Tennsco ESPC-1236 Instruction Manual

PK-2701218
ASSEMBLY INSTRUCTIONS & PARTS MANUAL
RETAIN INSTRUCTIONS FOR FUTURE REFERENCE
Closed ESP Shelving
Models ESPC-1236, ESPC-1836, ESPC-2436,
ESPC-6-1236, ESPC-6-1836, ESPC-6-2436
Tennsco LLC. , Dickson, TN 37056-1888 • [phone]
GENERAL SAFETY INFORMATION
Some parts may have sharp edges. CARE must be taken when handling various pieces to avoid injury.
For safety, wear a pair of work gloves when assembling or performing any maintenance on the units.
LIMITED WARRANTY
Tennsco warrants goods purchased hereunder to be free of defects in materials and workmanship for a period of one (1) year from the date of shipment, hereunder. This warranty shall not apply in
the event goods are damaged as a result of misuse, abuse, neglect, accident, improper application, modication or repair by persons not authorized by Seller, where goods are damaged during
shipment, or where the date stamps on the goods have been defaced, modied or removed. UNLESS CONSIDERED UNENFORCEABLE OR UNLAWFUL UNDER APPLICABLE LAW:
a. ALL IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO WARRANTIES OR MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY EXCLUDED:
b. BUYERS REMEDY, IF ANY, FOR ANY DEFECTIVE GOODS SHALL BE LIMITED TO A REFUND BY SELLER OR REPLACEMENT OF THE GOODS AT SELLER’S OPTION, AND SHALL IN NO
EVENT INCLUDE DAMAGES OF ANY KIND, WHETHER INCIDENTAL, CONSEQUENTIAL OR OTHERWISE.
NO GOODS ACCEPTED FOR RETURN WITHOUT PRIOR APPROVAL. Seller shall have the right to inspect any goods claimed to be defective at Buyers place of business or require Buyer to return the
goods to Seller for inspection on Seller’s premises. Transportation charges covering returned goods will be borne by Seller only if such goods are proven to be defective, are covered by this warranty
and are returned within the warranty period stated above.
LOAD CAPACITIES
PER SHELF LEVEL
250 lbs.
ESPC-6-1236
ESPC-2436

ASSEMBLY OF CLOSED ESP SHELVING
Two people are recommended for assembly. Approximate assembly time: 10-15 minutes.
2. The unit back is shipped in two pieces. Place the two halves
of the unit back (Ref. No. 1) at on the ground and bolt
together with 1/4” - 20 nuts (Ref. No. 4) and 1/4” - 20 x 5/8”
bolts (Ref. No. 5), spaced 16 or 17 inches apart. The top three
holes should be left empty to leave room for the unit top.
1. The reference numbers used throughout this sheet refer
to the illustration on the back cover. This is to help you
to identify the various parts as they are mentioned.
3. Keep the back on a at on the ground and attach one end
panel (Ref. No. 3) to it by using 1/4” - 20 nuts and 1/4” - 20
x
5/8” bolts and nuts spaced 16 to 17 inches apart as described in
step 2. Once again, leave the top three holes empty to allow for
the top shelf. 5. Insert four shelf clips (Ref. No. 6) into the top two slots of
each side of both end panels.
4. Attach the second end panel in the same manner as in
step 3 on the opposite side of the back panels.

NOTE: When bolting the unit together, leave the bolts
slightly loose until the end of step 9, as binding may
occur during shelf placement.





6. Place the top shelf (Ref. No. 2) over the four clips at the top
of the unit. Be sure that the shelf is pushed securely into
the clips.
7. Insert four shelf clips into the bottom slots of the end panels
in the same way that you did in the top of the unit in step 5.
8. Place a shelf into the bottom four clips as in step 6.
9. Position the remaining shelf clips according to the desired
shelf heights, and place the shelves over the clips. Keep in
mind while placing the clips, that the post hole pattern
of two round holes and then one square hole, repeated
every 3 inches can greatly help in positioning the clips at
the same level.
NOTE: Once the bottom shelf is in place, carefully
lift the top end of the unit with the help of an
associate, so that the shelving unit is standing
upright.
NOTE: Some shelves, depending upon their placement,
could possibly require repositioning of some of the
back and end panel bolts in order to insert the shelf.
Once everything is correctly positioned tighten the bolts.










REPLACEMENT PARTS

End Panel
(Ref No. 3)
NOTE: Additional hardware may be included for replacement purposes.
Tennsco makes every effort to ensure that all units ship complete with all parts and arrive undamaged.
However, should your unit contain missing or damaged parts, please contact your purchase location.
REF.
NO.
ESPC-1236 ESPC-6-1236 ESPC-1836 ESPC-6-1836 ESPC-2436 ESPC-6-2436
PART NO. 36w x 12d 36w x 18d 36w x 24d
DESCRIPTION
1
2
3
4
5
6
2 Piece Back Panels
Shelves
End Panels
1/4
”-20 Nuts
1/4
”-20
5/8
” Bolts
ESP Shelving Clips
ESPBP-3675
ES-12
ES-18
ES-24
ESPCU-1275
ESPCU-1875
ESPCU-2475
*
*
ESPCLIP
1
5
2
20
20
20
1
6
2
24
24
24
1
5
2
20
20
20
1
6
2
24
24
24
1
6
2
24
24
24
1
5
2
20
20
20

2 Piece Back Panel
(Ref No. 1)

Shelves
(Ref No. 2)

ESP Shelving Clips
(Ref No. 6)
49B270
1/4”-20 5/8” Bolt
(Ref No. 5)
1/4”-20 Nut
(Ref No. 4)