Textron tx2000 User manual

Service Manual
Battery Powered Tool

3
Contents
Annual Service
Service Kit 4
Before Dismantling 4
Repairs & Major Service
Moulded Body Assembly 5
Pump Assembly 6
Motor, Gearbox, Electrical Assembly 6
Head Assembly 7
Trigger Mechanism 8
Housing Assembly 8
Reservoir Assembly 9
Troubleshooting 9
Assembly Diagram & Base Tool 10
Parts List 11
This manual is only for use by TFS authorized distributors and repair centres.
IMPORTANT: The warranty is invalidated if the installation tool is not identified
with a relevant serial number label. The label is positioned internally, at the base
of the handle, on the left moulding, 41. When replacing the moulded body a new
label, 83, must be inserted and marked by hand with the tool's original serial
number.
CONTENTS

4
Annual Service
•Every 500,000 cycles the tool should be completely dismantled and new components should be used
where worn, damaged or recommended. All ‘O’ rings and seals should be renewed and lubricated with
MolyKote 111 grease before assembling.
•For an easy complete service, Textron Fastening Systems offer a complete service kit as detailed below.
Spanners are specified in inches and across flats unless otherwise stated
ANNUAL/500,000 CYCLE SERVICE
Service Kit: 71600-99990
Part No. Description
07900-00006 Spatular
07900-00008 7/16 x 1/2Spanner
07900-00012 9/16 x 5/8Spanner
07900-00015 5/8x 11/16 Spanner
07900-00243 Screwdriver - Small
07900-00333 Screwdriver - Medium
07900-00469 2.5mm Allen Key
07900-00737 Piston Seal Sleeve
07900-00738 Piston Seal Tool
07900-00739 Piston Bullet
07900-00740 Cylinder Collar
07900-00741 Guide Tube
07900-00742 Insertion Rod
07900-00743 End Cap Assembly Tool
Part No. Description
07900-00748 Threaded Sleeve Bullet
07900-00747 Valve Seat Tool
07900-00749 Threaded Sleeve Tool
07900-00750 Valve Needle Sleeve
07900-00751 3mm Allen Key - Short Reach
07900-00753 Circlip Pliers - Small
07900-00754 Priming Pump
07900-00755 Grease - MolyKote 111 - 100g tube
07900-00756 Loctite®243 Threadlocker
07900-00757 Scalpel
07900-00760 Pozi Screwdriver
07900-00788 Service Kit Storage Case
07900-00768 Reservoir Bullet
07900-00769 Trigger Tool
07992-00020 Grease - Moly-Lithium
Before dismantling:
•Disconnect the battery before any servicing or dismantling is attempted, unless specifically instructed otherwise.
•Care must be taken at all times to ensure that conditions are clean so that no foreign matter enters the tool or serious
damage may result.
•Empty the oil from the tool following the first three steps of the priming procedure. Refer to the priming procedure on pages 14
and 15 of the Instruction Manual.
•Remove the nose equipment.
For a complete service of the tool, we advise that you proceed with dismantling of sub-assemblies in the order shown on
page 5. After dismantling the tool we recommend that you replace all seals.
On reassembly it is essential to prime the tool and fit an appropriate nose assembly prior to operating.

5
Repairs & Major Service
IMPORTANT: The warranty is invalidated if the installation tool is not identified with a relevant serial number label.
The label is positioned internally, at the base of the handle, on the left moulding, 41. When replacing the moulded
body a new label, 83, must be inserted and marked by hand with the tool's original serial number.
The moulded body assembly includes items 1, 2, 33, 41 to 45, 47, 48, 53, 54, 81 and 83. These parts are only available as
a complete Body Moulding Assembly Kit (part number 71600-99600), unless the individual part numbers are provided in the
parts list.
•Remove and discard label 42 from the right moulding 43 to reveal the hidden screw.
•Remove the nose tip spanner 53 and two nose tips from the moulded body.
•Place the tool on its side and using the pozi screwdriver unscrew all eight pozi screws 45 in the moulded body.
•Remove the right moulding 43 leaving the main internal mechanism within the left moulding 41 as shown on page 10.
•Remove the vent screen 54, battery retainer spring 47 and dowel pin 48 from the left moulding 41.
•Before removing the main internal mechanism ensure that the electrical control circuit 5and the reservoir 73 are released
from the mounting points within the moulding.
•Holding the tool by the motor and gearbox assembly 3remove the main internal mechanism from the moulding.
Assemble in reverse order to dismantling noting the following points:
•Place the main internal mechanism into the left moulding 41, first ensuring that the electrical control circuit 5and the
reservoir 73 are correctly placed within the mounting positions provided. The circuit board must be positioned so that the
heat sink is facing forward and the black and blue wires are at the top. The contact holder 4must be positioned with the
positive symbol in the left moulding 41 as shown in the diagram below.
•The contact holder is designed to enable correct orientation in the mouldings. Care must be taken to ensure that the raised
portion on the right moulding 43 fits within the indent on the negative side of the contact holder 4.
•When replacing the right moulding 43 take care to ensure that no wires are trapped and correct alignment with the electrical
control circuit 5and the vent screen 54 are achieved.
•When the moulded body is fully assembled with all eight pozi screws 45, insert new case label 42 on the right moulding 43.
IMPORTANT: Correct orientation of the contact holder 4 must be achieved when assembling into mouldings 41 and
43. Incorrect assembly will cause short circuit and failure of electrical control circuit.
MOULDED BODY ASSEMBLY
Left Hand
Moulding
Contact Holder
Recessed
Edge

6
Repairs & Major Service
PUMP ASSEMBLY
The pump assembly includes items 29, 35, 36, 37, 49, 51 and one of the following plunger seal combinations, either seals
(37 and 50 2 off) or (37, 84 and 85). These parts are only available fully assembled as a complete Pump Assembly Kit (part
number 71600-99601), unless the individual part numbers are provided in the parts list.
•Completely remove the main internal mechanism from the left and right mouldings 41, 43, as described on page 5.
•To gain access to the pump attachment screws 29 the trigger assembly, items 34, 40, must be removed. Using the circlip
pliers remove one circlip 67 from pin 66. Push the pin out allowing the trigger lever 34 and trigger button 40 to be removed.
•Hold the main internal mechanism and pump block 51 securely in position and using the 3 mm allen key remove the four
attachment screws 29. Remove the complete pump assembly from the housing 24. Care must be taken when removing
the pump assembly as the plunger 36 will be spring loaded.
•Remove the plunger 36 and spring 35 from the pump block 51 taking care not to damage the seals, plunger surface and
the pump block bore.
•Remove ‘O’ ring 49 from housing 24 and discard.
Assemble in reverse order to dismantling noting the following points:
•Clean the plunger 36 and apply a small amount of Molykote 111 grease to the seals using the spatula.
•Clean the pump block 51 bore and then lubricate with Molykote 111 grease using the spatula.
•Place spring 35 over the sealed plunger, align the end of the plunger with the pump block 51 bore and push into place
until the seals are no longer visible. When inserting the plunger take care not to damage the seals on the rim of the pump
block bore.
•Apply a light film of Loctite®243 threadlocker to all four screws 29.
•Attach the pump assembly onto the housing 24 as before using four screws 29 and the 3 mm allen key.
•Finally assemble the trigger assembly, items 34, 40, and pin 66 in reverse order to dismantling.
The motor, gearbox and electrical assembly includes items 3, 4, 5, 28, 38 and 52. These parts are only available as a
complete assembly (part number 71600-99602), unless the individual part numbers are provided in the parts list.
•Completely remove the main internal mechanism from the left and right mouldings 41, 43, as described on page 5.
•Remove the ‘pump assembly’ as described above.
•Using the small screwdriver remove the two screws 28 that retain the micro-switch to the switch bracket 27.
•Using the 3 mm allen key remove all three screws 38 and washers 52 attaching the gearbox to the housing 24.
•Remove the complete motor, gearbox and electrical assembly 3,4 and 5from the housing 24.
Assemble in reverse order of dismantling noting the following points:
•Ensure that the motor and gearbox assembly, when connected to the housing 24, is orientated so that the groove in the
gearbox mounting plate is at the top.
•Apply Loctite®243 threadlocker to all three screws 38.
•DO NOT USE UNDUE FORCE when inserting the three screws 38 into the housing 24.
MOTOR, GEARBOX AND ELECTRICAL ASSEMBLY

7
Repairs & Major Service
HEAD ASSEMBLY
The head assembly consists of three assembly kits, Cylinder Assembly Kit (part number 71600-99603), Piston Assembly Kit
(part number 71600-99604) and Head Seal Kit (part number 71600-99605) containing items 6to 18, 21, 22, 23, 30 and
32. These parts are only available as complete kits unless the individual part numbers are provided in the parts list.
•Completely remove the main internal mechanism from the left and right mouldings 41, 43, as described on page 5.
•Remove the complete motor, gearbox and electrical assembly 3,4 and 5as described on page 6.
•Unscrew locknut 31 and jaw spreader housing 20 from the piston 18.
•Using the 3 mm and 2.5 mm allen keys remove screws 11, 23, 30, clamping the cylinder 32 to the housing 24.
•Remove the head assembly from the housing. Remove ‘O’ ring 56 from the housing and discard.
•Grip the head assembly in a vice using soft jaws to avoid damage.
•Using the end cap assembly tool unscrew and remove the cylinder cap assembly, items 6, 7, 8, 9from the rear of the
cylinder 32. Care must be taken as the cylinder cap 7will be spring loaded.
•Remove and discard the spring 10 from inside the cylinder 32.
•Push the piston 18 to the rear and out of the cylinder 32 taking care not to damage the cylinder bore.
•Using the medium screwdriver enter the rear of the cylinder 32, lever the rod seal 15 from the groove and cut through
with a scalpel taking care not to damage the cylinder bore or the seal groove. Using the spatula push the rod seal,
followed by bearing ring 16 and ‘O’ ring 17 to the rear and out of the cylinder. If at any time the cylinder bore or seal
groove become damaged the cylinder must be replaced.
•Using a scalpel cut through and remove the piston seal 14 from the piston 18. Then remove bearing ring 13 and ‘O’ ring
12. Take care not to damage the piston when cutting the seal.
Assemble in reverse order to dismantling noting the following points:
•Clean all components before assembling.
•To aid assembly of seals apply a light coating of Molykote 111 grease to both the seals and the assembly tools.
•Lubricate the cylinder 32 bore and seal grooves with Molykote 111 grease. Insert the bearing ring 16 into place within
cylinder. With the aid of the spatula insert the ‘O’ ring 17. Place the rod seal 15 onto the insertion rod ensuring correct
orientation. Push the guide tube into the cylinder bore and push the insertion rod with the seal into place through the guide
tube ensuring seal is correctly seated. Pull the insertion rod out then the guide tube.
•Lubricate the piston 18 shaft and seal grooves with Molykote 111 grease and fit ‘O’ ring 12 and bearing ring 13. Place
the piston seal sleeve over the piston shaft, then slide the piston seal 14 over the sleeve and into position using the piston
seal tool ensuring correct orientation.
•Insert the cylinder collar into the back of the cylinder 32. Screw the piston bullet onto the piston 18 and push the piston with
the seals through the cylinder collar as far as it will go. Unscrew the bullet off the piston and remove the cylinder collar.
•Apply a light coating of Moly-lithium grease to the surface and ends of the spring 10 before inserting onto the piston 18
within the cylinder.
•Screw the cylinder cap assembly, items 6, 7, 8, 9, into the cylinder 32 using the ‘T’-bar and end cap assembly tool.
•Insert ‘O’ ring 56 into the housing and lubricate with Molykote 111 grease.
•Fit the head assembly to the housing 24 using the three screws 11, 23, 30, coated with Loctite®243 threadlocker.

8
Repairs & Major Service
The trigger mechanism includes items 34, 40, 58 to 69. These parts are only available as a complete Trigger Mechanism
Kit (part number 71600-99606), unless the individual part numbers are provided in the parts list.
•Completely remove the main internal mechanism from the left and right mouldings 41, 43, as described on page 5.
•Using the circlip pliers remove one circlip 67 from pin 66. Push the pin out allowing the trigger lever 34 and trigger button
40 to be removed.
•Using the circlip pliers carefully remove circlip 68 from the valve needle 61, followed by shim 69, trigger plate 65 and
spring 60. Discard the spring 60.
•Using the threaded sleeve tool unscrew and remove the threaded sleeve 64 from the housing 24. Remove ‘O’ ring 62
from the threaded sleeve and discard.
•Remove the valve needle 61 from the housing 24, then remove and discard the spring 60 from the valve needle 61. Using
a scalpel cut ‘O’ ring 63 from the valve needle taking care not to damage the seal groove.
•Using the valve seat tool unscrew the valve seat 59 and remove from the housing 24. Remove bonded seal 58 from valve
seat and discard.
Assemble in reverse order to dismantling noting the following points:
•Clean all components before assembling.
•Lubricate valve needle 61 shaft and seal groove with Molykote 111 grease and place the valve needle tool over the end of
the valve needle 61. Slide ‘O’ ring 63 over the valve needle sleeve and into the seal groove on valve needle. Remove the
valve needle sleeve from the valve needle.
•Lubricate threaded sleeve 64 with Molykote 111 grease and place the threaded sleeve bullet over the end of the threaded
sleeve. Slide ‘O’ ring 62 over the threaded sleeve bullet and into the seal groove on threaded sleeve. Remove bullet from
threaded sleeve.
•DO NOT USE UNDUE FORCE when inserting the valve seat 59 into the housing 24.
•When fitting threaded sleeve 64 into housing 24, ensure the component is screwed fully down until stopping against the
valve seat 59.
•When fitting trigger plate 65, ensure correct orientation is achieved.
•Using the trigger tool and pin 66 in place of the trigger lever 34, fully compress the trigger plate 65 into the threaded
sleeve 64 against the spring 60. The end of the valve needle 61 will become exposed. Place the shim 69 over the valve
needle and then insert the circlip 68 into the groove using the circlip pliers. Release and remove the trigger tool.
TRIGGER MECHANISM
HOUSING ASSEMBLY
The housing assembly consists of items 24 to 27, 38 and 75, all of which are available as individual parts. The assembly
also contains items 39, 55,56,57,70 and 76. These parts are only available as a complete Housing Hydraulic Kit (part
number 71600-99607).
•Completely remove the main internal mechanism from the left and right mouldings 41, 43, as described on page 5.
•Do not remove screws 25, 38, from the housing 24.
•Using medium screwdriver unscrew seal screw 75 from housing 24. Remove ‘O’ ring 76 from seal screw.
•Using medium screwdriver unscrew inlet check valve 70 from housing 24.
•In order to remove outlet check valve 55 the head assembly must be removed as described on page 7.
•Using medium screwdriver unscrew outlet check valve 55 from housing 24. Remove ‘O’ ring 57 from outlet check valve
and discard.
•Assemble in reverse order to dismantling.

9
Repairs & Major Service
The reservoir assembly includes items 21, 22, 25,78,82 and 71 to 74. These parts are only available as a complete
Reservoir Assembly Kit (part number 71600-99608), unless the individual part numbers are provided in the parts list.
•Completely remove the main internal mechanism from the left and right mouldings 41, 43, as described on page 5.
•Using the 3 mm allen key remove screw 21 and bonded seal 22 from reservoir 73.
•Using the spatular remove 'O' ring 72 from reservoir 73 and discard.
•Remove reservoir 73 from reservoir adapter 74.
•Using the 2.5 mm allen key, remove screw 25 attaching reservoir adapter 74 to housing 24.
•Remove reservoir adapter 74 from housing 24.
•Remove 'O' ring 71 from reservoir adapter 74 and discard.
•Do not remove the filter 78, or the 'O' ring 82, from the reservoir adapter 74 unless damaged. If removed discard both
items.
Assemble in reverse order to dismantling noting the following points:
•Lubricate both ‘O’ ring 71 and seal groove on reservoir adapter. Place ‘O’ ring 71 in reservoir adapter 74.
•Using 2.5 mm allen key and screw 25 fit reservoir adapter 74 to housing noting correct orientation with the holes.
•Slide open end of reservoir 73 over reservoir adapter 74 and into position within the groove.
•Place the reservoir bullet over the closed end of reservoir 73. Slide ‘O’ ring 72 completely over the bullet until it falls into
place around the end of the reservoir 73, holding it in securely around the reservoir adapter 74.
•Ensure that the reservoir 73 is correctly positioned on the reservoir adapter 74, so that the flat face on the metal part of
the reservoir is at the top.
IMPORTANT: Check the tool against daily and weekly servicing.
Priming is ALWAYS necessary after the tool has been dismantled and prior to operating.
RESERVOIR ASSEMBLY
TROUBLESHOOTING
Fastener fails to break Trigger mechanism springs worn Replace trigger mechanism 8
Jaws will not release Damaged spring in head assembly Fit new spring 7
broken stem of fastener
Tool fails to operate - Pump plunger jammed Replace pump spring 6
motor operational:
if head piston static Inlet check valve faulty Replace inlet check valve 8
if head piston pulsing Outlet check valve faulty Replace outlet check valve 8
Tool fails to operate - Motor or gearbox failure Test and replace any defective equipment 6
motor not operational Electrical control circuit failure Test and replace any defective equipment 6
SYMPTOM POSSIBLE CAUSE REMEDY PAGE REF.

10
General Assembly of Base Tool 71600-02000
A
4
123
567
89 10 11 12 13 14 15 16 17 18 19 20 21 22
23
24
25 5Ref
26
27
31 32
33
34
35
36
37
38
39
4
42, 43 Right Hand
41, 44 Left Hand
45
46
50
49
48
47
5
38
51
52
VIEW ON A
ENLARGED VIEW OF TRIGGER MECHANISM
INTERNAL MECHANISM
(EXCLUDING MOULDINGS)
ALTERNATIVE PUMP ARRANGEMENT
53
54
55 56 57 58
59 60
60
61 62 63
64
65 66 67
68
69
70 25
71 72 73
76 75 74 82
29
84
30
28
81
40
21
22
78
85
37

11
Parts List
45 07001-00652 Pozi screw 8
9
50
46 07007-01954 Battery 1 ✔1 47 71600-02022 Battery retainer spring 1
9
10
48 07007-01957 Dowel pin 1
9
50
49 07003-00353 O-ring 1
2
50
50 see note
2
O-ring 2
2
51 see note
2
Pump block 1
2
52 07002-00156 Steel washer 3
1
50
53 71600-02024 Nose tip spanner 1
9
10
54 see note
9
Vent screen 1
9
55 see note
5
Outlet check valve 1
5
56 see note
5
&
8
O-ring (housing) 1
58
57 see note
5
O-ring for item 55 1
5
58 see note
4
Bonded seal 1
4
59 see note
4
Valve seat 1
4
60 see note
4
Compression spring 2
4
61 see note
4
Valve needle 1
4
62 see note
4
O-ring 1
4
63 see note
4
O-ring 1
4
64 see note
4
Threaded sleeve 1
4
65 see note
4
Trigger plate 1
4
66 see note
4
Pin 1
4
67 07004-00104 Circlip 2
4
50
68 07004-00103 Circlip 1
4
50
69 see note
4
Steel shim washer 1
4
70 see note
5
Inlet check valve 1
5
71 see note
3
O-ring 1
3
72 see note
3
O-ring 1
3
73 see note
3
Reservoir 1
3
74 see note
3
Reservoir adapter 1
3
75 71600-02013 Seal screw 1 ✔1 76 see note
5
O-ring 1
5
77 07007-01965 Battery charger - 220/240V~50Hz (UK) 1 ✔1
07007-01966 Battery charger - 220/240V~50Hz (Europe) 1 ✔1 07007-01967 Battery charger - 220/240V~50Hz (Australia) 1 ✔1 07007-01968 Battery charger - 110V~60Hz (USA, Canada) 1 ✔1 07007-01969 Battery charger - 100V~50/60Hz (Japan) 1 ✔1
78 see note
3
Filter 1
3
79 07007-01960 Storage case 1 ✔1 80 07900-00759 Tool Instruction Manual - UK version 1 ✔1 81 see note
9
Collector lid buffer 1
9
82 see note
3
'O' Ring 1
3
83 71600-02035 Blank serial number label 1
9
50
84 see note
2
Energised PTFE seal 1
2
85 see note
2
Energised lip leal 1
2
1 71600-02004 Lid torsion spring 1
9
50
2 see note
9
Collector lid 1
9
3 see note
1
Motor & gearbox assembly 1
1
4 see note
1
Contact holder 1
1
5 see note
1
Electrical control circuit 1
1
6 07004-00102 Circlip 1
7
50
7 see note
7
Cylinder cap 1
7
8 see note
7
Piston sleeve 1
7
9 see note
8
O-ring 1
8
10 see note
7
Compression spring 1
7
11 07001-00650 Socket csk head screw 1
6
50
12 see note
8
O-ring (piston) 1
8
13 see note
8
Piston bearing ring 1
8
14 see note
8
Piston seal 1
8
15 see note
8
Rod seal 1
8
16 see note
8
Cylinder bearing ring 1
8
17 see note
8
O-ring (cylinder) 1
8
18 see note
7
Piston 1
7
19 07003-00277 O-ring 1 ✔50 20 71210-02101 Jaw spreader housing 1 ✔1 21 07001-00654 Button head screw 2
36
50
22 07003-00194 Bonded seal 2
36
50
23 07001-00646 Socket cap head screw 1
6
50
24 71600-02009 Housing 1 ✔1 25 07001-00647 Socket cap head screw 2
3
50
26 07002-00155 Steel washer 1 ✔50 27 71600-02014 Switch bracket 1 ✔10 28 07001-00648 Slotted cheese head screw 2
1
50
29 07001-00651 Socket cap head screw 4
2
50
30 07001-00645 Socket cap head screw 1
6
50
31 71600-02026 Locknut 1 ✔10 32 see note
6
Cylinder 1
6
33 see note
9
Nose tip holder 1
9
34 see note
4
Trigger lever 1
4
35 see note
2
Compression spring 1
2
36 see note
2
Plunger 1
2
37 see note
2
O-ring 1
2
38 07001-00649 Socket cap head screw 4
1
50
39 see note
5
Bonded seal 1
5
40 see note
4
Trigger button 1
4
41 see note
9
Left moulding 1
9
42 71600-02028 Case label RH 2
9
10
43 see note
9
Right moulding 1
9
44 71600-02027 Case label LH 1
9
10
ITEM PART Nº DESCRIPTION QTY SPARES ITEM PART Nº DESCRIPTION QTY SPARES
ORDER QTYORDER QTY
Note 1
Motor, Gearbox and Electrical Assembly (part number 71600-99602). These items are only available as a complete assembly unless individual part numbers are given, where the minimum order quantity shall apply.
2
Pump Assembly Kit (part number 71600-99601). These items are only available as a complete assembly unless individual part numbers are given, where the minimum order quantity shall apply.
3
Reservoir Assembly Kit (part number 71600-99608). These items are only available as a complete assembly kit unless individual part numbers are given, where the minimum order quantity shall apply.
4
Trigger Mechanism Kit (part number 71600-99606). These items are only available as a complete assembly kit unless individual part numbers are given, where the minimum order quantity shall apply.
5
Housing Hydraulic Kit (part number 71600-99607). These items are only available as a complete kit.
6
Cylinder Assembly Kit (part number 71600-99603). These items are only available as a complete assembly kit unless individual part numbers are given, where the minimum order quantity shall apply.
7
Piston Assembly Kit (part number 71600-99604). These items are only available as a complete assembly kit unless individual part numbers are given, where the minimum order quantity shall apply.
8
Head Seal Kit (part number 71600-99605). These items are only available as a complete assembly kit unless individual part numbers are given, where the minimum order quantity shall apply.
9
Body Moulding Assembly Kit (part number 71600-99600). These items are only available as a complete assembly kit unless individual part numbers are given, where the minimum order quantity shall apply.
✔These items are available as individual spares subject to the minimum order quantity.

© TEXTRON FASTENING SYSTEMS 200007900-00760 GB/ JANUARY 2002
AUSTRALIA
Textron Fastening Systems Pty Ltd
891 Wellington Road
Rowville
Victoria 3178
Tel: [phone]
Fax: [phone]
AUSTRIA
Textron Verbindungselemente GmbH
Industriestrasse B-13 Halle 2
A-2345 Brunn/Gebirge
Tel: [phone]
Fax: [phone]
CANADA
Avdel Division of Textron Canada Ltd
87 Disco Road
Rexdale
Ontario M9W 1M3
Tel: [phone]
Fax: [phone]
CHINA
Textron Fastening Systems China Ltd
Room 1708 Nanyang Plaza
57 Hung To Road
Kwun Tong
Kowloon
Hong Kong
Tel: [phone]
Fax: [phone]
FRANCE
Textron Industries S.A.
33 bis, rue des Ardennes
BP4, 75921 Paris Cédex 19
Tel: [phone]
Fax: [phone]
GERMANY
Textron Verbindungstechnik GmbH
Klusriede 24
D - 30851 Langenhagen
Tel: [phone]
Fax: [phone]
ITALY
Textron Sistemi di Fissaggio SRL
Via Manin 350-21
It- 20099 Sesto San Giovanni
Milano
Tel: [phone]
Fax: [phone]
JAPAN
Avdel Kabushiki Kaisha
7F, New Erimo Building,
2-2-1, Senba Nishi,
Mino, Osaka 562-0036
Tel: [phone]
Fax: [phone]
SOUTH KOREA
Avdel Korea Limited
Sam Young Building
1486-2 Seo Cho-Dong
Seo Cho-Ku
Seoul
Tel: [phone]
Fax: [phone]
SPAIN
Textron Sistemas de Fijación S.A.
c/ Puerto de la Morcuera, s/n
Poligono Industrial Prado Overa
Autovia Madrid Toledo Km 7.8
Es - 28916 Leganes (Madrid)
Tel: [phone]
Fax: [phone]
UNITED KINGDOM
Textron Fastening Systems Ltd
Mundells
Welwyn Garden City
Hertfordshire
AL7 1EZ
Tel: [phone]
Fax: [phone]
USA
Avdel Cherry Textron Inc.
614 NC Highway 200 South
Stanfield, North Carolina 28163
Tel: [phone]
Fax: [phone]
Textron Fastening Systems
Commercial Solutions HQ
516 Eighteenth Avenue
Rockford, Illinois 61104
Tel: [phone]
Fax: [phone]