Tempo Fitness 612T User manual

622T
TREADMILL OWNER’S MANUAL
MANUEL DU PROPRIÉTAIRE DU TAPIS ROULANT
MANUAL DEL PROPIETARIO DE LA CAMINADORA
Read the TREADMILL GUIDE before using this OWNER’S MANUAL.
Lire le GUIDE DU TAPIS ROULANT avant de se servir du présent MANUEL DU PROPRIÉTAIRE.
Lea la GUÍA DE LA CAMINADORA antes de usar este MANUAL DEL PROPIETARIO.
612T
TEM_12_612T_622T_OM_rev1_1.indd 1 2/28/12 8:32 AM

23
3 ENGLISH
32 FRANÇAIS
62 ESPAÑOL IMPORTANT PRECAUTIONS
SAVE THESE INSTRUCTIONS
When using an electrical product, basic precautions should always be followed, including the following: Read all instructions
before using this treadmill. It is the responsibility of the owner to ensure that all users of this treadmill are adequately informed of
all warnings and precautions. If you have any questions after reading this guide, contact Customer Tech Support at the number
listed on the back panel of the OWNER’S MANUAL.
This treadmill is intended for in-home use only. Do not use this treadmill in any commercial, rental, school or institutional setting.
Failure to comply will void the warranty.
TEM_12_612T_622T_OM_rev1_1.indd 2-3 2/28/12 8:32 AM

4 5
TO REDUCE THE RISK OF BURNS, FIRE, ELECTRICAL SHOCK OR INJURY TO PERSONS:
• At NO time should pets or children under the age of 13 be closer to the treadmill than 10 feet.
• At NO time should children under the age of 13 use the treadmill.
• Children over the age of 13 or disabled persons should not use the treadmill without adult supervision.
• Use the treadmill only for its intended use as described in the treadmill guide and owner’s manual.
• Do not use other attachments that are not recommended by the manufacturer. Attachments may cause injury.
• Never operate the treadmill if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or
immersed in water. Return the treadmill to a service center for examination and repair.
• Keep power cord away from heated surfaces. Do not carry this unit by its supply cord or use the cord as a handle.
• Never operate the treadmill with the air opening blocked. Keep the air opening clean, free of lint, hair, and the like.
• To prevent electrical shock, never drop or insert any object into any opening.
• Do not operate where aerosol (spray) products are being used or when oxygen is being administered.
• To disconnect, turn all controls to the off position, then remove plug from outlet.
• Do not use treadmill in any location that is not temperature controlled, such as but not limited to garages, porches, pool rooms,
bathrooms, car ports or outdoors. Failure to comply may void the warranty.
• This treadmill is intended for in-home use only. Do not use this treadmill in any commercial, rental, school or institutional setting.
Failure to comply will void the warranty.
• Do not remove the console covers unless instructed by Customer Tech Support. Service should only be done by an authorized
service technician
It is essential that your treadmill is used only indoors, in a climate controlled room. If your treadmill has been exposed to colder
temperatures or high moisture climates, it is strongly recommended that the treadmill is warmed up to room temperature before
first time use. Failure to do so may cause premature electronic failure.
TO REDUCE THE RISK OF BURNS, FIRE, ELECTRICAL SHOCK OR INJURY TO PERSONS:
• Never use the treadmill before securing the safety tether clip to your clothing.
• If you experience any kind of pain, including but not limited to chest pains, nausea, dizziness, or shortness of breath, stop
exercising immediately and consult your physician before continuing.
• When exercising, always maintain a comfortable pace.
• Do not wear clothes that might catch on any part of the treadmill.
• Always wear athletic shoes while using this equipment.
• Do not jump on the treadmill.
• At no time should more than one person be on treadmill while in operation.
• This treadmill should not be used by persons weighing more than specified in the OWNER’S MANUAL WARRANTY SECTION.
Failure to comply will void the warranty.
• When lowering the treadmill deck, wait until rear feet are firmly on the floor before stepping on the deck.
• Disconnect all power before servicing or moving the equipment. To clean, wipe surfaces down with soap and slightly damp cloth
only; never use solvents. (See MAINTENANCE)
• The treadmill should never be left unattended when plugged in. Unplug from outlet when not in use, and before putting on or
taking off parts.
• Do not operate under blanket or pillow. Excessive heating can occur and cause fire, electric shock, or injury to persons.
• Connect this exercise product to a properly grounded outlet only.
WARNING
TO REDUCE THE RISK OF ELECTRICAL SHOCK:
Always unplug the treadmill from the electrical outlet immediately after using, before cleaning, performing maintenance and putting on or
taking off parts.
DANGER WARNING
TEM_12_612T_622T_OM_rev1_1.indd 4-5 2/28/12 8:32 AM

67
ASSEMBLY
There are several areas during the assembly process that special attention must be paid. It is very important to follow the assembly
instructions correctly and to make sure all parts are firmly tightened. If the assembly instructions are not followed correctly, the
treadmill could have parts that are not tightened and will seem loose and may cause irritating noises. To prevent damage to the
treadmill, the assembly instructions must be reviewed and corrective actions should be taken.
Before proceeding, find your treadmill’s serial number located on a white barcode sticker
near the on/off power switch and power cord and enter it in the space provided below.
ENTER YOUR SERIAL NUMBER AND MODEL NAME IN THE BOXES BELOW:
» Refer to the SERIAL NUMBER and MODEL NAME when calling for service.
SERIAL NUMBER:
TM
MODEL NAME: TEMPO TREADMILL
WARNING
SERIAL NUMBER LOCATION
GROUNDING INSTRUCTIONS
This product must be grounded. If a treadmill should malfunction or breakdown, grounding provides a path of least resistance
for electrical current to reduce the risk of electrical shock. This product is equipped with a cord having an equipment-grounding
conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in
accordance with local codes and ordinances.
Connect this exercise product to a properly grounded outlet only.
Never operate product with a damaged cord or plug even if it is working
properly. Never operate any product if it appears damaged, or has been
immersed in water. Contact Customer Tech Support for replacement or repair.
3-POLE
GROUNDED
OUTLET
GROUNDING PIN
WARNING
DANGER
Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified
electrician or serviceman if you are in doubt as to whether the product is properly grounded. Do not modify the plug provided
with the product. If it will not fit the outlet, have a proper outlet installed by a qualified electrician.
This product is for use on a nominal 110-120 Volt circuit and has a grounding plug that looks like the plug in the illustration. Make
sure that the product is connected to an outlet having the same configuration as the plug. No adapter should be used with this
product.
This product must be used on a dedicated circuit. To determine if you are on a dedicated circuit, shut off the power to that circuit
and observe if any other devices lose power. If so, move devices to a different circuit. Note: There are usually multiple outlets on one
circuit. This treadmill should be used with a minimum 15-amp circuit.
TEM_12_612T_622T_OM_rev1_1.indd 6-7 2/28/12 8:32 AM

8 9
ON/OFF SWITCH
CIRCUIT BREAKER
TRANSPORT WHEEL
POWER COR D
RE ADING RACK
TOUCH PAD PANEL WATE R BOTTLE HOLD ER
CONSOLE
SAFE T Y KEY PLACEME NT
RUNNING BELT / RUNNING DECK
SIDE R AIL
ROLLER END CAP
CONSOLE MAS T
HANDLEBARS
RE AR ROLLER
TENSION/ALIGN MENT BOLTS
MOTOR COVER
MANUAL INCLINE MECHANISM
DECK LOC K PIN
CAUTION ATTENTION PRECAUCIÓN
KEEP HANDS AND FEET
AWAY FROM THIS AREA.
GARDER LES MAINS ET LES
PIEDS LOIN DE CETTE REGION.
MANTENGA LAS MANOS Y LOS
PIES LEJOS DE ESTA ÁREA.
CAUTION ATTENTION PRECAUCIÓN
HOLD ONTO DECK WHEN
LATCH IS RELEASED.
TENIR LA PLATE-FORME LORSQUE LA
GOUPILLE DE VERROUILLAGE EST RETIRÉE.
SUJETE LA PLATAFORMA
CUANDO SUELTE EL SUJETADOR.
ATTACHER LA PINCE DE LA CLÉ DE SÉCURITÉ AUX VÊTEMENTS AVANT DE COMMENCER.
POUR ÉVITER TOUTES BLESSURES, SE TENIR SUR LES RIDELLES AVANT DE DÉMARRER
LE TAPIS ROULANT. AVANT USAGE, LIRE LE GUIDE D’UTILISATEUR. NE PAS LAISSER CET
ÉQUIPEMENT À LA PORTÉE DES ENFANTS. ENLEVER LA CLÉ DE SÉCURITÉ LORSQUE LE
TAPIS ROULANT N’EST PAS UTILISÉ ET LA RANGER HORS DE LA PORTÉE DES ENFANTS.
CONSULTER UN MÉDECIN AVANT D’UTILISER CET ÉQUIPEMENT. ARRÊTER D’UTILISER
L’APPAREIL EN CAS DE DOULEUR, D’ÉVANOUISSEMENT, DE VERTIGE OU
D’ESSOUFFLEMENT. GARDER LE CORPS ET LES VÊTEMENTS LIBRE DES PIÈCES EN
MOUVEMENT. POUR USAGE DOMESTIQUE UNIQUEMENT.
ATTENTIONRISQUE DE BLESSURES:
SUJETE LA LLAVE DE SEGURIDAD A SU ROPA ANTES DE COMENZAR. PARA
EVITAR ACCIDENTES PARESE EN LO RIELES ANTES DE COMENZAR. LEA
CUIDADOSAMENTE EL MANUAL DE USUARIO Y CONSULTE A SU MEDICO
ANTES DE COMENZAR. MANTENGA EL PRODUCTO FUERA DEL ALCANZE DE
LOS MENORES. QUITE LA LLAVE DE SEGURIDAD CUANDO NO ESTE EN USO.
CONSULTAR CON UN MEDICO ANTES DE USAR ESTE EQUIPO. SI SIENTE
ALGUN DOLOR O FATIGA PARE DE INMEDIATO. MANTENER SU CUERPO Y
VESTIMENTA LEJOS DE TODAS LAS PARTES EN MOVIMIENTO DE LA
MAQUINA. ESTE EQUIPO ES SÓLO PARA EL USO DEL CONSUMIDOR.
PRECAUCIÓNEL RIESGO DE UNA
LESION A PERSONAS:
ON/OFF SWITCH
CIRCUIT BREAKER
TRANSPORT WHEEL
POWER COR D
RE ADING RACK
TOUCH PAD PANEL WATE R BOTTLE HOLD ER
CONSOLE
SAFE T Y KEY PLACEME NT
GRIP PULS E HANDRAILS
RUNNING BELT / RUNNING DECK
SIDE R AIL
ROLLER END CAP
CONSOLE MAS T
HANDLEBARS
RE AR ROLLER
TENSION/ALIGN MENT BOLTS
MOTOR COVER
DECK LOC K PIN
FRAME E XTENSION TUBE
CAUTION ATTENTION PRECAUCIÓN
KEEP HANDS AND FEET
AWAY FROM THIS AREA.
GARDER LES MAINS ET LES
PIEDS LOIN DE CETTE REGION.
MANTENGA LAS MANOS Y LOS
PIES LEJOS DE ESTA ÁREA.
CAUTION ATTENTION PRECAUCIÓN
HOLD ONTO DECK WHEN
LATCH IS RELEASED.
TENIR LA PLATE-FORME LORSQUE LA
GOUPILLE DE VERROUILLAGE EST RETIRÉE.
SUJETE LA PLATAFORMA
CUANDO SUELTE EL SUJETADOR.
ATTACHER LA PINCE DE LA CLÉ DE SÉCURITÉ AUX VÊTEMENTS AVANT DE COMMENCER.
POUR ÉVITER TOUTES BLESSURES, SE TENIR SUR LES RIDELLES AVANT DE DÉMARRER
LE TAPIS ROULANT. AVANT USAGE, LIRE LE GUIDE D’UTILISATEUR. NE PAS LAISSER CET
ÉQUIPEMENT À LA PORTÉE DES ENFANTS. ENLEVER LA CLÉ DE SÉCURITÉ LORSQUE LE
TAPIS ROULANT N’EST PAS UTILISÉ ET LA RANGER HORS DE LA PORTÉE DES ENFANTS.
CONSULTER UN MÉDECIN AVANT D’UTILISER CET ÉQUIPEMENT. ARRÊTER D’UTILISER
L’APPAREIL EN CAS DE DOULEUR, D’ÉVANOUISSEMENT, DE VERTIGE OU
D’ESSOUFFLEMENT. GARDER LE CORPS ET LES VÊTEMENTS LIBRE DES PIÈCES EN
MOUVEMENT. POUR USAGE DOMESTIQUE UNIQUEMENT.
ATTENTIONRISQUE DE BLESSURES:
SUJETE LA LLAVE DE SEGURIDAD A SU ROPA ANTES DE COMENZAR. PARA
EVITAR ACCIDENTES PARESE EN LO RIELES ANTES DE COMENZAR. LEA
CUIDADOSAMENTE EL MANUAL DE USUARIO Y CONSULTE A SU MEDICO
ANTES DE COMENZAR. MANTENGA EL PRODUCTO FUERA DEL ALCANZE DE
LOS MENORES. QUITE LA LLAVE DE SEGURIDAD CUANDO NO ESTE EN USO.
CONSULTAR CON UN MEDICO ANTES DE USAR ESTE EQUIPO. SI SIENTE
ALGUN DOLOR O FATIGA PARE DE INMEDIATO. MANTENER SU CUERPO Y
VESTIMENTA LEJOS DE TODAS LAS PARTES EN MOVIMIENTO DE LA
MAQUINA. ESTE EQUIPO ES SÓLO PARA EL USO DEL CONSUMIDOR.
PRECAUCIÓNEL RIESGO DE UNA
LESION A PERSONAS:
ATTACH SAFETY KEY CLIP TO CLOTHING BEFORE STARTING. TO AVOID
INJURY, STAND ON THE SIDE RAILS BEFORE STARTING TREADMILL. READ
AND FOLLOW ALL INSTRUCTIONS BEFORE OPERATING. KEEP CHILDREN
AWAY FROM THIS EQUIPMENT. REMOVE SAFETY KEY WHEN NOT IN USE
AND STORE OUT OF REACH OF CHILDREN. CONSULT A PHYSICIAN
BEFORE USING THIS EQUIPMENT. STOP EXERCISING IF YOU FEEL PAIN,
FAINT, DIZZY OR SHORT OF BREATH. KEEP BODY AND CLOTHING FREE
AND CLEAR OF ALL MOVING PARTS. FOR CONSUMER USE ONLY.
CAUTIONRISK OF INJURIES TO PERSONS:
612T622T
TEM_12_612T_622T_OM_rev1_1.indd 8-9 2/28/12 8:32 AM

10 11
TOOLS INCLUDED:
F4 mm Allen Wrench
F5 mm L-Wrench/Screwdriver
F6 mm T-Wrench
PARTS INCLUDED:
F1 Safety Key
F1 Console Assembly
F2 Console Masts
F2 End Caps
F612T: 2 Handlebars
F612T: 4 Hardware Bags
F622T: 5 Hardware Bags
F622T: 2 Frame Extension Tubes
F1 Bottle of Silicone Lubricant
(for 2 applications)
FFrench Overlays
If you have questions or if
there are any missing parts,
contact Customer Tech
Support. Contact information
is located on the back panel
of this manual.
DO NOT ATTEMPT TO LIFT THE TREADMILL! Do not move or lift treadmill
from packaging until specified to do so in the assembly instructions. You may
remove the plastic wrap from console masts.
WARNING
UNPACKING
Place the treadmill carton on a level flat surface. It is recommended that you place a
protective covering on your floor. Take CAUTION when handling and transporting this
unit. Never open box when it is on its side. Once the banding straps have been removed,
do not lift or transport this unit unless it is fully assembled and in the upright folded
position, with the lock latch secure. Unpack the unit where it will be used. Never grab
hold of any portion of the incline frame and attempt to lift or move the treadmill.
FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN INJURY!
WARNING
NEED HELP?
NOTE: During each assembly step, ensure that ALL nuts and bolts are in place and
partially threaded in before completely tightening any ONE bolt.
NOTE: A light application of grease may aid in the installation of hardware. Any grease,
such as lithium bike grease is recommended.
PRE ASSEMBLY ASSEMBLY STEP 1
A Cut the yellow banding straps and lift the
running deck upward and remove all
contents from underneath the running deck.
B Open hardware bag 1.
C With the running deck lowered, attach
the left console mast to the base
frame using 2 bolts (a), 2 spring
washers (b) and 2 flat washers (c)
from the side and 2 bolts (a), 2 spring
washers (b) and 2 arc washers (d)
from the rear.
BOLT (A)
20 mm
Qty: 4
SPRING WASHER (B)
8 mm
Qty: 4
FLAT WASHER (C)
8 mm
Qty: 2
ARC WASHER (D)
8 mm
Qty: 2
HARDWARE BAG 1 CONTENTS :
BOLTS (A)
SPRING WASHERS (B)
612T
LEFT CONSOLE MAST
ARC WASHERS (D)
FLAT WASHERS (C)
BASE FRAME
622T PLUS
LEFT CONSOLE MAST
ALL
MODELS
ALL
MODELS
TEM_12_612T_622T_OM_rev1_1.indd 10-11 2/28/12 8:32 AM

12 13
ASSEMBLY STEP 2
BOLT (A)
20 mm
Qty: 4
SPRING WASHER (B)
8 mm
Qty: 4
FLAT WASHER (C)
8 mm
Qty: 2
ARC WASHER (D)
8 mm
Qty: 2
HARDWARE BAG 2 CONTENTS :
BOLTS (A)
SPRING WASHERS (B)
612T
RIGHT CONSOLE MAST
ARC WASHERS (D)
CONSOLE CABLE FLAT WASHERS (C)
BASE FRAME
LEAD WIRE
622T
RIGHT CONSOLE MAST
A Open hardware bag 2.
B Pull lead wire through right console
mast. After pulling the lead wire through the
mast, the top of the console cable should
be located at the top of the mast. Detach and
discard the lead wire.
C With the running deck lowered, attach
the right console mast to the base
frame using 2 bolts (a), 2 spring
washers (b) and 2 flat washers (c)
from the side and 2 bolts (a), 2 spring
washers (b) and 2 arc washers (d)
from the rear.
NOTE: Be careful not to pinch any wires
while assembling the right console mast.
622T
ONLY
622T ASSEMBLY STEP 3
* This step is for 622T model only.
A Open hardware bag 3.
B Slide console onto console masts and
attach using 4 arc washers (e), 4 spring
washers (f) and 4 bolts (g).
C Connect the console cable and carefully tuck
wires in console mast to avoid damage.
D Attach console cable cover to secure
console cable.
BOLT (G)
45 mm
Qty: 4
SPRING WASHER (F)
6 mm
Qty: 4
ARC WASHER (E)
6 mm
Qty: 4
HARDWARE BAG 3 CONTENTS :
CONSOLE
BOLTS (G)
SPRING WASHERS (F)
ARC WASHERS (E)
CONSOLE MAST
CONSOLE
CABLE
CONSOLE
CABLE COVER
NOTE: Be careful not to pinch any wires
while assembling the console.
622T ONLY
ALL
MODELS
TEM_12_612T_622T_OM_rev1_1.indd 12-13 2/28/12 8:32 AM

14 15
612T ASSEMBLY STEP 3
* This step is for 612T model only.
A Open hardware bag 3.
B Slide each handlebar into the console
and attach using 2 bolts (e), 2 spring
washers (f) and 2 arc washers (g). Do
not completely tighten bolts until step D.
C Gently place the console on top of the
console masts. Attach the left side first
using 2 bolts (h), 2 spring washers (b)
and 2 arc washers (d).
D Attach the right side of the console using
2 bolts (h), 2 spring washers (b) and 2
arc washers (d). Completely tighten all bolts
from steps B–D.
BOLT (E)
15 mm
Qty: 4
BOLT (H)
55 mm
Qty: 4
SPRING
WASHER (F)
6 mm
Qty: 2
ARC
WASHER (G)
6 mm
Qty: 2
SPRING WASHER (B)
8 mm
Qty: 4
ARC
WASHER (D)
8 mm
Qty: 4
HARDWARE BAG 3 CONTENTS :
ASSEMBLE
LEFT SIDE
FIRST
CONSOLE
CABLE
BOLTS (E)
SPRING WASHERS (F)
ARC WASHERS (G)
HANDLEBAR
CONSOLE
BOLTS (H)
SPRING WASHERS (B)
ARC WASHERS (D)
CONSOLE MAST
NOTE: be careful not to pinch any
wires while attaching the console.
612T ONLY
CONSOLE
CABLE CONSOLE CABLE
COVER
PLASTIC CLIPS
BOLTS (E)
CONSOLE MAST
HANDLEBAR
CONSOLE
E Remove the console cable cover.
F Connect the console cable and secure the
cable in the 2 plastic clips. Carefully tuck
excess cable in the console mast to avoid
damage.
G Attach the console cable cover to secure
the console cable.
H Secure the handlebars to the console
masts by inserting 2 bolts (e) from below the
console.
612T ONLY
612T ASSEMBLY STEP 3 CONTINUED
612T
ONLY
612T
ONLY
TEM_12_612T_622T_OM_rev1_1.indd 14-15 2/28/12 8:32 AM

16 17
ASSEMBLY STEP 4
A Open hardware bag 4.
NOTE: lock latch must be securely engaged
before proceeding with assembly. (See folding
instructions in TREADMILL GUIDE.)
B Attach the right end cap using 2 screws
(h). Repeat on the other side.
C Connect power cord to a power outlet. The
ON/OFF switch is located next to the power
cord. Flip this switch to the ‘ON’ position. You
will hear a beep and the console will turn on.
D Before the first use, lubricate the treadmill
deck by following the instructions in the
MAINTENANCE section in the TREADMILL
GUIDE.
SCREW (H)
12 mm
Qty: 4
HARDWARE BAG 4 CONTENTS :
END CAPS
SCREWS (H)
MAIN FRAME
612T
YOU ARE FINISHED!
622T
622T ASSEMBLY STEP 5
* This step is for 622T model only.
A Open hardware bag 5.
B Slide the left frame eXtension tube onto
the base frame. Bolt in place using 2 bolts (i)
on the side.
C Repeat on the other side.
D NOTE: the treadmill must be lifted up slightly
while sliding the frame extension tube into
position.
BOLT (I)
15mm
Qty: 4
HARDWARE BAG 5 CONTENTS :
FRAME EXTENSION TUBE BOLTS (I)
622T ONLY
622T
YOU ARE FINISHED!
622T
ONLY
ALL
MODELS
TEM_12_612T_622T_OM_rev1_1.indd 16-17 2/28/12 8:32 AM

18 19
TREADMILL OPERATION
This section explains how to use your treadmill’s console and programming. The BASIC OPERATION section in the
TREADMILL GUIDE has instructions for the following:
• LOCATION OF THE TREADMILL
• USING THE SAFETY KEY
• FOLDING THE TREADMILL
• MOVING THE TREADMILL
• LEVELING THE TREADMILL
• TENSIONING THE RUNNING BELT
• CENTERING THE RUNNING BELT
• USING THE HEART RATE FUNCTION
TEM_12_612T_622T_OM_rev1_1.indd 18-19 2/28/12 8:32 AM