Teridian 73S1217F User manual

Simplifying System Integration
TM
73S1217F
Evaluation Board Lite User Guide
August 17, 2009
Rev. 1.2
UG_1217F_046

73S1217F Evaluation Board Lite User Guide UG_1217F_046
2 Rev. 1.2
© 2009 Teridian Semiconductor Corporation. All rights reserved.
Teridian Semiconductor Corporation is a registered trademark of Teridian Semiconductor Corporation.
Simplifying System Integration is a trademark of Teridian Semiconductor Corporation.
Microsoft, Windows and Vista are registered trademarks of Microsoft Corporation.
Signum is a trademark of Signum Systems Corporation.
Keil is a trademark of ARM®Ltd.
Linux is a registered trademark of Linus Torvalds.
Slackware is a registered trademark of Patrick Volkerding and Slackware Linux, Inc.
Fedora is a registered trademark of RedHat, Inc.
All other trademarks are the property of their respective owners.
Teridian Semiconductor Corporation makes no warranty for the use of its products, other than expressly
contained in the Company’s warranty detailed in the Teridian Semiconductor Corporation standard Terms
and Conditions. The company assumes no responsibility for any errors which may appear in this
document, reserves the right to change devices or specifications detailed herein at any time without
notice and does not make any commitment to update the information contained herein. Accordingly, the
reader is cautioned to verify that this document is current by comparing it to the latest version on
http://www.teridian.com or by checking with your sales representative.
Teridian Semiconductor Corp., 6440 Oak Canyon, Suite 100, Irvine, CA 92618
TEL [phone], FAX [phone], http://www.teridian.com

UG_1217F_046 73S1217F Evaluation Board Lite User Guide
Rev. 1.2 3
Table of Contents
1Introduction ...................................................................................................................................4
1.1 Evaluation Board Lite Package Contents ..............................................................................5
1.2 Evaluation Board Lite Features.............................................................................................5
1.3 Recommended Equipment and Test Tools............................................................................5
2Evaluation Board Lite Basic Setup...............................................................................................6
2.1 Using the Evaluation Board Lite with an Emulation Tool........................................................7
2.2 Loading User Code into the Evaluation Board-Lite ................................................................7
3Using the USB CCID Application..................................................................................................9
3.1 Driver and Software Installation.............................................................................................9
3.2 Frequently Asked Questions...............................................................................................10
4Evaluation Board Lite Hardware Description.............................................................................12
4.1 Jumpers, Switches and Test Points.....................................................................................12
4.2 Schematic...........................................................................................................................15
4.3 PCB Layouts.......................................................................................................................16
4.4 Bill of Materials ...................................................................................................................19
4.5 Schematic Information ........................................................................................................21
4.5.1 Reset Circuit..............................................................................................................21
4.5.2 Oscillators .................................................................................................................21
4.5.3 USB Interface............................................................................................................22
4.5.4 Smart Card Interface .................................................................................................22
5Ordering Information...................................................................................................................24
6Related Documentation...............................................................................................................24
7Contact Information.....................................................................................................................24
Revision History..................................................................................................................................25
Figures
Figure 1: 73S1217F Evaluation Board Lite...............................................................................................4
Figure 2: 73S1217F Evaluation Board Lite Basic Connections.................................................................6
Figure 3: Emulator Window Showing RESETand ERASE Buttons...........................................................8
Figure 4: Emulator Window Showing Erased Flash Memory and File Load Menu.....................................8
Figure 9: 73S1217F Evaluation Board Lite Jumper, Switch and Test Point Locations.............................14
Figure 10: 73S1217F Evaluation Board Lite Electrical Schematic...........................................................15
Figure 11: 73S1217F Evaluation Board Lite Top View (Silkscreen) ........................................................16
Figure 12: 73S1217F Evaluation Board Lite Bottom View (Silkscreen) ...................................................16
Figure 13: 73S1217F Evaluation Board Lite Top Signal Layer................................................................17
Figure 14: 73S1217F Evaluation Board Lite Middle Layer 1 – Ground Plane..........................................17
Figure 15: 73S1217F Evaluation Board Lite Middle Layer 2 – Supply Plane...........................................18
Figure 16: 73S1217F Evaluation Board Lite Bottom Signal Layer...........................................................18
Figure 5: External Components for RESET............................................................................................21
Figure 6: Oscillator Circuit......................................................................................................................21
Figure 7: USB Connections ...................................................................................................................22
Figure 8: Smart Card Connections.........................................................................................................23
Tables
Table 1: Flash Programming Interface Signals.........................................................................................7
Table 2: Evaluation Board Lite Jumper, Switch and Test Point Description.............................................12
Table 3: 73S1217F Evaluation Board Lite Bill of Materials......................................................................19

73S1217F Evaluation Board Lite User Guide UG_1217F_046
4 Rev. 1.2
1 Introduction
The Teridian Semiconductor Corporation (TSC) 73S1217F Evaluation Board Lite is used as a platform to
demonstrate the capabilities of the 73S1217F Smart Card Controller devices. It has been designed to
operate either as a standalone or a development platform.
The 73S1217F Evaluation Board Lite can be programmed to run any of the Teridian turnkey applications
or a user-developed custom application. Teridian provides its USB CCID application preloaded on the
board and an EMV testing application on the CD.
Applications can be downloaded through the In-Circuit-Emulator (ICE) or through the TSC Flash
Programmer Model TFP2. As a development tool, the Evaluation Board Lite has been designed to
operate in conjunction with an ICE to develop and debug 73S1217F based embedded applications.
Figure 1: 73S1217F Evaluation Board Lite

UG_1217F_046 73S1217F Evaluation Board Lite User Guide
Rev. 1.2 5
1.1 Evaluation Board Lite Package Contents
The 73S1217F Evaluation Board Lite package contains the following:
•73S1217F Evaluation Board Lite: 4-layer, square PWB as shown in Figure 1, containing the
73S1217F with the preloaded turnkey USB CCID application.
•USB cable, A-B, male, 2 meters.
•CD containing documentation (data sheet, board schematics, BOM and layout), Software API
libraries, evaluation code and utilities.
1.2 Evaluation Board Lite Features
The 73S1217F Evaluation Board Lite (see Figure 1) includes the following:
•USB 2.0 full speed interface
•RS-232 interface
•Single smart card interface
•Battery backup power interface
•ICE/Programmer interface
•ON/OFF switch for battery backup operation
•Real Time Clock (RTC) capability
•1 LED
1.3 Recommended Equipment and Test Tools
The following equipment and tools (not provided) are recommended for use with the 73S1217F
Evaluation Board Lite package:
•For functional evaluation: PC with Microsoft®Windows®XP or Vista®, or a Linux®workstation
equipped with a USB port or an RS232 (COM) port with a DB9 connector.
•For software development (MPU code)
Signum™ ICE (In Circuit Emulator): ADM-51. Refer to
http://signum.temp.veriohosting.com/Signum.htm.
Keil™ 8051 C Compiler Kit: CA51. Refer to http://www.keil.com/c51/ca51kit.htm and
http://www.keil.com/product/sales.htm.

73S1217F Evaluation Board Lite User Guide UG_1217F_046
6 Rev. 1.2
2 Evaluation Board Lite Basic Setup
Figure 2shows the basic connections of the Evaluation Board-Lite with the external equipment.
The power supply can come from two sources:
•The +5 V coming from the USB bus (default) when connected to acomputer or hub ableto support USB
powered devices. In this case the ON/OFF switch, S2, has no effect and power is always on. When
the board is powered from the USB bus, the application is bus-powered and the embedded
application must be designed for this.
•Any AC-DC converter block able to generate a DC power supply of 4.0 V min to 6.5 V max at 400 mA
for backup power for those applications capable of using it.This power is connected to the PJ1
connector. When using the PJ1 power input, the ON/OFF switch, S2, controls the power to the
73S1217F.
The communication with an external host can be accommodated by either:
•A standard USB2.0 full speed interface or
•A standard RS-232 serial interface (TX/RX only).
The board provides by default the USB CCID application. Refer to Section 3for information on setting up
and running the USB CCID application.
Figure 2: 73S1217F Evaluation Board Lite Basic Connections

UG_1217F_046 73S1217F Evaluation Board Lite User Guide
Rev. 1.2 7
2.1 Using the Evaluation Board Lite with an Emulation Tool
The 73S1217F Evaluation Board Lite can operate with an In-Circuit-Emulator (ICE) from Signum Systems
(model ADM-51). The Signum System POD has a ribbon cable that must be directly attached to
connector J2 (see Figure 2).
Signum Systems offers different pod options depending on user needs. The standard pod allows users to
perform typical emulator functions such as symbolic debugging, in-line breakpoints, memory
examination/modification, etc. Other pod options enable code trace capability and/or complex
breakpoints at an additional cost.
When using an ICE, the board must be either USB bus powered or VBAT powered (and
turned on via the ON/OFF switch). The power LED D4 will indicate the power status.
2.2 Loading User Code into the Evaluation Board-Lite
The signals listed in Table 1are necessary for communication between the TFP2 Flash Programmer or
ICE and the 73S1217F.
Table 1: Flash Programming Interface Signals
Signal Direction Function
E_TCLK Output from 73S1217F Data clock
E_RXTX Bi-directional Data input/output
E_RST1Bi-directional Flash Downloader Reset (active low)
1The E_RST signal should only be driven by the TFP2 when enabling these
interface signals. The TFP2 must release E_RST at all other times.
The signals in Table 1, along with 3.3 V and GND, are available on the emulator header J2. Production
modules may be equipped with much simpler programming connectors, e.g. a 5x1 header.
Programming of the flash memory requires either the Signum Systems ADM51 in-circuit emulator or the
TSC Flash Programmer Model TFP2 provided by Teridian.
Loading Code with the In-Circuit Emulator
If firmware exists in the 73S1217F flash memory, the memory must be erased before loading a new file
into memory. In order to erase the flash memory, the RESET button in the emulator software must be
clicked followed by the ERASE button (see Figure 3).
Once the flash memory is erased, a new file can be loaded using the Load command in the File menu.
The dialog box shown in Figure 4makes it possible to select the file to be loaded by clicking the Browse
button. Once the file is selected, pressing the OK button loads the file into the flash memory of the IC.
At this point, the emulator probe (cable) can be removed. Once the 73S1217F device is reset using the
reset button on the evaluation board, the new code starts executing.
Loading Code with the TSC Flash Programmer Model TFP2
Follow the instructions given in the TSC Flash Programmer Model TFP2 User’s Manual.

73S1217F Evaluation Board Lite User Guide UG_1217F_046
8 Rev. 1.2
Figure 3: Emulator Window Showing RESET and ERASE Buttons
Figure 4: Emulator Window Showing Erased Flash Memory and File Load Menu
RESET
BUTTON
ERASE
BUTTON

UG_1217F_046 73S1217F Evaluation Board Lite User Guide
Rev. 1.2 9
3 Using the USB CCID Application
The USB CCID firmware is pre-installed on the 73S1217F Evaluation Board Lite. To operate correctly, it
requires a PC with the appropriate driver installed to be connected through its USB port. When powered-
up, the board is able to run with the demonstration host application included on the CD.
The demonstration application is named CCID-USB.vshost.exe and is located in the “C:\TSC\12xxF
Vy.yy\CCID USB Host App C#\App\Bin” directory (where y.yy is the latest version of the firmware
release). This is a host application that allows:
•Smart card activation and deactivation, in ISO or EMV mode.
•Smart card APDU commands to be exchanged with the smart card inserted in the board.
•Starting a test sequence in order to test and evaluate the board performance against an EMV test
environment.
3.1 Driver and Software Installation
Installation on Windows XP
Two drivers are available for use with Windows XP:
•The standard Microsoft Windows XP driver and
•The Teridian provided driver that adds additional features beyond the capabilities of the Microsoft
driver. See the 73S1215F, 73S1217F CCID Application Note for further details on the differences
between the two drivers.
When using this 73S1217F Evaluation Board Lite, the Microsoft provided driver should be used used as
the TSC drivers extended features are not available on the Evaluation Board-Lite.
The Microsoft CCID driver included in the CD is used by Teridian for testing. Check with
Microsoft for the latest driver upgrades.
Follow these steps to install the software on a PC running Windows XP:
•Extract “12xxF CCID+DFU Vy.yy Release.zip” (where y.yy is the latest version of the firmware
release).
oCreate an install directory. For example: “C:\TSC\”.
oUnzip “12xxF CCID+DFU Vy.yy Release.zip” to the just created folder. All applications and
documentation needed to run the board with a Windows PC will be loaded to this folder. Plug the
supplied power adaptor into the DC Jack and a wall outlet. LED0 should now come on.
•Connect the USB cable between the host system and the 73S1217F Evaluation Board Lite. The host
system should recognize the board and start the Add New Hardware Installation wizard. When the
wizard prompts, select the Microsoft Windows standard driver:
oSelect the usbccid.inf file located in the “C:\TSC\12xxF CCID+DFU Vy.yy Release\USB-CCID
Firmware\CCID USB\CCID+DFU USB Drivers\MS Generic” subdirectory. The uscccid.inf and
usbccid.sys files must be in the same directory on the host.
•Follow the prompts until the process is completed.
•Run CCID-DFU_USB_vy.yy.exe (located in the path - C:\TSC\12xxF CCID+DFU C:\TSC\12xxF
CCID+DFU V2.00 Release\Host Applications\Windows App\Bin\Release Release\Host
Applications\Windows App\Bin\Release) on the host system to execute the host demonstration
application.
At this point the application window should appear. For additional information regarding the use of the
Teridian Host application, refer to the 73S12xxF USB-CCID Host GUI Users Guide (UG_12xxF_037).

73S1217F Evaluation Board Lite User Guide UG_1217F_046
10 Rev. 1.2
Installation on a Linux System
Teridian has tested 73S1217F Evaluation Board -Lite with the Linux CCID driver v1.3.2 and PCSC-Lite
v.1.4.4 (middleware) on two distributions of Linux: Slackware®6 with kernel 2.4.16, and Fedora®7 with
kernel 2.6.23. Refer to the 73S1215F, 73S1217F CCID USB Linux Driver Installation Guide
(UG_12xxF_041) for details on the Linux software installation and usage.
3.2 Frequently Asked Questions
Windows
Q: The PC/SC application starts but it shows a “No Reader Found” message.
A: Follow these steps to make sure:
1. The board has powered up properly (USB is securely connected and there is power applied to the
board).
2. Control Panel – System – Hardware – Device Manager – Smart Card Readers shows: “Teridian
Semiconductors USB CCID Smart Card Reader...” And there is no yellow “!” or red “X”.
3. Smart Card Service has started by going to “Control Panel – Administrative Tools – Services –
Smart Card”. Look under the “status” column and if it shows “stopped”, hit the restart or start
button to start it.
4. If all of the above look ok, hit the refresh button on the CCIDUSB.exe application.
Q: There is a yellow “!” on the Teridian driver shown on the Device Manager menu.
A: This usually means the driver did not complete the driver enumeration process. Push the reset button
on the development board a few times. If the board is connected to the host via a USB HUB, remove
the HUB and try connecting the development board directly to the PC USB port to make sure the
driver and the board can enumerate with the USB host. If the problem persists, check the driver on
the PC to make sure it is at least version 6.0.0.2. Contact your Teridian Sales Rep for the latest
version of the driver. Sometimes, rebooting the PC Host to clear up any previous USB problem will
help to resolve the problem.
Q: There is a red “X” on the Teridian driver shown on the Device Manager menu.
A: This usually means the smart card driver has been disabled. Highlight and right click on the driver to
re-enable.

UG_1217F_046 73S1217F Evaluation Board Lite User Guide
Rev. 1.2 11
Q: The Teridian Smart Reader is nowhere to be found on the Device Manager menu and there is an
“unknown USB device” found where the Teridian Evaluation Board Lite should be.
A: This usually means the development board is properly powered up but there is no enumeration taking
place. If the development board is connected to a USB HUB, remove the HUB and connect the board
directly to the PC USB port, or move it to a different USB port on the system. If the problem persists
and it is absolutely sure that the development board is properly powered up, it is possible that there is
no firmware in the part. Contact a Teridian sales representative for reprogramming of the Flash.
Q: The Teridian driver is loaded. What to do to replace it with the Microsoft Generic USB CCID driver?
A: Right click on the Teridian driver in the Device Manager Menu, select “Update Driver..”. Select “No,
Not this time” on the next menu, “Install from a list or specific location”, “Don’t Search, I will choose the
driver to install”. If the next menu does not show the Microsoft Generic USB CCID driver, select
“Have Disk” and browse to where the driver file resides (usually in the “CCID USB XPDriver” folder)
and select the file. Follow through with the installation wizard.
Linux
Q: How can I see debug messages from PCSC-Lite when I run pcscd from the command line?
A: Before invoking pcscd, open the file /usr/local/pcsc/drivers/ifd-ccid.bundle/Contents/Info.plist in an
editor, and set ifdLogLevel to 7. Save the change. Then run the command “pcscd –f –d” in a console.
Nowpcscd runs in foreground and should display many messages in the console. These messages
show information about the smart card readers that have been detected, and whether or not a smart
card is present in the reader. Also shown in the messages are the data exchanges between the host
(Linux) and the smart card reader. The most important messages are the error messages that pcscd
displays when a critical error has occurred. If fewer messages are desired, set IfdLogLevel to 3 or 1.
Q: When I run the command “pcscd –f –d”, I get an error message that says “file /var/run/pcscd.pub
already exists. Another pcscd seems to be running”.
A: Only one instance of pcscd (PCSC-Lite Daemon) should be running at any time. If you receive this
error message when invoking thepcscd program, pcscd is probably currently running already. If your
intention is to restart pcscd, first terminate thepcscdthat is currently running. You can run the
command “ps aux | grep pcscd” to obtain the PID (Process ID) of the current pcscd. For example, you
may see output similar to the following:
[root@localhost ~]# ps aux | grep pcscd
root3380 0.1 0.0 74588 1752 pts/2 Sl+ 16:06 0:02 pcscd –f –d
[root@localhost ~]#
The PID of pcscd in this case is 3380. Next run the command “kill 3380” to stop the currently running
pcscd. Then start pcscd again by entering the command “pcscd –f –d”.
Q: When I start the program pcsc_scan, I receive an error message saying “PCSC Not Running”.
A: The pcsc_scan program requires the services provided by pcscd. Hence the PCSC-Lite daemon
pcscdshould be already running before pcsc_scan can start. Run pcscd first, and then invoke
pcsc_scan.

73S1217F Evaluation Board Lite User Guide UG_1217F_046
12 Rev. 1.2
4 Evaluation Board Lite Hardware Description
4.1 Jumpers, Switches and Test Points
Table 2 describes the73S1217F Evaluation Board Lite jumpers, switches and modules. The Item # in
Table 2 references Figure 9.The default setting refers to setup for running USB-CCID application..
Table 2: Evaluation Board Lite Jumper, Switch and Test Point Description
Item
#
Schematic
and
Silkscreen
Reference
Default
setting Name Use
1 S1 Reset button Evaluation board main reset: Asserts a
hardware reset to the on-board 73S1217F.
2 S2 On / Off button
When using battery power (on PJ1), turns on or
off (toggles) power to the 73S1217F device.
3 TP8 VP test point Test point used for monitoring the VP voltage.
VP is 5.5 V when the 72S1217F is on.
4 TP2 ICC test point Smart card interface test points with ground
pins.
5 TP1 Vbat test point VBAT input test point.
6 TP3 USR pin test points USR pin test points.
7 PJ1 No
Connect DC Jack VBAT input power jack. VBAT use is optional
and must be between 4.0 V and 6.5 V. VBAT
draws power only when VBUS power is absent.
VBAT use is selected by means of the ON/OFF
switch.
8 TP6 VDD test point VDD test point with ground.
9 J2 No
Connect In-Circuit Emulator
connector This connector must be used when using an external In-Circuit Emulator(ADM51). Refer to
Electrical Schematic for pin assignments.
10 D5 RXD LED Reflects the activity on the serial RX: Data
going TO the 73S1217F.
11 TP4 Not
Inserted RXD LED jumper Jumper inserted enables RX LED. Jumper
removed disables RX LED.
12 D6 TXD LED Reflects the activity on the serial TX: Data
coming FROM the 73S1217F.
13 JP2 Not
Inserted Serial transceiver enable
jumper This jumper controls the RS-232 transceiver shutdown function. There are three possible
configurations:
•Removed; places RS-232 transceiver chip
in shutdown.
•Inserted VDD; enables RS-232 transceiver.
•Inserted USR6; allows USR6 pin to control
RS-232 transceiver shutdown.
14 TP5 Not
Inserted TXD LED jumper Jumper inserted enables TX LED. Jumper
removed disables TX LED.

UG_1217F_046 73S1217F Evaluation Board Lite User Guide
Rev. 1.2 13
Item
#
Schematic
and
Silkscreen
Reference
Default
setting Name Use
15 P1 No
Connect DB9 RS232 female
socket This socket allows connection of a RS232 cable to a computer. Use a crossed wired
(RX/TX) cable. The evaluation board has an
on-board level shifter (U7) to allow direct
connection to a computer.
16 JP1 Insert USB interrupt jumper This jumper allows VBUS (after levelconversion)
to connect toUSR7 (configured for interrupt).
Remove this jumper if not needed and USR7 can
be used for another purpose.
17 – Board reference and
serial number Should be mentioned in any communication with Teridian when requesting support.
18 J3 Connect USB connector Standard USB socket. Requires a standard
USB 1.1 or 2.0 device cable to connect to a
computer.
19 D4 Power LED Power LED – comes on with VDD. Can be
disabled by removing JP4.
20 JP4 Insert Power LED disable Inserting this jumper enables the power LED
with VDD. Removing the jumper disables the
power LED.
21 D1 LED0 73S1217F LED0 output LED.
22 TP7 VPC test point Test point to monitor VPC. VPC is the input
power source to the internal voltage converter.
This voltage is derived from either VBUS or
VBAT. See the 73S1217F Data Sheet
for further information.
23 J1 Smart Card connector Allows the evaluation board to communicate
with a smart card using a standard (credit card
size) format: This slot is connected to the
73S1217F external card interface.

73S1217F Evaluation Board User’s Guide
14
Figure 5: 73S1217F Evaluation Board Lite Jumper, Switch and Test Point Locations

UG_1217F_046 73S1217F Development Board User’s Guide
Rev. 1.2 15
4.2 Schematic
VDD
C29
0.1uF R23
200k
OSC_OUT_32OSC_OUT_32OSC_OUT_32OSC_OUT_32
USR0
USR2
Place R'S close to U4
Length and width of USB D+ and D- tracks
should be matched and routed away from
smart card CLK and VCCs
USR4
SERIAL
PORT
C4
OSC_IN_32OSC_IN_32OSC_IN_32OSC_IN_32
GND
R21 24
C5
27p
D+
TBUS[3]TBUS[3]
ISYNC/BRKRQ
1 2
JP4
D1
LED
C25
22pF
VDD
LED0
VDD
C24
22pF
TBUS[0]
R5
10k
VDD
USR6
1 2 3
JP2
HEADER 3_0
12 34 56 78 910 1112 1314 1516 1718 1920
J2
Emulator IF
232 SHDN
SEL
VDD
R7 62
R9 62
R10 62
R13 62
R17 62
R15 62
R14 62
R16 62
C27
22pF
C26
22pF
TBUS[1]
C28
22pF
RXTX
TCLK
TBUS[2]
RST_EMUL
1
SY M1
Logo
VBUS_MON
Enable
VBAT
VCC
1
RST
2
CLK
3
C4
4
GND
5
VPP
6
I/O
7
C8
8
SW-1
9
SW-2
10
J1
Smart Card Connector
C16
27pF
C11
22pF
C10
22pF
SMARTCARD
SLOT #1
USR1
USR2 USR7
R3
100K
USR5 USR6
USR4 USR3
1
2
3
4
5
6
7
8
TP3
HEADER 8
1
TP8
VP
R25
200k
R1 0
R18 680
R19 680
DPLUS DMINUS
VDD
D5
LED
D6
LED
POWER LED
Disable
RST
D-
GND
C9 should
be as close
as possible
to pin 54
VCC tracks should be
wider than 0.5mm.
DMINUS
USR6
USR0
+5VDC
VBAT
MOUNT HOLES FOR STAND OFFS
1
G1
1
G2
1
G3
1
G4
C9
4.7uF
1
TP7
1 2
TP4
RXD LED
Disable
12
S2
SW
VPC
TXDTXDTXDTXDTXDTXDTXDTXD
Y2
12.000MHz
R4
10
1 2
S1
SW
TXD LED
Disable
1 2
TP5
VDD
OSC_IN_12OSC_IN_12 OSC_OUT_12OSC_OUT_12
OSC_OUT_12
OSC_IN_12
OSC_OUT_32
OSC_IN_32
R2
1M
POWER
IO
USR7
L1
10uH
1 2
JP1
RESET
STATUS INDICATOR
+C13
10uF
RXD
C5 C6 and C7 should be
located close to the
Smart Card Connector
11
22
33
PJ1
+5VDC
VDD 68
RESET
1
SEC
2
ISBR
3
SCL
5
SDA
6
NC/X32OUT
7
NC/X32IN
8
GND
9
X12IN
10
X12OUT
11
COL0
12
COL1
13
COL2
14
ANAIN
15
COL3
16
RXD
17
TXD
18
COL4
19
USR7
20
ROW0
21
ROW1
22
USR6
23
ROW2
24
GND
25
DP
26
DM
27
VDD
28
USR5
29
USR4
30
USR3
31
USR2
32
ROW3
33
USR1
34
USR0 35
ROW4 36
ROW5 37
ERST 38
TCLK 39
VDD 40
TBUS3 41
GND 42
RXTX 43
TBUS2 44
SCLK 45
TBUS1 46
SIO 47
INT3 48
INT2 49
TBUS0 50
TEST 51
OFF_REQ 52
PRES 53
VP 54
CLK 55
GND 56
RST 57
VCC 58
AUX2 59 AUX1 60
I/O 61
VBUS 62
ON_OFF 63
VBAT 64
VPC 65
LIN 66
GND 67
SLUG 69
LED0
4
U4
73S1217F
1
TP1
VDD
D4
LED
R24
680
CLK and Vcc tracks should be
routed away from other Smart
card signals and should be
surrounded by GND.
C17
1000pF
1
6
2
7
3
8
4
9
5
P1
DB9_RS232
INT2
C22
0.1uF
CLK
Y1
32.768kHz
C23
0.1uF
C20
0.1uF
C33 should be as
close as possible
to pin 65
C21
0.1uF
ON_OFF
VDD
C8 USR3
USR5
C30, C31 and C32
should be as
close as possible
to VDD pins on U4
C19
0.1uF
VCC
C7
0.47uF
TXD
USR1
+5VDC
UnReg
1
2
TP6
D- 2
D+ 3
GND 4
VCC 1
GND 5
GND 6
J3
USB_CONN_4
C12
27pF
C30
0.1uF
C31
0.1uF
VDD
C32
0.1uF
12 34 5 6 78 910 11 12
TP2
HEADER 2 x 4
RXD
VBUS
R20 24
VDD
USR2
USR7
USR3
USR1
USR0
USR6
USR4
USR5
USR2
USR0
USR3
USR1
Install R6, R8, R11 and R12 for Plug
and Play operation, do not install
otherwise
R11 0
VDD
R6 0
R8 0
R12 0
C14
.1uF
C1+ 28
C1- 25
C2+ 1
C2- 3
T1IN 24
T2IN 23
T3IN 22
T4IN 19
T5IN 17
R1OUTBF 16
R1OUT 21
R2OUT 20
R3OUT 18
GND
2MBAUD
15
SHDNB
14 ENB
13 R3IN
11 R2IN
9R1IN
8
T1OUT
5
T2OUT
6
T3OUT
7
T4OUT
10
T5OUT
12
V-
4
V+
27
VCC 26
U3
MAX3237CAI
R22 100k
VDD
DPLUSDPLUSDPLUSDPLUSDPLUSDPLUSDPLUSDPLUSDPLUSDPLUSDPLUSDPLUSDPLUSDPLUSDPLUSDPLUSDPLUSDPLUSDPLUSDPLUSDPLUSDPLUSDPLUSDPLUSDPLUSDPLUSDPLUSDPLUSDPLUSDPLUSDPLUSDPLUSDPLUSDPLUSDPLUSDPLUS
VBUSVBUSVBUSVBUSVBUSVBUSVBUSVBUSVBUSVBUSVBUSVBUS
C33
10uF
C6
27p
Figure 6: 73S1217F Evaluation Board Lite Electrical Schematic

73S1217F Development Board User’s Guide UG_1217F_046
16 Rev. 1.2
4.3 PCB Layouts
Figure 7: 73S1217F Evaluation Board Lite Top View (Silkscreen)
Figure 8: 73S1217F Evaluation Board Lite Bottom View (Silkscreen)

UG_1217F_046 73S1217F Evaluation Board Lite User Guide
Rev. 1.2 17
Figure 9: 73S1217F Evaluation Board Lite Top Signal Layer
Figure 10: 73S1217F Evaluation Board Lite Middle Layer 1 – Ground Plane

73S1217F Development Board User’s Guide UG_1217F_046
18 Rev. 1.2
Figure 11: 73S1217F Evaluation Board Lite Middle Layer 2 – Supply Plane
Figure 12: 73S1217F Evaluation Board Lite Bottom Signal Layer

UG_1217F_046 73S1217F Evaluation Board Lite User Guide
Rev. 1.2 19
4.4 Bill of Materials
Table 3provides the bill of materials for the 73S1217F Evaluation Board Lite schematic provided in Figure 10.
Table 3: 73S1217F Evaluation Board Lite Bill of Materials
Item Qty. Reference Part PCB Footprint
Digi-key Part
Number
Part Number Manufacturer
1 3 C5,C6,C12,C16 27 pF 603 PCC270ACVCT-ND
ECJ-1VC1H270J Panasonic
2 1 C7 0.47 µF 603 PCC2275CT-ND ECJ-1VB1A474K Panasonic
3 1 C9 4.7 µF 603 PCC2396CT-ND ECJ-1VB0J475K Panasonic
4 7 C10,C11,C24,C25,C26,
C27,C28 22 pF 603 PCC220ACVCT-ND
ECJ-1VC1H220J Panasonic
5 1 C13 10 µF 3528-21 (EIA) 478-1672-1-ND TAJB106K010R AVX Corporation
6 10 C14,C19,C20,C21,C22,
C23,C29,C30,C31,C32 0.1 µF 603 445-1314-1-ND C1608X7R1H104K TDK Corporation
7 1 C17 1000 pF 603 PCC2151CT-ND ECJ-1VC1H102J Panasonic
8 1 C33 10 µF 805 PCC2225CT-ND ECJ-2FB0J106M Panasonic
9 4 D1,D4,D5,D6 LED 0805_DIODE 160-1414-1-ND LTST-C170FKT LITE-ON INC
10 4 G1,G2,G3,G4 MTHOLE MTHOLE
11 5 JP1,TP4,JP4,TP5,TP6 HEADER 5 X 1 PIN S1011E-36-ND PBC36SAAN Sullins
12 1 JP2 HEADER 5 X 2 PIN S2011E-36-ND PBC36DAAN Sullins
13 1 J1 Smart Card
Connector ITT/CCM02-2504 401-1715-ND CCM02-2504LFT ITT Industries
14 1 J2 Emulator IF RIBBON6513 A3210-ND 104068-1 AMP/Tyco
Electronics
15 1 J3 USB_CONN_4 USB ED90064-ND 897-43-004-90-
000000 Mill-Max
16 1 L1 10 µH 1210 490-4059-2-ND LQH32CN100K53L Murata
Electronics
17 1 PJ1 +5VDC SC237-ND RAPC712X Switchcraft
18 1 P1 DB9_RS232 A32075-ND 5745781-4 AMP/Tyco
Electronics
19 5 R1,R6,R8,R11,R12 0 603 P0.0GCT-ND ERJ-3GEY0R00V Panasonic
20 1 R2 1 MΩ603 P1.0MGCT-ND ERJ-3GEYJ106V Panasonic

73S1217F Evaluation Board Lite User Guide UG_1217F_046
20 Rev. 1.2
Item Qty. Reference Part PCB Footprint
Digi-key Part
Number
Part Number Manufacturer
21 2 R3,R22 100 kΩ603 P100KGCT-ND ERJ-3GEYJ104V Panasonic
22 1 R4 10 Ω603 P10GCT-ND ERJ-3GEYJ100V Panasonic
23 1 R5 10 kΩ603 P10KGCT-ND ERJ-3GEYJ103V Panasonic
24 8 R7,R9,R10,R13,R14,
R15,R16,R17 62 Ω603 P62GCT-ND ERJ-3GEYJ620V Panasonic
25 3 R18,R19,R24 680 Ω603 P680GCT-ND ERJ-3GEYJ681V Panasonic
26 1 R20,R21 24 Ω603 P24GCT-ND ERJ-3GEYJ240V Panasonic
27 2 R23,R25 200 kΩ603 P200KGCT-ND Panasonic
28 2 S1,S2 SW PB P8051SCT EVQ-PJX05M Panasonic
29 3 TP1,TP7,TP8 HEADER 2 x 4 S1011E-36-ND PBC36SAAN Sullins
30 1 TP2 HEADER 2 x 4 S2011E-36-ND PBC36DAAN Sullins
31 1 TP3 HEADER 8 S1011E-36-ND PBC36SAAN Sullins
32 1 U3 MAX3237CAI SOG.65M/28 MAX3237CAI+-ND MAX3237CAI+ Maxim
33 1 U4 73S1217F 68 QFN 73S1217F Teridian
34 1 Y1 32.768 kHz XTAL-CM200S 6513 XC1195CT-ND ECS-.327-12.5-17X-TR ECS
35 1 Y2 12.000 MHz XTAL/HC49US/.140H X1116-ND ECS-120-20-4XDN ECS