Argos 600/0774 User manual

Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the customer helpline: 08456 400800
Dimensions
600/0774
600/0781
Gaslift Bar Table
Assembly Instructions - Please keep for future reference
Width - 53cm
Depth - 53cm
Height - 67~92.5cm

1
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Assemble this product on a
flat surface.
• Assemble all parts loosely
before tightening any bolts.
• Discard all extra fittings and
keep fittings out of reach of
children.
• We suggest you spend a short
time reading through this leaflet
and follow the simple step by
step assembly instructions.
• Do not discard any of the
packaging until you have
checked that you have all the
parts and the pack of fittings.
• Unit weight : 7.5kg.
• We recommend that this unit is
assembled by at least 2 people.
• Retain Assembly Instructions
for future reference.
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
Warnings
• This product should only be
used on firm, level ground.
• Make sure the base remain in
contact with the ground.
• Do not stand on the product.
Care and maintenance
• Please clean the table surface
using either damp (not wet)
cloth and a mild domestic soap
solution or by using an
appropriate polish.
• Do not use any abrasive
materials when cleaning.
• From time to time check that
there are no loose bolts on
this unit.

2
Components - Parts
Please check you have all the parts listed below
1Table top
(Ø53 x 1.8cm) 2Upper leg
(Ø5.6 x 16 x 39cm)
3Gaslift
(Ø5 x 61~85cm)
4Base
(Ø45 x 8.5cm)

3
Please check you have all the fittings listed below
Components - Fittings If you have damaged or missing components,
call the customer helpline: 08456 400800
Note: The quantities below are the correct amount to complete the assembly. In some cases more
fittings may be supplied than are required.
C
Washer x 4
AB
M6 x 16mm Bolt x 4 Spring washer x 4
Tools required
Crosshead
Screwdriver
Ruler - Use this ruler to help correctly identify the screws
105150 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155 160 165 170

4
Step 3
Attaching table top
Position the table top
as shown and insert the
gaslift into the upper
leg . Secure by press-
ing down the table top
firmly.
3
2
Place the base on a
flat protected surface.
Insert the gaslift into
hole of the base .
Gaslift operation
To adjust the table
higher, lift up the lever
under the table and
release at desired height.
To lower the table, lift up
the lever while pressing
down the table top.
33
3
4
Attaching gaslift
Important:
Remove plastic
tip cover on gaslift
before assem-
bling.
Attaching table top
Place the table top on
a flat protected surface.
Position the upper legs
on the table top as
shown. Align the holes
and fix together using
bolts & spring washers
& washers . Tighten
the bolts using screw-
driver.
2 1
CB
AC
B
C
B
C
B
C
B
A
AA
A
Assembly Instructions
Step 1
Step 2
If you need help or have damaged or missing parts, call the customer helpline: 08456 400800
1
1
1
2
2
2
4
4
Lever