Tennsco B-8400 User manual

ORDER REPLACEMENT PARTS DIRECT FROM TENNSCO
Please provide the following information: Contact: Tennsco Corp., P.O. Box 1888
•Model number Dickson, TN 37056-1888
•Part description and number as shown above [phone] [phone]
•Color Or fill out form at http://www.tennsco.com
1Back
(Quantity: 1)
(Part No. B-3884)
2Uprights
(Quantity: 2)
(Part No. B-1284)
3End Panels
(Quantity: 2)
(Part No. B-84E)
4Bottom Shelf
(Quantity: 1)
(Part No. B-12B)
5Top Shelf
(Quantity: 1)
(Part. No. B-1238)
6Adjustable Shelves
(Quantity: 6)
(Part No. B-12)
7Tinnerman Clip
(Quantity: 18)
C1787
910-24 x 1/2" Bolts & Nuts
(Quantity: 12 each)
(Available Locally)
11 Shelf Divider
(Quantity: 7)
(Part No. B-1)
8#10 x 1/2" Sheet Metal
Screws (Quantity: 18)
(Available Locally)
10 Wrench/Screwdriver
Tool (Quantity: 1)
(Available Locally)
ASSEMBLY INSTRUCTIONS & PARTS MANUAL #1550499
KD BOOKCASE
Models B-8400
Tennsco Corp., Dickson, TN 37056-1888 * [phone]
CONGRATULATIONSonyourselectionofa
TENNSCO B-8400 bookcase! Tennsco
bookcases combine the strength you need
with the versatility of easily adjustable
shelves. Features include seven heavy-duty
reinforced shelves to handle loads of up to
200 pounds per shelf, a raised base to keep
materials safe from mops and damaging
cleaners; double wall construction to keep
materials from slipping behind uprights; and
slottedshelvestoallowforshelfdividers.Top
it off with our tough baked-on enamel finish,
and you have a shelving unit which will
remain attractive through years service.
Be Sure To Save This Instruction Sheet For Future Reference!
GENERAL SAFETY INFORMATION
Some parts may have sharp edges. CARE must be taken
when handling various pieces to avoid injury. Forsafety, wear
a pair of work gloves when assembling or performing any
maintenance on shelving unit. Shelving unit is designed to be
placed upright on a flat surface. Distribute the weight of items
storedon theshelvesevenly acrossthe shelves. Donotplace
heavier items on the upper shelves. If the shelving unit is to
be located in an uneven manner or positioned on an unlevel
surface, the unit should be secured to a wall or floor with
appropriate fasteners. Do not use as a ladder!
LIMITED WARRANTY
Tennsco warrants goods purchased hereunder to be free of defects
in materials and workmanship for a period of one (1) year from the
date of shipment, hereunder. This warranty shall not apply in the
event goods are damaged as a result of misuse, abuse, neglect,
accident, improper application, modification or repair by persons not
authorized by Seller, where goods are damaged during shipment, or
wherethe datestampsonthegoodshavebeendefaced, modified or
removed. UNLESS CONSIDERED UNENFORCEABLE OR
UNLAWFUL UNDER APPLICABLE LAW:
a. ALL IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO
WARRANTIES OR MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE ARE HEREBY EXCLUDED.
b. BUYERS REMEDY, IF ANY, FOR ANY DEFECTIVE GOODS
SHALL BE LIMITED TO A REFUND BY SELLER OR
REPLACEMENT OF THE GOODS AT SELLER’S OPTION, AND
SHALL IN NO EVENT INCLUDE DAMAGES OF ANY KIND,
WHETHER INCIDENTAL, CONSEQUENTIAL OR OTHERWISE.
NO GOODS ACCEPTED FOR RETURN WITHOUT PRIOR
APPROVAL. Seller shall have the right to inspect any goods claimed
to be defective at Buyers place of business or require Buyer to return
the goods to Seller for inspection on Seller’s premises. Transportation
charges covering returned goods will be borne by Seller only if such
goods are proven tobe defective, are covered by thiswarranty and are
returned within the warranty period stated above.
11. A. Bolt back to top using three
10-24 x 1/2 bolts and nuts.
B. Bolt rear corners at back to top
using sheet metal screws in
tinnerman clips already
inserted. B
BA
12. Bolt front of top to each upright using two
tinnerman clips (which were inserted in
step 9) and two sheet metal
screws. These holes are
hidden underneath the
front lip of the
bookcase top.
11
14. Place the seven dividers (Ref.
No. 11) as desired. Your 8400
Bookcase is now ready for
use.
13. Slide all remaining shelves
into desired position.
PARTS LIST
Numbers in upper left hand corner correspond to the reference numbers given throughout the instructions.
Some extra hardware may be included with your unit. Any extra pieces not listed below may be discarded.
Unit Dimensions: 38"w x 12"d x 84"h

Step By Step Installation Instructions
Tools required: One phillips screwdriver and a 3/8" wrench or nutdriver.
Unit should be assembled on any convenient, non-marring flat surface.
1. Remove all parts from carton and
check against the parts list on back
cover for any missing parts.
3. Place uprights (Ref. No. 2)
on either side of the back.
Be sure that the flat edge of
the upright is facing outward
as shown in exploded
view at right.
NOTE: There is no
"right" or "left" upright;
both uprights are the
same. There is a small
unslotted area at the
end of each upright; when
properly installed, these will
not be directly across from
each other, but on opposite
ends of the unit.
2
2
2. Place back (Ref. No. 1)
on a flat surface.
6. A. Secure bottom shelf to uprights with two
10-24 x 1/2 bolts (Ref. No. 9) and two
nuts (Ref. No. 10) on each end.
B. Insert one 10-24 x 1/2 bolt and nut in the
center of each end of bottom shelf and upright.
C. Bolt bottom shelf to back of bookcase with
three 10-24 x 1/2 bolts and nuts.
4. Fasten each upright to
the back using tinnerman
clips (Ref. No. 7). Place one tinnerman
clip over each of the slotted holes
(see exploded view at right for example).
NOTE: Do not place the screws into the
tinnerman clips yet. The back will be
screwed into place in step 8.
1
3
5. Place bottom shelf (Ref. No. 4) into position by slipping into slots on
uprights. It may be necessary to pry uprights apart slightly to
move bottom shelf into position.
NOTE:
As mentioned in Step 2, the uprights have an
unslotted area at one end which will be at the top of
the unit on one side and at the bottom of the unit on
the other side. This means that the bottom shelf will
be inserted in the second slot from the bottom on the
upright with slots all the way to the bottom, but in the
first slot from the bottom on the opposite upright (the
one with the slotless area at the bottom).
7. Temporarily insert a shelf
(Ref. No. 6) near the top of
the unit to keep uprights
stationary after unit is turned
on side.
7
4
A
A
B
C
B
6
8. Turn bookcase on one side and hook one end panel
(Ref. No. 3) over the front of the upright. Then slip the
end panel around the back of the unit and over the
tinnerman clips (some force may be required to do this).
Secure the end panel to the back by tightening six sheet
metal screws (Ref. No. 8) into the tinnerman clips. When
this is completed, turn the unit onto the opposite side and
repeat this procedure.
10. Set unit upright and place the top shelf
(Ref. No. 5) into position. The edges of
the shelf will fit on the outside of the
two uprights and the back. The
Tennsco logo should face the
front of the
bookcase.
(Instructions continue
on next page)
9. At the front of the top of each upright,
place a tinnerman clip over
the slotted hole as
shown.
5
910
8
PK-1550499

Step By Step Installation Instructions
Tools required: One phillips screwdriver and a 3/8" wrench or nutdriver.
Unit should be assembled on any convenient, non-marring flat surface.
1. Remove all parts from carton and
check against the parts list on back
cover for any missing parts.
3. Place uprights (Ref. No. 2)
on either side of the back.
Be sure that the flat edge of
the upright is facing outward
as shown in exploded
view at right.
NOTE: There is no
"right" or "left" upright;
both uprights are the
same. There is a small
unslotted area at the
end of each upright; when
properly installed, these will
not be directly across from
each other, but on opposite
ends of the unit.
2
2
2. Place back (Ref. No. 1)
on a flat surface.
6. A. Secure bottom shelf to uprights with two
10-24 x 1/2 bolts (Ref. No. 9) and two
nuts (Ref. No. 10) on each end.
B. Insert one 10-24 x 1/2 bolt and nut in the
center of each end of bottom shelf and upright.
C. Bolt bottom shelf to back of bookcase with
three 10-24 x 1/2 bolts and nuts.
4. Fasten each upright to
the back using tinnerman
clips (Ref. No. 7). Place one tinnerman
clip over each of the slotted holes
(see exploded view at right for example).
NOTE: Do not place the screws into the
tinnerman clips yet. The back will be
screwed into place in step 8.
1
3
5. Place bottom shelf (Ref. No. 4) into position by slipping into slots on
uprights. It may be necessary to pry uprights apart slightly to
move bottom shelf into position.
NOTE:
As mentioned in Step 2, the uprights have an
unslotted area at one end which will be at the top of
the unit on one side and at the bottom of the unit on
the other side. This means that the bottom shelf will
be inserted in the second slot from the bottom on the
upright with slots all the way to the bottom, but in the
first slot from the bottom on the opposite upright (the
one with the slotless area at the bottom).
7. Temporarily insert a shelf
(Ref. No. 6) near the top of
the unit to keep uprights
stationary after unit is turned
on side.
7
4
A
A
B
C
B
6
8. Turn bookcase on one side and hook one end panel
(Ref. No. 3) over the front of the upright. Then slip the
end panel around the back of the unit and over the
tinnerman clips (some force may be required to do this).
Secure the end panel to the back by tightening six sheet
metal screws (Ref. No. 8) into the tinnerman clips. When
this is completed, turn the unit onto the opposite side and
repeat this procedure.
10. Set unit upright and place the top shelf
(Ref. No. 5) into position. The edges of
the shelf will fit on the outside of the
two uprights and the back. The
Tennsco logo should face the
front of the
bookcase.
(Instructions continue
on next page)
9. At the front of the top of each upright,
place a tinnerman clip over
the slotted hole as
shown.
5
910
8
PK-1550499

ORDER REPLACEMENT PARTS DIRECT FROM TENNSCO
Please provide the following information: Contact: Tennsco Corp., P.O. Box 1888
•Model number Dickson, TN 37056-1888
•Part description and number as shown above [phone] [phone]
•Color Or fill out form at http://www.tennsco.com
1Back
(Quantity: 1)
(Part No. B-3884)
2Uprights
(Quantity: 2)
(Part No. B-1284)
3End Panels
(Quantity: 2)
(Part No. B-84E)
4Bottom Shelf
(Quantity: 1)
(Part No. B-12B)
5Top Shelf
(Quantity: 1)
(Part. No. B-1238)
6Adjustable Shelves
(Quantity: 6)
(Part No. B-12)
7Tinnerman Clip
(Quantity: 18)
C1787
910-24 x 1/2" Bolts & Nuts
(Quantity: 12 each)
(Available Locally)
11 Shelf Divider
(Quantity: 7)
(Part No. B-1)
8#10 x 1/2" Sheet Metal
Screws (Quantity: 18)
(Available Locally)
10 Wrench/Screwdriver
Tool (Quantity: 1)
(Available Locally)
ASSEMBLY INSTRUCTIONS & PARTS MANUAL #1550499
KD BOOKCASE
Models B-8400
Tennsco Corp., Dickson, TN 37056-1888 * [phone]
CONGRATULATIONSonyourselectionofa
TENNSCO B-8400 bookcase! Tennsco
bookcases combine the strength you need
with the versatility of easily adjustable
shelves. Features include seven heavy-duty
reinforced shelves to handle loads of up to
200 pounds per shelf, a raised base to keep
materials safe from mops and damaging
cleaners; double wall construction to keep
materials from slipping behind uprights; and
slottedshelvestoallowforshelfdividers.Top
it off with our tough baked-on enamel finish,
and you have a shelving unit which will
remain attractive through years service.
Be Sure To Save This Instruction Sheet For Future Reference!
GENERAL SAFETY INFORMATION
Some parts may have sharp edges. CARE must be taken
when handling various pieces to avoid injury. Forsafety, wear
a pair of work gloves when assembling or performing any
maintenance on shelving unit. Shelving unit is designed to be
placed upright on a flat surface. Distribute the weight of items
storedon theshelvesevenly acrossthe shelves. Donot place
heavier items on the upper shelves. If the shelving unit is to
be located in an uneven manner or positioned on an unlevel
surface, the unit should be secured to a wall or floor with
appropriate fasteners. Do not use as a ladder!
LIMITED WARRANTY
Tennsco warrants goods purchased hereunder to be free of defects
in materials and workmanship for a period of one (1) year from the
date of shipment, hereunder. This warranty shall not apply in the
event goods are damaged as a result of misuse, abuse, neglect,
accident, improper application, modification or repair by persons not
authorized by Seller, where goods are damaged during shipment, or
wherethe date stamps onthe goods have been defaced, modified or
removed. UNLESS CONSIDERED UNENFORCEABLE OR
UNLAWFUL UNDER APPLICABLE LAW:
a. ALL IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO
WARRANTIES OR MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE ARE HEREBY EXCLUDED.
b. BUYERS REMEDY, IF ANY, FOR ANY DEFECTIVE GOODS
SHALL BE LIMITED TO A REFUND BY SELLER OR
REPLACEMENT OF THE GOODS AT SELLER’S OPTION, AND
SHALL IN NO EVENT INCLUDE DAMAGES OF ANY KIND,
WHETHER INCIDENTAL, CONSEQUENTIAL OR OTHERWISE.
NO GOODS ACCEPTED FOR RETURN WITHOUT PRIOR
APPROVAL. Seller shall have the right to inspect any goods claimed
to be defective at Buyers place of business or require Buyer to return
the goods to Seller for inspection on Seller’s premises. Transportation
charges covering returned goods will be borne by Seller only if such
goods are proven tobe defective, are covered by thiswarranty and are
returned within the warranty period stated above.
11. A. Bolt back to top using three
10-24 x 1/2 bolts and nuts.
B. Bolt rear corners at back to top
using sheet metal screws in
tinnerman clips already
inserted. B
BA
12. Bolt front of top to each upright using two
tinnerman clips (which were inserted in
step 9) and two sheet metal
screws. These holes are
hidden underneath the
front lip of the
bookcase top.
11
14. Place the seven dividers (Ref.
No. 11) as desired. Your 8400
Bookcase is now ready for
use.
13. Slide all remaining shelves
into desired position.
PARTS LIST
Numbers in upper left hand corner correspond to the reference numbers given throughout the instructions.
Some extra hardware may be included with your unit. Any extra pieces not listed below may be discarded.
Unit Dimensions: 38"w x 12"d x 84"h