Tennsco Stackable Workbench Drawer Unit Instruction Manual

ASSEMBLY INSTRUCTIONS & PARTS MANUAL
PK-1420719
Stackable Workbench
Drawer Unit
RETAIN INSTRUCTIONS FOR FUTURE REFERENCE
Tennsco LLC. , Dickson, TN 37056-1888 • [phone]
GENERAL SAFETY INFORMATION
Some parts may have sharp edges. CARE must be taken when handling various pieces to avoid injury.
For safety, wear a pair of work gloves when assembling or performing any maintenance.
LIMITED WARRANTY
Tennsco warrants goods purchased hereunder to be free of defects in materials and workmanship for a period of one (1) year from the date of shipment, hereunder. This warranty shall not apply in
the event goods are damaged as a result of misuse, abuse, neglect, accident, improper application, modication or repair by persons not authorized by Seller, where goods are damaged during
shipment, or where the date stamps on the goods have been defaced, modied or removed. UNLESS CONSIDERED UNENFORCEABLE OR UNLAWFUL UNDER APPLICABLE LAW:
a. ALL IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO WARRANTIES OR MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY EXCLUDED:
b. BUYERS REMEDY, IF ANY, FOR ANY DEFECTIVE GOODS SHALL BE LIMITED TO A REFUND BY SELLER OR REPLACEMENT OF THE GOODS AT SELLER’S OPTION, AND SHALL IN NO
EVENT INCLUDE DAMAGES OF ANY KIND, WHETHER INCIDENTAL, CONSEQUENTIAL OR OTHERWISE.
NO GOODS ACCEPTED FOR RETURN WITHOUT PRIOR APPROVAL. Seller shall have the right to inspect any goods claimed to be defective at Buyers place of business or require Buyer to return the
goods to Seller for inspection on Seller’s premises. Transportation charges covering returned goods will be borne by Seller only if such goods are proven to be defective, are covered by this warranty
and are returned within the warranty period stated above.

ASSEMBLY OF STACKABLE WORKBENCH DRAWER
Two people are recommended for assembly. Approximate assembly time: 20-25 minutes.
Tools required: slotted screwdriver, Phillips screwdriver, and 7/16”wrench or nut driver.
The reference numbers used throughout this sheet refer to the illustration on the back cover.
This is to help you to identify the various parts as they are mentioned.
4. Insert the drawer into the housing.
1. Remove the drawer (Ref. No. 1) from the housing (Ref. No. 2)
by rst pulling it to the full extent that the suspensions allow.
Once the drawer is fully open, move the plastic lever inside
the suspension member (Ref. No. 7) to release the suspension
sections.
NOTE: On one side of the
suspension you will need to
move the lever up; on the
opposite side, you will need
to move the lever down.
NOTE: One set of mounting brackets comes with the standard
steel top workbench. Additional sets of mounting brackets must
be purchased separately if attaching more than one drawer or
attaching a drawer to a modular workbench.
Assembly for Steel Top
2. Attach the two mounting brackets (Ref. No. 3) in the desired
location on the workbench top. It is most common to place the
drawer to either the far left or far right side of the bench, but
can be placed anywhere that there are two holes in the bench
top that are 15” apart. Secure with two 1/4”-20 x 5/8” bolts
(Ref. No. 9) per mounting bracket.
3. Attach the drawer housing to the mounting brackets. Secure
with four 1/4”-20 x 5/8” bolts.





Assembly for Wood Top
2. Using the housing as a template, mark the location of four
holes for wood screws onto the underside of the wood top.
The recommendation is 1/2” offset from front of the bench top.
Using a 5/32” drill bit, drill holes into the wood top, drilling
about
1/2” to 3/4” deep.
3. Secure the housing to the top, using four #14-3/4” hex head
slotted wood screws (Ref. No. 11).
4. Insert the drawer into the housing.
2. Bolt housing together with four 1/4”-20 bolts and nuts.
3. Insert the drawer into the housing.
Assembly for Drawer to Drawer
1. Remove the drawer from the housing by rst pulling it to the
full extent that the
suspensions allow.
Once the drawer is
fully open, move the
plastic lever
inside the
suspension
member to
release the
suspension
sections.
NOTE: On one side of the
suspension you will need to
move the lever up; on the
opposite side, you will need
to move the lever down.



1. Remove the drawer from the housing by rst pulling it to
the full extent that the suspensions allow. Once the drawer
is fully open, move the plastic lever inside the suspension
member to release the suspension sections.
NOTE: On one side of the
suspension you will need to
move the lever up; on the
opposite side, you will need
to move the lever down.



REPLACEMENT PARTS
.
REF. NO. DESCRIPTION PART NUMBERS
QTY.
1 Drawer
2 Drawer Housing
3 30” Mounting Bracket OR
36” Mounting Bracket
1
1
1
1
1
1
1
1
1
1
1
976CDW
976CDH
WBMC-30
WBMC-36
967T
WBDD-125D
SUSP-16
CL-1
**
**
**
8 1/4”-20 x 5/8” Bolt
9 1/4”-20 Nut
10 #14 x 3/4”Hex Head Slotted Wood Screw
4 Tray
5 Divider
6 Drawer Suspension
7 Cam Lock w/Keys
**Available Locally



1/4”-20 x 5/8” Bolt
(Ref No. 8)
1/4”-20 Nut
(Ref No. 9)
Drawer Housing
(Ref No 2)
Drawer (Ref No 1)
Mounting Brackets
(Ref No 3)

Tray (Ref No 4)

Divider
(Ref No 5)


Drawer Suspension
(Ref No 6)

Drawer
Suspension
(Ref No 6)

Cam Lock with Keys
(Ref No 7)
#14 x 1/4” Hex Head
Slotted Wood Screw
(Ref No. 10)
NOTE: Additional hardware may be included for replacement purposes.
Tennsco makes every effort to ensure that all units ship complete with all parts and arrive undamaged.
However, should your unit contain missing or damaged parts, please contact your purchase location.
49B142