Preface 3
Important Safety Information 4
Section 1. Identication 9
Section 2. Operation 11
Setup .................................................................................................................................... 11
Splice Mode........................................................................................................................... 12
Fiber Preparation ................................................................................................................... 13
Splicing Procedure................................................................................................................. 14
Heating Protection Sleeve ...................................................................................................... 15
Cooling Tray .......................................................................................................................... 16
Splice-on Connectors ............................................................................................................. 16
Button Functions.................................................................................................................... 17
Appendixes ........................................................................................................................... 17
Section 3. Menu Operation 18
Splice Mode Menu (S–Mode) ................................................................................................. 18
Heater Mode Menu (H–Mode) ................................................................................................ 22
Maintenance.......................................................................................................................... 24
Splice Set .............................................................................................................................. 25
Data Save.............................................................................................................................. 26
Set ........................................................................................................................................ 27
Section 4. Specications 29
Section 5. Troubleshooting 30
Appendix A. FSP200 Fusion Splicer Cleaning 35
Appendix B. Practice Splicing 38
Appendix C. Tempo Communications Splice-on Connectors 39

FSP200
3
Tempo Communications Inc. 1390 Aspen Way • Vista, CA 92081 USA • 800-642-2155
Preface
Description
The Tempo Communications FSP200 Optical Fiber Fusion Splicer is intended to fuse bers, resulting in low splice loss and
long-term stable splices. Splice loss depends on certain conditions such as ber preparation, splicing parameters, and ber
condition.
The FSP200 fusion splicer uses a CDS (Core Detection System), which is also widely known as PAS (Prole Alignment System).
Two cameras sense the center of the core of the bers, with the fusion splicer then adjusting in the X, Y, and Z dimensions to
automatically and precisely align the two ber cores. A fusing arc is applied, which then provides the lowest loss fusion splice.
The FSP200 with PAS technology is designed for splicing many types of optical bers. It is small in size and lightweight, making
it suitable for any operating environment. It is easy to operate, and it splices fast while maintaining low splice loss.
Contents List
• FSP200 fusion splicer
• 250 micron adapter pair
• 900 micron adapter pair
• SC/LC splice-on connector adapter
• SOC Oven adapter
• Spare electrodes (one pair)
• AC adapter (power supply) with North American line cord
• Battery pack (installed in FSP200)
• Carry case with strap
• 1.5 mm hex wrench
• Plastic tweezers
• Cooling tray
• Electrode polisher with 10 polishing strips
• Cleaning brush
• USB Cable
• Quick reference card
• Shipping contents form
Safety
Safety is essential in the use and maintenance of Tempo Communications tools and equipment.
This instruction manual and any markings on the tool provide information for avoiding hazards and unsafe practices related to
the use of this tool. Observe all of the safety information provided.
Purpose of This Manual
This instruction manual is intended to familiarize all personnel with the safe operation and maintenance procedures for the
Tempo Communications FSP200 Optical Fiber Fusion Splicer.
Keep this manual available to all personnel.
All specications are nominal and may change as design improvements occur. Tempo Communications shall not be liable for damages resulting from
misapplication or misuse of its products.

FSP200
Tempo Communications Inc. 1390 Aspen Way • Vista, CA 92081 USA • 800-642-2155
4
Important Safety Information
General
Use this unit for the manufacturer’s intended purpose only, as described in this manual. Any other use can impair the protection
provided by the unit. Do not use the splicer on live bers.
Environmental Conditions
This tool is designed to operate at a maximum relative humidity of 95% and at altitudes up to 5000 m (16,400 ft).
Before Applying Power
Verify that the tool is set to match the available line voltage.
Do Not Operate in Explosive Atmosphere
Do not operate the tool in the presence of ammable gases or fumes.
Do Not Remove Instrument Cover
Do not remove the cover of the unit for any reason. It contains no user-serviceable parts.
SAFETY ALERT SYMBOL
This symbol is used to call your attention to hazards or unsafe practices which could result in an
injury or property damage. The signal word, dened below, indicates the severity of the hazard.
The message after the signal word provides information for preventing or avoiding the hazard.
Immediate hazards which, if not avoided, WILL result in severe injury or death.
Hazards which, if not avoided, COULD result in severe injury or death.
Hazards or unsafe practices which, if not avoided, MAY result in injury or property damage.
Read and understand all of the instructions and safety information in this
manual before operating or servicing this tool.
Failure to observe this warning could result in severe injury or death.

FSP200
5
Tempo Communications Inc. 1390 Aspen Way • Vista, CA 92081 USA • 800-642-2155
Important Safety Information (cont’d)
Electric shock hazard:
Contact with live circuits could result in severe injury or death.
Wear eye protection when using this tool.
Fiber fragments can be extremely dangerous if they come into contacts with
eyes or skin or are ingested.
Disconnect AC power cord from AC adapter inlet or wall socket (outlet) immediately if user
observes the following or if the splicer receives the following faults:
• Fumes, bad odor, noise, or overheat occurs.
• Liquid or foreign matter falls into cabinet.
• Splicer is damaged or dropped.
If these faults occur, return unit to Tempo Communications service center for repair. Leaving
splicer in a damaged state could cause equipment failure, electric shock or re, and could result
in severe injury or death.
Electric shock hazard:
• Use only AC adapter or battery charger designed for this splicer. Using an improper AC power
source could cause fuming, electric shock, or equipment damage.
• Do not disassemble or modify splicer, AC adapter, or battery. Do not remove or bypass any
electrical or mechanical device (e.g., fuse or safety switch) incorporated into design and
manufacturing of this equipment.
• Never operate tool in an environment where ammable liquids or vapors exist. Risk of re or
explosion could result from the tool’s electrical arc in such an environment.
• Do not use compressed gas or canned air to clean tool. They may contain ammable
materials that could ignite during electrical discharge.
• Do not touch electrodes when splicer is on and power is supplied to unit. The electrodes
generate high voltage and high temperatures that could cause a severe shock or burn.
• Turn tool off and disconnect AC power cord before replacing electrodes.
Failure to observe these warnings could result in severe injury or death.

FSP200
Tempo Communications Inc. 1390 Aspen Way • Vista, CA 92081 USA • 800-642-2155
6
Important Safety Information (cont’d)
Electric shock hazard: Use only proper power source.
• Check AC power source before use. Proper AC power source is 100–240 VAC, 50–60 Hz.
Proper DC power source is 10–12 VDC. Improper AC or DC power source could cause fuming,
electric shock, or equipment damage.
• AC generators commonly produce abnormally high AC output voltage or irregular frequencies.
Measure output AC voltage with a circuit tester before connecting the AC power cord. Such
abnormally high voltage or frequency from a generator could cause fuming, electric shock, or
equipment damage. Make sure generator is regularly checked and serviced.
Failure to observe these warnings could result in severe injury or death.
Electric shock hazard:
• Do not modify, abuse, heat, or excessively pull on power cord. Use of a damaged cord could
cause fuming, electric shock, or equipment damage.
• This tool uses a three-prong (core) AC power cord that contains an earthed ground safety
mechanism. This tool must be grounded. Use only the supplied power cord. Never use a two-
prong (core) power cord, extension cord, or plug.
• Connect AC power cord properly to splicer (inlet) and wall socket (outlet). When inserting
AC plug, make sure there is no dust or dirt on terminals. Engage by pressing the female plug
into the splicer (inlet) and the male plug into the wall socket (outlet) until both plugs are fully
seated. Incomplete engagement could cause fuming, electric shock, or equipment damage.
• Do not short-circuit the terminals of AC adapter and optional battery. Excessive electrical
current could cause fuming, electric shock, or equipment damage.
• Do not touch the splicer, AC power cord, and AC plugs with wet hands.
• Do not operate splicer near hot objects, in hot temperature environments, in dusty/humid
atmospheres or when condensation is present on the tool. This may result in electric shock,
splicer malfunction, or poor splicing performance.
Failure to observe these warnings could result in severe injury or death.

FSP200
7
Tempo Communications Inc. 1390 Aspen Way • Vista, CA 92081 USA • 800-642-2155
Important Safety Information (cont’d)
Battery safety:
• Do not allow anything to contact the battery terminals.
• Do not immerse batteries in liquid. Liquid may create a short circuit and damage the battery.
If batteries are immersed, contact your service center for proper handling.
• Do not place the battery into a pocket, tool pouch, or tool box with conductive objects.
Conductive objects may create a short circuit and damage the battery.
• Do not place a battery on moist ground or grass. Moisture may create a short circuit and
damage the battery.
• Do not store the battery at more than 122 °F (50 °C) or less than –4 °F (–20 °C). Damage to
the battery can result.
• Do not use another manufacturer’s charger. Other manufacturers’ chargers may overcharge
and damage the battery.
• Do not attempt to open the battery. It contains no user-serviceable parts.
Failure to observe these precautions may result in injury and may damage the unit.
• Do not store tool in areas of extremely high temperature and humidity.
• Do not touch protection sleeve or tube heater during or immediately after heating. These
surfaces are very hot and touching them may result in burns.
• Do not place tool in an unstable or unbalanced position. Tool may shift or lose balance,
causing unit to fall.
• This tool is precision adjusted and aligned. Do not allow unit to receive a strong shock or
impact. Use supplied carrying case for transportation and storage. Carrying case protects
tool from damage, moisture, vibration, and shock.
Failure to observe these precautions may result in injury and may damage the unit.
Follow these instructions for handling electrodes:
• Use only specied electrodes.
• Set new electrodes in correct position.
• Replace electrodes as a pair.
Failure to observe this precaution may cause abnormal arc discharge, which may result in
equipment damage or degradation in splicing performance.

FSP200
Tempo Communications Inc. 1390 Aspen Way • Vista, CA 92081 USA • 800-642-2155
8
• Do not use any chemical other than pure alcohol (99% or greater) to clean the objective
lens, V-groove, LCD monitor, etc. Use of other chemicals may cause blurring, discoloration,
damage, or deterioration.
• This tool requires no lubrication. Oil or grease may degrade the splicing performance and
damage the splicer.
• This equipment must be repaired or adjusted by a qualied technician or engineer. Incorrect
repair may cause re or electric shock. Contact Tempo service center for repair.
Failure to observe these precautions may result in injury and may damage the unit.
Important Safety Information (cont’d)

FSP200
9
Tempo Communications Inc. 1390 Aspen Way • Vista, CA 92081 USA • 800-642-2155
Section 1. Identication
Components of Splicer
Description of Products
2. Description and Function of Splicer
Front Side of OFS-95
Back Side of OFS-95
Output USB port Input
Wind Protector
LED
Power Unit Dock
Description of Products
2. Description and Function of Splicer
Front Side of OFS-95
Back Side of OFS-95
Output USB port Input
Wind Protector
LED
Power Unit Dock
USB Port: Used to download the splice report and to upload new rmware for upgrade and revisons.
DC Output Port: Provides a 12V DC output at 1.5A.
DC Input Port: Provides connection for the power supply or external power cord.

FSP200
Tempo Communications Inc. 1390 Aspen Way • Vista, CA 92081 USA • 800-642-2155
10
Top View
Description of Products
➢Top Side of OFS-95
➢Keypad of OFS-95

FSP200
11
Tempo Communications Inc. 1390 Aspen Way • Vista, CA 92081 USA • 800-642-2155
Section 2. Operation
Setup
Installing Battery in Splicer
The FSP200 can be powered by an external power adapter and battery.
Inserting the Battery
Remove the protective cover from the battery contacts. Insert the battery into the battery compartment until it clicks into place.
Removing the Battery
Turn off the splicer. Push the release button, located on the side of the splicer body, and remove the battery.
Two Methods of Checking Remaining Battery Capacity
• If the battery is already installed in the splicer, turn the splicer ON. The battery is automatically identied, and the
remaining battery capacity is displayed on the “Ready” screen.
• Press the battery check button on the battery pack. The remaining battery capacity is indicated on the LED indicator.
Remaining battery capacity indicator Remaining battery
5 LED 80~100%
4 LED 60~80%
3 LED 40~60%
2 LED 20~40%
1 LED Less than 10%

FSP200
Tempo Communications Inc. 1390 Aspen Way • Vista, CA 92081 USA • 800-642-2155
12
Turning Splicer ON
Press and hold until the LED on the keypad turns ON (green color).
The “Ready” screen is displayed after all the motors reset to their initial positions.
The power source type is automatically identied. If the battery is used, the remaining battery capacity is displayed.
Splice Mode
Use SM FAST splice mode for standard SM ber (ITU-TG.652) splicing. It performs splices in 7seconds and is the quickest
mode for SM ber splicing.
Use AUTO splice mode if ber type is not identied. Splice takes 2 seconds longer but it covers most conventional ber splicing
for the following reasons:
• AUTO mode rst identies ber type by analyzing ber prole, and the splicing condition is chosen for the type of
ber. The types of bers covered by AUTO are all the conventional bers, such as SMF (G652), BIF (G657), NZDSF (G655),
MMF (G651), etc. AUTO mode takes longer than the SM processes but is recommended in cases where the ber type is
not positively identied or if the user is new to fusion splicing.
• AUTO mode uses an automatic arc calibration function, which monitors the splicing process and ensures adequate arc
power for the splice.
Automatic Arc Calibration Function
When the automatic ARC calibration function is enabled the previous splice’s ARC power is used. If the ambient conditions or
type of ber has changed an ARC calibration may be required. The automatic arc calibration function works in AUTO modes
only. It is not active in the standard splice modes. When using those modes, performing arc calibration before splicing is
strongly recommended.

FSP200
13
Tempo Communications Inc. 1390 Aspen Way • Vista, CA 92081 USA • 800-642-2155
Fiber Preparation
Placing Protection Sleeve over Fiber
Place the protection sleeve over the ber. Clean optical ber with alcohol-soaked gauze or lint-free tissue approximately
100 mm (4 in) from the tip.
Note: Splice-on connectors are pre-cleaved. Do not attempt to clean the ber on the splice-on connector. Follow the instructions
supplied with the splice-on connectors.
• Clean optical ber with alcohol-soaked gauze or lint-free tissue. Dust particulates can enter
the protection sleeve, resulting in a ber break or attenuation increase.
• Make sure ber is passed through the protection sleeve.
• When protection sleeve core tube is longer than the length of outer sheath, cut off excess
sleeve to avoid micro bend after heating.
Stripping and Cleaning Fiber
Use the supplied ber stripping tool to strip the outer coating 30 to 40 mm (1.25 to 1.5 in) from its tip. Thoroughly clean the ber
with alcohol-soaked (99% or greater) gauze or lint-free tissue.

FSP200
Tempo Communications Inc. 1390 Aspen Way • Vista, CA 92081 USA • 800-642-2155
14
Fiber Cleaving
Do not let the ber end-face touch anything. Place the ber into the universal adapter, and insert the adapter into the FCL200.
Follow the instructions for the FCL200 to cleave the ber.
Loading Fiber into Splicer
1. Open the wind protector and install the ber adapters into the splicer, making sure the ber is positioned into the
center of the V-grooves.
2. Close the wind protector.
Splicing Procedure
To ensure a good splice, the optical ber is observed with the image processing system equipped in the FSP200. However, in
some cases the image processing system cannot detect a faulty splice. Visual inspection with the monitor is often necessary
for better splicing yield. Observe the following standard operating procedure:
• After bers are loaded into the splicer, press and the bers will move toward each other. The ber motion stops and the
cleaning arc is performed. The cleave angle and end-face quality are checked. If the measured cleave angle is greater
than its set threshold or ber chipping is detected, the beeper sounds and an error message warns the operator. The
splicing procedure pauses. If no error message is displayed, the below stated end-face conditions are used for visual
inspection. If observed, remove the ber from the splicer and repeat ber preparation. These ber cleave defects may cause
a faulty splice.
Chip Lip Incline
• After ber inspection, the bers are aligned core-to-core or cladding-to-cladding. Cladding axis offset and core axis offset
measurements can be displayed.
• After completion of ber alignment, an arc discharge is performed to splice the bers.
• Estimated splice loss is displayed upon completion of splicing. Splice loss is affected by factors stated in Section 5. These
factors are taken into account to calculate, or estimate, splice loss. The calculation is based on dimensional parameters,
such as MFD, cleave quality, and fusion splice shape after the splice. If either the cleave angle measured or the estimated
splice loss exceeds its set threshold, an error message is displayed. If the spliced ber is detected as abnormal, such as
“Fat”, “Thin” or “Bubble”, an error message is displayed. If no error message is displayed but the splice looks poor by visual
inspection through the monitor, it is strongly recommended to resplice.

FSP200
15
Tempo Communications Inc. 1390 Aspen Way • Vista, CA 92081 USA • 800-642-2155
Notes:
• Splice point sometimes looks a bit fatter than other parts. This is considered a normal splice and does not affect splice
loss.
• To change threshold for estimated splice loss or cleave angle, refer to “Splice Mode” in this manual for details.
• Splice loss may be improved in some cases by additional arc discharges. Splice loss estimate and splice check are
performed again. Splice loss may be worsened in some cases by additional arc discharges (re-arcs). Additional arc
discharge can be set to “disabled”, or limited to the number of additional arcs.
• Splicing result is automatically saved in splicer memory.
Arc Calibration
When a splicing session is rst started or if the splicing environment has changed, it is recommended that the technician
perform an arc calibration.
1. Place cleaved bers into the splicer.
2. Press and navigate to the “Maintenance” menu. Select “Arc Calibration.”
3. Follow the on-screen prompts.
Note: It might be necessary to repeat until “the arc adjust OK” prompt is achieved.
Heating Protection Sleeve
1. Transfer the ber with protection sleeve from the centering device to the tube heater.
2. Close the tube heater lid.
Notes:
• Make sure the splice point is located at the center of the protection sleeve.
• Make sure the strength member in the protection sleeve is placed downward.
• Make sure the ber is not distorted.
• The splice-on connector must be installed on the right-hand side of the splicer heater. Use heater prole #1 for the
SOC.
3. Press to start tube heating. The beeper sounds and the HEAT LED (red color) turns off when tube heating is
completed.

FSP200
Tempo Communications Inc. 1390 Aspen Way • Vista, CA 92081 USA • 800-642-2155
16
4. Open the tube heater lids and remove the protected ber from the tube heater. Apply some tension to the ber while
removing it from the tube heater.
5. Visually inspect the nished sleeve to verify that no bubbles or debris/dust is present in the sleeve.
Cooling Tray
Place the splice into the cooling tray on the back of the FSP200 splicer.
Splice-on Connectors
The FSP200 uses the Tempo Communications version of splice-on connectors. The FSP200 currently supports SC, LC, FC, and
ST versions (both PC and APC nish, where applicable).
Follow the instructions supplied with the splice-on connectors packaging.

FSP200
17
Tempo Communications Inc. 1390 Aspen Way • Vista, CA 92081 USA • 800-642-2155
Button Functions
Button Description
Turns the splicer ON/OFF
Menu key
Enter key
Return/Exit key
Left key
Right key/Help key
Up key/Bright key for LCD
Down key/Dark key for LCD
Start/Stop heating protection
Re-calibrates arc power
Resets the motor position
Starts splicing work
Switches between X, Y and X/Y views
Appendixes
Refer to the following appendixes at the end of this manual for additional operating information:
• Appendix A—FSP200 Fusion Splicer Cleaning
• Appendix B—Practice Splicing
• Appendix C—Tempo Communications Splice-on Connectors

FSP200
Tempo Communications Inc. 1390 Aspen Way • Vista, CA 92081 USA • 800-642-2155
18
Section 3. Menu Operation
Press to enter the splicer menu. There are six main menus:
1. Splice Mode Menu (S–Mode)
2. Heater Mode Menu (H–Mode)
3. Maintenance
4. Splice Set
5. Data Save
6. Set
Explanation of Splice Modes
Mode No. Splice Mode Description
1 AUTO
For splicing in most cases; the splicer will automatically adjust splice parameters according to
ber type.
Automatic arc calibration works in this splice mode.
2 AUTO SM
For splicing standard single-mode ber (ITU-T G652).
The MFD is 9 to 10 µm at wavelength of 1310 nm.
Automatic arc calibration works in this splice mode.
3 AUTO DS
For splicing dispersion-shifted ber (ITU-T G653).
The MFD is 7 to 9 µm at wavelength of 1550 nm.
Automatic arc calibration works in this splice mode.
4 AUTO NZ
For splicing non-zero dispersion-shifted ber (ITU-T G655).
The MFD is 9 to 10 µm at wavelength of 1550 nm.
Automatic arc calibration works in this splice mode.
5 AUTO MM1 For splicing multi-mode ber (ITU-T G651). Core diameter: 50.0 to 62.5 µm.
Automatic arc calibration works in this splice mode.

FSP200
19
Tempo Communications Inc. 1390 Aspen Way • Vista, CA 92081 USA • 800-642-2155
6 SM
For splicing standard single-mode ber (ITU-T G652).
The MFD is 9 to 10 µm at wavelength of 1310 nm.
User can edit all parameters of this splice mode such as prefuse power, prefuse time, arc
power, arc time, align, proof test, etc.
The manual splicing operation is provided. Automatic arc calibration does not work in this
splice mode.
7 DS
For splicing dispersion-shifted ber (ITU-T G653).
The MFD is 7 to 9 µm at wavelength near 1550 nm.
User can edit all parameters of this splice mode such as prefuse power, prefuse time, arc
power, arc time, align, proof test, etc.
The manual splicing operation is provided. Automatic arc calibration does not work in this
splice mode.
8 NZ
For splicing non-zero dispersion-shifted ber (ITU-T G655).
The MFD is 9 to 10µm at wavelength of 1550 nm.
User can edit all parameters of this splice mode such as prefuse power, prefuse time, arc
power, arc time, align, proof test, etc.
The manual splicing operation is provided. Automatic arc calibration does not work in this
splice mode.
9 MM1
For splicing multi-mode ber (ITU-T G651). Core diameter: 50.0 to 62.5 µm.
User can edit all parameters of this splice mode such as prefuse power, prefuse time, arc
power, arc time, align, proof test, etc.
The manual splicing operation is provided. Automatic arc calibration does not work in this
mode.
10 AT1(SM)
User can set the attenuation value in the range of 0.1 to 15 dB.
Set the desired splice loss. If after the splice is completed the desired loss is not achieved,
the user can adjust the splicing coecient. Increasing the coecient will increase the desired
loss; decreasing the coecient will reduce the splice loss.
11 SM FAST
For splicing standard single-mode ber (ITU-T G652).
The MFD is 9 to 10 µm at wavelength of 1310 nm.
This mode process does not analyze ber geometry.
12 SM G657
For slicing standard Bend Insensitive single-mode ber (ITU-T G657).
The MFD is 9 to 10 µm at wavelength of 1310 nm.
User can edit allthe parameters of this splice mode such as prefuse power, prefuse time, arc
power, arc time, align, proof test, etc.
The manual splicing operation is provided. Automatic arc calibration does not work in this
splice mode.
13~60 BLANK
(other modes) User can assign these as their own custom splicing proles.
Splice Mode Menu (S–Mode)
Explanation of Splice Modes (cont’d)

FSP200
Tempo Communications Inc. 1390 Aspen Way • Vista, CA 92081 USA • 800-642-2155
20
(1) Select Splice Mode
Select “S–Mode” to access the available splicing modes. Use the arrow keys to highlight the desired splicing mode. Then press
OK to conrm.
Select an appropriate splice mode for the type of ber to be spliced, and use the arrow keys to select the splice mode. Then
press OK to conrm.
Note: “1 AUTO SM/NZ/DS/MM” mode is recommended for splicing in most cases. In this mode, the splicer automatically
adjusts splice parameters according to the ber type.
(2) Edit Splice Mode
Splicing parameters in each splice mode can be modied.
In “Select Splice Mode” menu, press u to enter “Edit Splice Mode” and modify the splice mode .
Use the arrow keys to select the parameter to be modied, and then press OK to enter the parameter setting.
Use the arrow keys to modify the parameter, and then press OK to conrm.