Tennsco APT-3672S Instruction Manual

ASSEMBLY INSTRUCTIONS & PARTS MANUAL
PK-1880620PK-1880620
Packing Table
RETAIN INSTRUCTIONS FOR FUTURE REFERENCERETAIN INSTRUCTIONS FOR FUTURE REFERENCE
Tennsco LLC., Dickson, TN 37056-1888 • [phone]
GENERAL SAFETY INFORMATIONGENERAL SAFETY INFORMATION
Some parts may have sharp edges. CARE must be taken when handling various pieces to avoid injury.
For safety, wear a pair of work gloves when assembling or performing any maintenance.
LIMITED WARRANTYLIMITED WARRANTY
Tennsco warrants goods purchased hereunder to be free of defects in materials and workmanship for a period of one (1) year from the date of shipment, hereunder. This warranty shall not apply in
the event goods are damaged as a result of misuse, abuse, neglect, accident, improper application, modication or repair by persons not authorized by Seller, where goods are damaged during
shipment, or where the date stamps on the goods have been defaced, modied or removed. UNLESS CONSIDERED UNENFORCEABLE OR UNLAWFUL UNDER APPLICABLE LAW:
a. ALL IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO WARRANTIES OR MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY EXCLUDED:
b. BUYERS REMEDY, IF ANY, FOR ANY DEFECTIVE GOODS SHALL BE LIMITED TO A REFUND BY SELLER OR REPLACEMENT OF THE GOODS AT SELLER’S OPTION, AND SHALL IN NO
EVENT INCLUDE DAMAGES OF ANY KIND, WHETHER INCIDENTAL, CONSEQUENTIAL OR OTHERWISE.
NO GOODS ACCEPTED FOR RETURN WITHOUT PRIOR APPROVAL. Seller shall have the right to inspect any goods claimed to be defective at Buyers place of business or require Buyer to return the
goods to Seller for inspection on Seller’s premises. Transportation charges covering returned goods will be borne by Seller only if such goods are proven to be defective, are covered by this warranty
and are returned within the warranty period stated above.
APT-3672SAPT-3672S APT-3672WAPT-3672W withwith
PTP-60PTP-60
TWBR-60TWBR-60
TWCTL-48TWCTL-48
TWLB-60TWLB-60

ASSEMBLY OF PACKING TABLE
Two people are recommended for assembly.
Tools required: Phillips screwdriver and 7/16”wrench or nut driver.
The reference numbers used throughout this sheet refer to the illustration on the back cover.
This is to help you to identify the various parts as they are mentioned.
3. For assembly of a butcher block top, lay the top on a at
surface. Align the leg with the eight pre-drilled pilot holes.
Attach with eight #14 x ¾” hex head slotted wood screws
(Ref. No. 14). Repeat with second leg. Once nished,
proceed to step 4.
2. Align the workbench leg (Ref. No. 2) with the four end holes.
Attach the leg with four 1/4”-20 x 5/8” bolts (Ref. No. 12) through
the leg and the top. Then secure with 1/4”-20 Nuts (Ref. No. 13).
Repeat with the second leg. Once nished, proceed to step 4.
4. Turn workbench over. Place the lower shelf (Ref. No. 3) on
the brace of each leg. Attach with three 1/4”-20 x 5/8” bolts
and nuts on each end of the shelf.


1. For assembly of a butcher block top, proceed to step 3.
For assembly of a steel top packing table, lay (Ref. No. 1) face
down on a protected at surface. Attach the two mounting
brackets under the lip of the bench top for extra support, using
one bolt on each end of both brackets. The brackets should be
evenly spaced for maximum support. Continue to step 2.
NOTE: If installing the optional workbench drawer,
refer to the instructions supplied with the drawer
positioning of the mounting brackets.

NOTE: The above diagram shows all the
accessories available.

6. Attach the accessories (Ref. No.’s 5 - 11). Angle the piece
so the back of the hooks are just above the holes on the
upright frames. Slide the hooks into the holes and push
down. Ensure both sides of each accessory is on the same
level of holes on each upright.
5. Attach the divider shelf to the cantilever upright frames.
(See step 6 on how to attach). Using the help of an
associate, place the upright frames with the divider
shelf attached to the packing table. Use this as
a template to mark the locations for the holes in the
top. Remove the cantilever system off the top and
unhook the divider shelf from the uprights.
For steel tops, drill four 5/16” holes into the top. Then
attach the uprights to the top using 1/4”-20 x 5/8” bolts and
nuts, with a at washer under the top for security.
For wood tops, drill 5/32” pilot holes 3/4” deep. Use #14 x ¾”
hex head slotted wood screws to attach each upright to the
top.





REPLACEMENT PARTSREPLACEMENT PARTS
REF. NO.REF. NO. PART NUMBERSPART NUMBERS QTY.QTY.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
1
1
1
1
2
2
1
1
1
1
1
1
1
1
1
34
22
24
30” Deep Steel Top
36” Deep Steel Top
30” Deep Butcher Block Top
36” Deep Butcher Block Top
30” Deep Adjustable Leg
36” Deep Adjustable Leg
72” Wide Lower Shelf
Cantilever Upright Frames
Eye Level Shelf
Divider Shelf
Roll Dispenser
Optional Power Rail
Optional Bin Rail
Optional Task Light
Optional Task Light Bracket Kit
1/4”-20 x 5/8” Bolt
1/4”-20 Nut
#14 x 3/4”Hex Head Slotted Wood Screw
G-T-3072 OR
G-T-3672 OR
G-MT-3072 OR
G-MT-3672
AL-3230 OR
AL-3236
S-72
WBRU-42A
WFS-60A
WBBS-60
WBPRD-60A
PTP-60
TWBR-60
TWCTL-48
TWLB-60
**
**
**
**Available Locally



1/4”-20 x 5/8” Bolt
(Ref No. 12)(Ref No. 12)
1/4”-20 Nut
(Ref No. 13)(Ref No. 13)
Divider ShelfDivider Shelf
(Ref No 6)(Ref No 6)
TopTop
(Ref No 1)(Ref No 1)
Lower ShelfLower Shelf
(Ref No 3)(Ref No 3)

Cantilever UprightCantilever Upright
FramesFrames
(Ref No 4)(Ref No 4)



Adjustable LegAdjustable Leg
(Ref No 2)(Ref No 2)


#14 x 1/4” Hex Head
Slotted Wood Screw
(Ref No. 14)(Ref No. 14)
NOTE: Additional hardware may be included for replacement purposes.NOTE: Additional hardware may be included for replacement purposes.
Tennsco makes every effort to ensure that all units ship complete with all parts and arrive undamaged.Tennsco makes every effort to ensure that all units ship complete with all parts and arrive undamaged.
However, should your unit contain missing or damaged parts, please contact your purchase location.However, should your unit contain missing or damaged parts, please contact your purchase location.
49B18849B188
DESCRIPTIONDESCRIPTION
Eye Level ShelfEye Level Shelf
(Ref No 5)(Ref No 5)

Roll DispenserRoll Dispenser
(Ref No 7)(Ref No 7)
Power RailPower Rail
(Ref No 8)(Ref No 8)
Task Light BracketTask Light Bracket
(Ref No 11)(Ref No 11)
Task LightTask Light
(Ref No 10)(Ref No 10)
Bin RailBin Rail
(Ref No 9)(Ref No 9)