TEMPUR FORM User manual

TEMPUR ARC™ Bed range
ASSEMBLY GUIDE

2 3
Contents
TEMPUR ARC™ Outer frames assembly guide 4
Product exceptions: Luxury headboard 8
TEMPUR ARC™ Inner frame(s) assembly guide
TEMPUR ARC™ Static slatted inner frame(s) assembly guide 14
TEMPUR ARC™ Static disc inner frame(s) assembly guide 23
TEMPUR ARC™ Adjustable slatted inner frame(s) assembly guide 32
TEMPUR ARC™ Adjustable disc inner frame(s) assembly guide 48

3
Welcome to TEMPUR®
Thank you for choosing a TEMPUR®product.

4 5
TEMPUR ARC™ Bed range
Outer frames assembly guide

5
Welcome!
Here are TEMPUR ARC™ beds, outer frames with headboards. Regardless of your choice of
headboard, bed size or bed type, the assembly of the outer frames is the same in all cases.
TEMPUR®FORM
TEMPUR®VERTICAL
TEMPUR®SENSORY
TEMPUR®QUILTED
TEMPUR®VECTRA
TEMPUR®LUXURY

6 7
CAUTION
The assembly instructions must be followed closely to install the bed system
successfully, safely, and to minimize the risk of personal injuries and damage
to the product.
Assemble the product with a minimum of two persons.
Open the packaging carefully, so as not to damage the product and its parts.
Dispose of the packaging safely and as sustainably as possible in your local area.

7
Component list
Check all components. All the means and tools required for product assembly come with
the product:
4 x cones; 4 x leg details; 4 x felt pads
1 x headboard 2 x side panels
1 x foot-end panel

8 9
Products exceptions
TEMPUR®LUXURY headboard extra component
In case you have a TEMPUR®LUXURY headboard, there is an additional component,
a headboard extra panel.
TEMPUR® LUXURY will be standing on the oor. The additional panel is attached on
the headboard in the factory. It is moving on rails up and down into the right position
according to the legs height.

9
Assembly steps
1. Connecting cones with legs
Connect cones with leg details. Screw legs into
cones. Make sure that these are xed rmly.
2. Follow icons on the corner
connectors
Follow the head and feet graphic icons
on the corner connectors. You need
to connect the corners with matching
icons on them, feet with feet and head
with head. Follow the direction of the
icons; they need to be upright as shown
in the drawing.

10 11
3. Organizing the bed parts
Lay all outer frame parts on the oor, connectors facing upside.

11
4. Connecting one side panel with headboard
Place one side panel into the headboard corner connector. Fix the
panel by placing one leg into the corner connector. Push the leg,
no need to twist the legs. When the bed frame will be lifted into
its upright position afterwards, these will be xed in rmly.
5. Connecting second side panel with headboard
Connect second side panel with the headboard
corner connector and x it with another leg.
CAUTION
Be careful not to trap your ngers between the
corner ngers joint nor between the leg cone
and the corner connector while attaching the leg.

12 13
One person is standing by one foot-
end corner and the other person is
standing by the opposite corner, shown
with arrows on the drawing. Add the
foot-end by connecting both foot-end
panel corners into the side panel corner
connectors. To do it smoothly, do it in
one rhythm and simultaneously.
One person is standing on one side of the
bed frame by the head-end and another
one the opposite side. Hold with one hand
the headboard and with other hand the side
panel, follow the arrows on the drawing for
hand positions. Turn the bed to its horizontal
position. If there is little space in the room,
you can lift the head-end while turning the
frame around, in this way it saves space.
6. Turning bed to horizontal position
7. Adding foot-end panel

13
8. Fixing the foot-end with legs
One person is by one foot-end corner and another one in the opposite corner, shown
with arrows on the drawing. Fix the foot-end panel by placing legs in each corner
connector and push them. No need to twist, the weight of the construction of the bed
will x the legs to the end position. To make sure that the legs are xed rmly, you
can lift the bed from the front and back corners slightly, not more than up to 10 cm,
and let it fall to the oor under its weight.
CAUTION
While installing, keep your feet a safe
distance away from the bed frame.
CAUTION
Make sure that the foot cone is
completely inside the corner connector.

14 15
TEMPUR ARC™ Static Slatted
Static slatted inner frame(s) assembly guide

15
CAUTION
The assembly instructions must be followed closely to install the bed system
successfully, safely, and to minimize the risk of personal injuries and damage
to the product.
Assemble the product with a minimum of two persons.
Open the packaging carefully, so as not to damage the product and its parts.
Dispose of the packaging safely and as sustainably as possible in your local area.

16 17
Component(s)
You have 1 inner frame if your bed size is 90x200; 100x200; 140x200 cm.
You have 2 inner frames in case your bed size is 150x200; 160x200; 180x200 cm.
Follow the direction of the frame, you have thin stripes at the head-end on the slats.
Head-end
Foot-end

17
Removing transport holders
Remove 4 pieces of white plastic holders at the head- and foot-end.

18 19
CAUTION
Lift and carry the frame with
two people by holding it from
the bottom support frames.
WARNING
While mounting the frame(s),
be careful your ngers are
not trapped between the
outer and inner frame.
CAUTION
Be aware not to carry the frame by
holding it only from the middle of the
slats, these may come off or be damaged.

19
1
2 2
1
Lift the frame horizontally with two persons, both holding the frame from the longer
opposite sides, from the bottom support frame. Lift the frame head-end onto the
headboard metal support angle. As the frame head-end is placed, it is not so heavy
anymore and you can place your hands on the top of the frame now, onto the slats.
Drop the other frame end slowly and carefully onto the foot-end.
Single static slatted inner frame placement

20 21
1
2 2
1
Take one frame with two people and turn it sideways. One person lifts the
frame from the head-end and the other one from the foot-end. Hold the frame
from its longer side support frame. Place the frame by sideways (inner side
facing downwards) inside the outer frame. Install the frame head-end onto the
headboard metal angle rst and then the foot-end onto the bed foot-end. Raise
your hands on the top of the frame, hold from the slats. Drop the frame slowly
and carefully sideways into a horizontal position.
Double static slatted inner frames placement