Tennsco L&T Hinged Door Kit Instruction Manual

PK-1440119
ASSEMBLY INSTRUCTIONS & PARTS MANUAL
L&T Hinged Door Kit
RETAIN INSTRUCTIONS FOR FUTURE REFERENCE
GENERAL SAFETY INFORMATION
Some parts may have sharp edges. CARE must be taken when handling various pieces to avoid injury.
For safety, wear a pair of work gloves when assembling or performing any maintenance on products.
LIMITED WARRANTY
Tennsco warrants goods purchased hereunder to be free of defects in materials and workmanship for a period of one (1) year from the date of shipment, hereunder. This warranty shall not apply in
the event goods are damaged as a result of misuse, abuse, neglect, accident, improper application, modication or repair by persons not authorized by Seller, where goods are damaged during
shipment, or where the date stamps on the goods have been defaced, modied or removed. UNLESS CONSIDERED UNENFORCEABLE OR UNLAWFUL UNDER APPLICABLE LAW:
a. ALL IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO WARRANTIES OR MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY EXCLUDED:
b. BUYERS REMEDY, IF ANY, FOR ANY DEFECTIVE GOODS SHALL BE LIMITED TO A REFUND BY SELLER OR REPLACEMENT OF THE GOODS AT SELLER’S OPTION, AND SHALL IN NO
EVENT INCLUDE DAMAGES OF ANY KIND, WHETHER INCIDENTAL, CONSEQUENTIAL OR OTHERWISE.
NO GOODS ACCEPTED FOR RETURN WITHOUT PRIOR APPROVAL. Seller shall have the right to inspect any goods claimed to be defective at Buyers place of business or require Buyer to return the
goods to Seller for inspection on Seller’s premises. Transportation charges covering returned goods will be borne by Seller only if such goods are proven to be defective, are covered by this warranty
and are returned within the warranty period stated above.
Tennsco LLC. , Dickson, TN 37056-1888 • [phone]
Hinged Door Kit as purchased Hinged Door Kit on L&T unit
(purchased separately)

ASSEMBLY OF L&T HINGED DOOR KIT
Tools Needed:
Two people are recommended for assembly. Approximate assembly time: 20-30 minutes.
2. For standard installation, lift the door frame
assembly, tilting upper edge toward the unit
to enable the hooks to insert in the top of
the post. When the hooks are in place, lower the
door front against the front of the unit. Line
up door frame and cabinet frame.
1. The reference numbers used throughout
this sheet refer to the illustration on the
back cover. This is to help you to identify
the various parts as they are mentioned.
NOTE: 1” and 2” Door Frames are installed
the same way.
HOOKS

Handle/Locking System Installation
3. Secure the left side of the door frame to post by pressing
steel clips over edge of post and angles on door frame.
Install three clips: top, middle, and bottom. Tighten screws in
clips to securely fasten frame to shelving unit. Repeat this
procedure to secure the right side of the door frame.
4. Make sure the cabinet is level so the doors will operate
properly. You are now ready to install the locking handle
and lock bars to the door.
1. Place the locking handle (Ref. No. 4) on the right hand
door and push it until it snaps into place. Then turn the
handle to the open position. The latch should be facing
downward as shown.
2. With the handle still in
the open position, hook
the locking bars (Ref.
No. 3) to the locking
cam on the back of the
recessed handle.
4. Slide the nylon lock bar guide inserts
(Ref. No. 5) over the lock bar ends
and through the door slots. Push
down rmly until the guides snap
into place.



Outside view
Inside view
3. Slowly rotate the door handle
to the closed position so the
lock bars protrude from the
holes at the top and bottom
of the door (shown below).

REPLACEMENT PARTS




Locking Bar Guide
Nylon Insert
(Ref No. 5)
Locking Bar Set
(Ref No. 3)
Locking Recessed
Handle
with Keys
(Ref No. 4)
1 1” Depth Hinged Door Kit OR *LTHD-wwhhRH 1
2” Depth Hinged Door Kit *LTHD-wwhhRHD 1
2 Clip for L&T Hinged Door LTHD-CLIP 1
3 Locking Bar Set **LTHD-hhLB 1
4 Locking Recessed Handle w/Keys RH-1 1
5 Locking Bar Guide Insert (Nylon) 944GI 2
Hinged Door
& Frame Assembly
(Ref No. 1)
NOTE: Additional hardware may be included for replacement purposes.
REF.
NO.
*LTHD-wwhh, where “-wwhh” indicates the width and height of the unit. Example: an LTHD-4876RH fits on a 48”w x 76”h L&T unit.
Tennsco makes every effort to ensure that all units ship complete with all parts and arrive undamaged.
However, should your unit contain missing or damaged parts, please contact your purchase location.
PART NO. QTY.DESCRIPTION
**LTHD-hhLB, where “-hh” indicates the height of the unit. Example: an LTHD-76LB fits on a 76”h L&T Hinged Door.

Door Clip
(Ref No. 2)
49B144
NOTE: Image above shows a breakdown,
however the Locking Cam and Cam
Retainer come installed on the Recessed
Handle, and are not separate items.


Locking Cam
Cam Retainer