Texecom GSM MODULE User manual

GSM Module Installation Manual
GSM MODULE
Installation Manual
THANK YOU FOR VOTING TEXECOM

GSM Module Installation Manual
2INS227
Introduction
The GSM module can be connected to the Premier 48/88/168 control panels to provide
the following facilities:
• Report system events (alarms, arm, disarm etc.) via text messaging to mobile
telephones
• Remotely arm, disarm and obtain current status of the alarm system via text
messaging
• High-speed modem communication for upload/download
• Backup signalling path for Com300/2400 digital communicator
The GSM module is only supported on control panels fitted with software
version 3.0 or above.
The GSM module can only be used as a modem if the data service is
enabled by your network provider. Pay as you go tariffs generally do not
provide this feature.
GSM Module Parts and Layout


GSM Module Installation Manual
INS227 3
GSM-Com Connectors and Layout
Connector Description
CON 1 This 2.1mm power plug should be plugged into the power socket on the GSM
module.
CON 2 This RJ45 type connector should be plugged into the RJ45 Headset socket on
the GSM module.
CON 3 This 7-way Molex type connector should be plugged onto Com 2 on the
Premier48/88/168 control panel.
CON 4
This 5-way Molex type connector should be plugged onto the AUDIO port on
the Premier Com300/2400 communicator (this is only required if you want to
use the GSM Module as a backup for the Com300/2400).
Installation
1. Insert the GSM antenna in the SMB socket of the GSM module.
2. Connect the RJ45 connector of the GSM-Com (CON 2) to the Headset socket of
the GSM module.
3. Open the cover cap on the underside of the GSM module:

GSM Module Installation Manual
4 INS227
4. Turn the securing plate as far as it will go with the aid of the cover cap:
5. Flip the holder upwards. Slide the SIM card into the SIM card holder with the
contact surface facing down and the flattened side at the top left:
6. Press the holder down and secure it with the securing plate. Close the opening
with the cover cap.
The SIM card must be inserted before connecting the GSM module to the
power supply, and must not be removed until after the power supply to the
GSM module has been deactivated.
7. Attach the power cable (CON 1) of the GSM-Com to the GSM module.
8. Connect the 7-way molex of the GSM-Com to COM2 on the control panel. The
green power led on the GSM-Com and the orange led on the GSM module
should now be lit.
9. Connect the 5-way molex of the GSM-Com to the AUDIO port on the
Com300/2400 (if fitted).


GSM Module Installation Manual
INS227 5
Panel Configuration
Before attempting to use the GSM module it must be correctly configured as follows:
1. Enter “Engineers Programming” mode and select “UDL/Digi Options”, then
select “Com Port Setup”. Ensure Com Port 2 is programmed as “GSM Module”.
2. Now select the “Digi Options” menu and make sure that “Digi Option 1” is
programmed for “Digi is Enabled”.
3. Now select “Program Digi” and ensure the following options are programmed for
one of the ARC options:
a) Protocol: “SMS Messaging”.
b) Primary No: The number of the recipients mobile telephone.
c) Secondary No: Secondary mobile telephone number (if required).
d) Account No: Leave blank.
e) Dialling Attempts: Program as required.
f) Report Areas: Program as required.
g) Reports: Program as required.
h) Config.: Program as required.
4. Select the “Radio/SMS options” menu and scroll down until the display shows
the GSM signal level. Ensure that the level is between –10 and –95 dBm and the
Bit Error Rate (BER) is less than 6.
Using the SMS Control Commands
Control commands can be sent to the GSM module to allow remote control and
integration of the alarm system.
1. Select the send text message option on your mobile telephone.
2. Enter the telephone number of the GSM module.
3. Enter the text command, see SMS Control Commands.
4. Select send on your mobile telephone.
When using the SMS Control Commands shown in the table on the next page the
following should be noted:
???? = User code, this must proceed all commands.
[areas] = Areas 1 to 8 or A to P. If the areas are not specified then all areas will be
selected.
[s] = Send back status report
(zones) = List of zones, each zone must separated by a space e.g. 1 12 167 etc.
(outputs) = List of output, e.g. 1234 etc.
(message) = A maximum of 32 characters.

GSM Module Installation Manual
6 INS227
SMS Control Commands
Operation Command Example
Arm System ???? arm [areas][s] “5678 arm s” = arm all areas and report back
status.
Part Arm System ???? parm (1/2/3)[s] “5678 parm 1” = part arm 1 all areas (no status)
Disarm System ???? darm [areas][s] “5678 darm abcs” = disarm areas abc and report
back status.
Reset System ???? reset [areas] “5678 reset” = reset all areas
Omit Zone(s) ???? omit (zones) “5678 omit 1 5 12” = omit zones 1, 5 and 12
Unomit Zone(s) ???? uomit (zones) “5678 uomit 12” = reinstate zone 12
Turn Outputs On ???? op on (outputs)[s] “5678 op on 134” = turn PC outputs 1, 3 and 4 on.
Turn Outputs Off ???? op off (outputs)[s] “5678 op off 4s” = turn PC output 4 off and report
back status.
Send Message ???? mess (message) “5678 mess How Are You” = Displays How Are
You on all keypads.
System Status ???? status
“5678 status” =
Armed: (1 - 8 or A - P)
Alarm: (1 - 8 or A - P)
Output: (1 - 8)
Mains: (OK or Fault)
Battery: (OK or Fault)
Phone Line: (OK or Fault)
Output Status ???? status O
“5678 status O” =
Armed: (1 - 8 or A - P)
Alarm: (A - P)
Channels: (1 - 8)
Digi: (1 - 8)
Panel: (1 - 5)
Mains: (OK or Fault)
Battery: (OK or Fault)
Phone Line: (OK or Fault)
GSM/Radio-Pad
Status ???? status R
“5678 status R” =
Serial: ####### (only if Radio-Pad fitted)
NUA: ###### (only if Radio-Pad fitted)
FSS: ### (only if Radio-Pad fitted)
RSS: ### (only if Radio-Pad fitted)
BER: ### (only if Radio-Pad fitted)
CRC: ### (only if Radio-Pad fitted)
GSM-Signal: ###
GSM-BER: ###

GSM Module Installation Manual
INS227 7
What will be sent in the Text Message
The following information will be received in the text message:
3 W e s t e r n R o a d
12:45.58 01/12
Zone 003Alarm
The Detector in
the Lounge
Area:A.......
My Home
Up to 16 characters of text (this is the Printer Header)
Time and Date
Event Type
Zone/User name text
Area that caused the event
Name programmed into phone
Standards
The GSM-Com and GSM Module conform to European Union (EU) Low Voltage Directive
(LVD) 73/23/EEC (amended by 93/68/EEC) and Electro-Magnetic Compatibility (EMC)
Directive 89/336/EEC (amended by 92/31/EEC and 93/68/EEC).
The CE mark indicates that this product complies with the European requirements for
safety, health, environment and customer protection.
Notes

Texecom Limited, Bradwood Court, St. Crispin Way, Haslingden, Lancashire BB4
4PW, England.
Technical Support:
Tel: [phone]; Tel: [phone]; Fax: [phone]
INS227