Texecom INS656-3 User manual

INSTALLATION INSTRUCTIONS
Premier Elite Speech Module
INS656-3

INS656-3 2/13
Content
1.0 Introduction 3 ............................................................................................................................
2.0 Hardware Identification 3 ........................................................................................................
3.0 Specifications 12 ........................................................................................................................
4.0 Warranty 13 ................................................................................................................................

INS656-3 3/13
1.0 Introduction
The Premier Elite Speech Module provides four recordable 10 second audio
messages, each message is assigned to a Digi Channel, which in turn can be
triggered from one of the many output functions of the control panel. A COM2400
must be installed to enable the Premier Elite Speech Module, it will not function
with a COM300. Only the first four Digi Channels are used by the Premier Elite
Speech Module. The Premier Elite Speech Module is supported by the following
Texecom control panels:
Premier Elite all models factory built V3 and later, all models fitted with a
DTMF decoder.
N If the Speech Module is fitted to a V3 panel that does not have the DTMF
decoder chip fitted, it may not be possible to acknowledge the received calls. This
will result in repeated calls until all programmed dial attempts have been used.
2.0 Hardware Identification
The DTMF chip is located below the
Barcode label and is identified with a
green dot.

INS656-3 4/13
The DTMF chip is located just below the digi pins and is identified with a
green dot.
The DTMF chip is located to the left of the main processor and is identified with a green dot.

INS656-3 5/13
PCB Layout and Connections
The figure below shows the PCB layout of the Premier Elite Speech Module.

INS656-3 6/13

INS656-3 7/13
Figure 2 Premier Elite Speech Module Connected to Expansion Port on PCB
Premier Elite Speech Module Installation
To install the Premier Elite Speech Module proceed as follows:
Ensure that all power is removed from the control panel before connecting the
Premier Elite Speech Module.
Plug the Premier Elite Speech Module (see Figure 2) onto the 7 way Expansion
Port of the control panel.
Plug the COM2400 onto the onboard digi pins, and connect to a telephone line.
When using an RJ11 plug, this should be connected before the COM2400 is fitted in
place.
Re-apply power to the system and proceed to the next section.
Premier Elite Speech Module Locations
Use the self-adhesive mounting posts to locate the Speech Module as shown.
Premier Elite Small Polymer Housing (e.g. Live front ) mount to the rear of the
housing

INS656-3 8/13
Premier Elite Large Polymer Housing (e.g. 24 & -W panels) mount to the inner
wall of the housing
Premier Elite Metal Housing (e.g. 48.88 & 168) mount inside the top of the
housing.

INS656-3 9/13
Recording Messages
The Premier Elite Speech Module can store four 10-second audio messages.
Message 1 is allocated to channel 1 and message 2 is allocated to channel 2 etc.
To record a message proceed as follows:
Press and hold the [RECORD] button, then press and hold either [REC1] for
message 1 or [REC2] for message 2 [REC3] for message 3 or [REC4] for
message 4
Speak clearly into the microphone to record your message. During the
recording process, the record indicator will illuminate.
To stop the recording process, release the record buttons. The recording

INS656-3 10/13
process will automatically end after 10 seconds and the record indicator will
go out.
Repeat steps 1 to 3 for other messages, if required.
Programming the Control Panel
The control panel will then need to be programmed correctly in order for the
Premier Elite Speech Module to function as expected:
Program Onboard Com2400 & Expansion Port
Enter the engineer code ????
Press 7 then y/y (UDL/Digi Options).
Press 8 then y/y for (Com Port Setup/Onboard Digicom).
Press n/n then 2 to select COM2400
Press y/y
Press 5 (Expansion Port).then n/n
Press 6 (Speech Module) then y/y
Digi Enabled & Dial All Numbers
If you have more than one communication device connected to the control panel,
Dial All Numbers MUST be enabled; continuing from the previous
Press N/N then 4 then y/y (Digi Options)
Press n/n
Press 1 Digi is Enabled (E shown on Screen)
Press 6 Dial All Numbers (A shown on screen)
Press y/y
Program ARC's
Press N/N then 3 then y/y (Program Digi)
Press y/y
Using the Scroll key select Which ARC you wish to use
Press n/n and scroll to change the ARC protocol to Speech Module

INS656-3 11/13
Press y/y twice then n/n
In the Pri. Tel No: screen enter the telephone number you wish to
dial.
Press y/y
In the Sec. Tel No: enter an additional telephone number if required.
Press y/y
Program any additional ARC requirements to add additional telephone numbers.
N Inserting an * after the number will force dialling of the next number even if
the message is acknowledged.
N The reporting options for the Premier Elite Speech Module are fixed and
should not be changed. All types of alarm programmed for channels 1-4 will be
reported for the selected Areas, however Restores will not.
Programming Digi Channels
The default Digi Channels on the panels are programmed as follows:
If you need to change the defaults proceed as follows:
Enter the engineer code ????
Press 6 then y/y (System Outputs).
Press 2 then y/y for (Digi Channels).
Press n/n then use the U to select the output type
Press y/y then use the U to select the output
Press y/y then select the Areas

INS656-3 12/13
Press y/y to accept
Use the U to select the next Output and repeat the previous steps.
N Only channels 1-4 are used by the Premier Elite Speech Module.
Testing the Premier Elite Speech Module
The procedure below shows how to perform a simple operational test for the
Premier Elite Speech Module
Press N/N twice then 7 y/y (UDL/Digi Options)
Pressy/y then 1 y/y (Start Test Call)
Press 0 to start the test call. All communication devices on the system will
carry out a test call.
If you have a telephone on the same line as the control panel, you can pick it up
and listen to the message.
During the test call you may press 1,2,3 or 4 to switch between
playing messages 1 2 3 & 4.
The person listening to the message on their telephone can acknowledge the call
by pressing the [#] key. This will cause the panel to hang-up the call. If not
acknowledged it will continue to dial all of the programmed numbers.
3.0 Specifications
Supply Voltage: 9 – 16VDC
Current Consumption (Standby): 1mA
Current Consumption (Active): 7mA
Messages/Channels: 4
Message Length: 10 Seconds each
Dimensions: 52mm x 30mm x 10mm
Packed Weight: 25g
Operating Temperature: -10°C (+14°F) to +50°C (+122°F)
Storage Temperature: -20°C (-4°F) to +60°C (+140°F)
Maximum Humidity: 95% non-condensing

INS656-3 13/13
Texecom declares that this product complies with the requirements of the
following directives:
• 2004/108/EC EMC Directive
• 2006/95/EC LVD Directive
• 2011/65/EU RoHS Directive
The product therefore meets all the requirements to enable it to be CE marked.
WEEE Directive: 2012/19/EU (WEEE directive): Products marked with this symbol
cannot be disposed of as unsorted municipal waste in the European Union. For
proper recycling, return this product to your local supplier upon the purchase of
equivalent new equipment, or dispose of it at designated collection points. For
more information see: www.recyclethis.info.
This product is suitable for use in systems designed to comply with EN 50131-1 &
EN50131-3 at Grade 2 and Environmental Class II.
4.0 Warranty
All Texecom products are designed for reliable, trouble-free operation. Quality is
carefully monitored by extensive computerised testing. As a result, the Premier
Elite Speech Module is covered by a two-year warranty against defects in material
or workmanship.