Theben PlanoSpot 360 DALI-2 S DE Series User manual

2020-04-27_307458
Manual
DALI-2 presence sensor
PlanoSpot 360 DALI-2 S DE

PlanoSpot 360 DALI-2 S DE manual 2
Contents
1General 3
1.1 Safety information 3
1.2 Proper use 3
1.3 Explanation of terms 3
2Function description 4
2.1 Overview of available instances 4
3Technical data 5
4Product characteristics 6
4.1 Usage 6
4.2 Functionality 6
4.3 Dimensions 7
4.4 Detection area 8
4.5 Infrared receiver 9
4.6 Display/visualisation 9
5Connection 11
6Installation 12
6.1 Ceiling installation 12
7Operation 13
7.1 Settings via remote control 13
7.2 Settings via the DALI bus 18
7.3 Status messages via the DALI bus 18
8Light measurement 19
8.1 Light measurement 19
8.2 Determining a value via the DALI bus 20
9Operating modes 21
9.1 Memory bank 2 – occupancy sensor 21
9.2 Memory bank 3–6 – light sensors 21
9.3 Memory bank 7–11 – button instance 22
9.4 Start-up behaviour 24
9.5 Addressing 24
9.6 Presence 24
9.7 Brightness 24
9.8 Button function 25
10 Accessories 27
11 Contact 29

PlanoSpot 360 DALI-2 S DE manual 3
1General
1.1 Safety information
ATTENTION
Installation should only be carried out by a qualified electrician!
1.2 Proper use
The PlanoSpot 360 DALI-2 S is intended for indoor installation. It serves as a DALI-2 input
device and transmits the collected sensor data to the multi-master application controller.
The PlanoSpot 360 DALI-2 S is exclusively intended for use as contractually agreed between the
manufacturer and the user. Any other use is considered to be unacceptable. The manufacturer
does not accept liability for any resulting damages.
1.3 Explanation of terms
There is a difference between motion detectors and presence detectors. Motion detectors can
only detect large movements. Presence detectors, on the other hand, can detect even the
smallest of movements – those made while seated, for example. DALI-2 sensors can detect
both large and small movements and are therefore referred to as presence sensors. However,
the implementation of the motion detection function in line with IEC 62386 Part 303 is based on
the concept of a "movement based sensor".
This manual only describes operating mode 0x00.

PlanoSpot 360 DALI-2 S DE manual 4
2Function description
The PlanoSpot 360 DALI-2 S devices are integrated into a higher-level system. Thanks to the
DALI-2 standard, a multi-master application controller from any manufacturer may be used.
This controller must support IEC 62386 Parts 101/103 and optionally – in order to use the
information regarding presence as well as brightness – Parts 303/304.
The PlanoSpot 360 DALI-2 S devices and other DALI components are connected to the DALI line.
The DALI supply is provided by the higher-level system. The assignment of the short addresses
and the selection of the required instances for the PlanoSpot 360 DALI-2 S devices are carried
out via the multi-master application controller.
After start-up, the PlanoSpot 360 DALI-2 S supply information regarding room occupancy and
motion detection as well as brightness values to the higher-level controller via the relevant
instances. The lighting and other systems in a building are controlled on the basis of this
information.
2.1 Overview of available instances
Instance
no.
Instance name
Instance
type
Standard
Memory bank
0
Occupancy sensor
Standard
detection zone
3
IEC 62386-303
2
1 Occupancy sensor Reduced
detection zone
3 IEC 62386-303 2
2
Light sensor, integral
4
IEC 62386-304
3
3
Light sensor, interior
4
IEC 62386-304
4
4
Light sensor, middle
4
IEC 62386-304
5
5
Light sensor, window
4
IEC 62386-304
6
6 / 7
Push button on / off
1
IEC 62386-301
7
8 / 9
Push button on / off
1
IEC 62386-301
8
10 / 11
Push button on / off
1
IEC 62386-301
9
12
Push button scene 1
1
IEC 62386-301
10
13
Push button scene 2
1
IEC 62386-301
11

PlanoSpot 360 DALI-2 S DE manual 5
3Technical data
Operating voltage
DALI (in accordance with IEC 62386-101): 10 V – 22.5 V
Power input
max. 10 mA
Connection type
Plug-in terminals
Cable cross-section
0.5 – 1.5 mm
2
Type of installation
1
Ceiling installation with springs
Size of flush-mounted housing
Size 1 (NIS, PMI)
Recommended installation
height
2.0 – 3.0 m / max. 3.5 m
Minimum height
> 1.7 m
Detection area, horizontal
360°
Detection area, walking
2
7.0 x 7.0 m | 49 m
2
Detection area, seated
3
4.5 x 4.5 m | 20 m
2
Light measurement
approx. 10 – 10,000 lux
Protection rating
IP 20
Ambient temperature
0 °C to +50 °C
CE Declaration of Conformity
This device corresponds to EN 60669-2-5.
RCM conformity
This device is compliant with the ACMA guidelines.
DALI conformity
IEC 62386-101/103/303/304
1Surface-mounted installation also possible with accessories
2Transverse movement with an installation height of 3 m, standard detection zone
3Seated with an installation height of 3 m, standard detection zone

PlanoSpot 360 DALI-2 S DE manual 6
4Product characteristics
4.1 Usage
The focus is on purpose-built facilities, within the following applications in particular:
•Offices
•Large offices
•School rooms
•Conference rooms
•Corridors
4.2 Functionality
•The PlanoSpot 360 DALI-2 S provides information about presence and brightness in
the form of a DALI telegram in line with IEC 62386 Part 303/304.
•3 mixed light measurements
•Easy to calibrate brightness measurement
•Square detection area for accurate and easy planning
•Optics can be tilted to adjust the detection area
•Test mode for checking function and detection area
•Configurable detection sensitivity
•Can be configured via DALI bus or remote control
•The theSenda S or theSenda B user remote controls can be used to dim or switch
the lamps, to control the blinds, or to execute additional functions via the higher-
level control.
•Flat design with interchangeable bezel frame in different colours
•Ceiling installation with springs
•Surface-mounted installation possible with 75B back box (optional)
•theSenda S user remote control (optional)
•theSenda B app remote control (optional) and corresponding theSenda Plug app
(for iOS/Android)
All of the product characteristics are described in detail in the following sections.

PlanoSpot 360 DALI-2 S DE manual 7
4.3 Dimensions
4.3.1 Ceiling installation with springs
4.3.2 Surface-mounted installation with 75B back box

PlanoSpot 360 DALI-2 S DE manual 8
4.4 Detection area
The square detection area of the PlanoSpot 360 DALI-2 S presence sensor guarantees accurate
and simple planning. There are 2 detection zones available.
Note that seated and walking persons are detected in differently sized areas.
The recommended installation height is 2–3 m.
As installation height increases, the sensitivity
of the PlanoSpot 360 DALI-2 S decreases. At an
installation height of 3 m or higher, walking
motions are necessary and the detection areas
of several PlanoSpot 360 DALI-2 S devices
should overlap in the marginal zones. The
detection range reduces as the temperature
increases, and the sensitivity can be adjusted in
5 increments via the DALI bus or with the
theSenda B/app remote control.
Seated persons
The PlanoSpot 360 DALI-2 S reacts very
sensitively to the slightest movements. The
details refer to very slight movements at table
height (approx. 0.8 m).
Walking persons
From an installation height of > 3 m, the size of
and distance between the active and passive
zones increase. More pronounced movements
are required for clear detection.
Standard detection zone
Installation
height (A)
Transverse (t)
Seated (s)
2.0 m
20 m
2
4.5 m x 4.5 m
9 m
2
3.0 m x 3.0 m
2.5 m
36 m
2
6.0 m x 6.0 m
16 m
2
4.0 m x 4.0 m
3.0 m
49 m
2
7.0 m x 7.0 m
20 m
2
4.5 m x 4.5 m
3.5 m
64 m
2
8.0 m x 8.0 m
–
–
Reduced detection zone
Installation
height (A)
Transverse (t)
Seated (s)
2.0 m
4 m
2
2.1 m x 2.1 m
4 m
2
2.0 m x 2.0 m
2.5 m
9 m
2
3.0 m x 3.0 m
6 m
2
2.5 m x 2.5 m
3.0 m
14 m
2
3.8 m x 3.8 m
9 m
2
3.0 m x 3.0 m
3.5 m
22 m
2
4.7 m x 4.7 m
–
–
Detection areas according to sensNORM, see data sheet
By tilting the optics manually, the detection area can be shifted towards the window or the
interior by 0.5 to 1 m, depending on the installation height.

PlanoSpot 360 DALI-2 S DE manual 9
4.5 Infrared receiver
An infrared receiver can be used to receive parameters and control commands. This process
involves unidirectional communication. The PlanoSpot 360 DALI-2 S can be operated with the
following remote controls:
−theSenda B/theSenda Plug remote control (9070985)
−theSenda S user remote control (9070911)
−theSenda P installation remote control (9070910) (limited functional support, see section
7.1 Settings via remote control)
4.6 Display/visualisation
The various statuses of the PlanoSpot 360 DALI-2 S are indicated via a red LED. The LED is
located under the lens. The following statuses are indicated in descending priority:
IR command accepted:
40 ms 2 s long
Flickering (12.5 Hz) when a valid remote control command is received.
IR command rejected:
400 ms
Rejection pulse when an invalid remote control command is received.
Error flashing:
160 ms continuous
Error flashing. Applies until the error has been resolved.
Identify device:
40 ms 10 s long
Identification of the sensor by means of the DALI command "IDENTIFY DEVICE"

PlanoSpot 360 DALI-2 S DE manual 10
No short address:
160 ms repeating every 2.36 s
No short addresses assigned to the sensor
Presence test:
LED lights up if motion is detected, otherwise switched off; applies until presence test is
completed.
Start-up phase:
1,280 ms 30 s long
Start-up flashing

PlanoSpot 360 DALI-2 S DE manual 11
5Connection
The PlanoSpot 360 DALI-2 S devices are connected to the DALI line.
An external DALI supply is required for operation of the PlanoSpot 360 DALI-2 S devices.
This DALI supply must be able to ensure a reliable power supply for all connected DALI
participants.
A minimum current of 10 mA per PlanoSpot 360 DALI-2 S must be provided.

PlanoSpot 360 DALI-2 S DE manual 12
6Installation
6.1 Ceiling installation
Installation in false ceilings for ceiling thicknesses of 0.5 mm to 3 cm. The drill diameter for the
ceiling cut-out is 68 mm. Remove the contact protection (a) and connect the DALI cable with
plug-in terminal (b). Implement cable strain relief with cable tie, put on contact protection (c).
Open springs and mount detector in ceiling (d). Pay attention to window / interior alignment (e).
Remove installation protection (f). Align the detection area as required, by tilting the optics by
12° to the right (I) or left (II) (g). Snap on the bezel frame provided (h).

PlanoSpot 360 DALI-2 S DE manual 13
7Operation
All settings are configured via the DALI bus or the remote control.
In its initial delivery condition, the PlanoSpot 360 DALI-2 S does not have a short
address.
7.1 Settings via remote control
The theSenda B/app and theSenda P remote controls can be used to set the following
parameters and control commands.
7.1.1 Parameters
Parameter
Description
Can be
queried via
app
Can be
changed
via app
Can be
changed via
theSenda P
Room correction
factor
Int/2
Integral room correction
factor, instance 2
Range 0.05 ../0.3/… 2.00
-
Brightness
measurement
value
Int/2
Lux meter brightness value
For calibrating the integral
brightness measurement,
instance 2
- -
Room correction
factor
Inn/3
Interior room correction
factor, instance 3
Range 0.05 ../0.3/… 2.00
-
Brightness
measurement
value
Inn/3
Lux meter brightness value
For calibrating the interior
brightness measurement,
instance 3
- -
Room correction
factor
Mid/4
Middle room correction
factor, instance 4
Range 0.05 ../0.3/… 2.00
-
Brightness
measurement
value
Mid/4
Lux meter brightness value
For calibrating the middle
brightness measurement,
instance 4
- -
Room correction
factor
Win/5
Window room correction
factor, instance 5
Range 0.05 ../0.3/… 2.00
-
Brightness
measurement
value
Win/5
Lux meter brightness value
For calibrating the window
brightness measurement,
instance 5
- -
Detection
sensitivity (PIR)
Increment 1 / 2 / 3/ 4 / 5
All instances

Detection zone
No function in mode 0x00.
-

-
Operating mode
Selection of DALI operating
mode 0x00 / 0x80 / 0x81
-
IR group
address A
IR group address button
instance 6–7
Range: I/II/III/ ../VIII/All
--

PlanoSpot 360 DALI-2 S DE manual 14
IR group
address B
IR group address button
instance 8–9
Range: I/II/III/ ../VIII/All
- -
IR group
address C
IR group address button
instance 10–11
Range: I/II/III/ ../VIII/All
- -
IR group
address D
IR group address button
instance 12
Range: I/II/III/ ../VIII/All
- -
IR group
address E
IR group address button
instance 13
Range: I/II/III/ ../VIII/All
- -
LED display –
no short
address
Selection of LED display if no
short address is assigned
"Permit flashing" /
"Suppress flashing"
- -
Bold indicates default values / factory settings
Room correction factor / brightness measurement value
The room correction factor is a measurement for the difference between brightness measure-
ments on the ceiling and the work area. The brightness value on the ceiling is influenced by the
installation location, the incidence of light, the position of the sun, the weather conditions, as
well as the reflection properties of the room and the furniture.
With the room correction factor, the measured brightness value is adjusted to the conditions in
the room and in this way can be matched to the lux meter value (1) measured at the surface
beneath the PlanoSpot 360 DALI-2 S.
~1.5 m ~1.5 m
Illustration of the light measurement at table height
(0.8 m)
with an installation height of 2.5 m
1.0 x 1.8 m 0.8 x 1.6 m 1.0 x 1.8 m
Interior Middle Window
Brightness value on the ceiling
Room correction factor = -----------------------------------------
Brightness value on the work surface

PlanoSpot 360 DALI-2 S DE manual 15
We recommend the following procedure:
Place the lux meter or theSenda B remote control with integrated lux meter on the work
surface under the PlanoSpot 360 DALI-2 S, enter the measured lux value via theSenda
B/app remote control (parameters <Brightness measurement value Int/2, Inn/3, Mid/4,
Win/5>) and send to the PlanoSpot 360 DALI-2 S.
During lux measurements, observe the relevant distances (see illustration above).
Carry out all measurements at table height.
-<Brightness measurement value Int/2>: Average of all 3 lux measurements Inn/3,
Mid/4, Win/5.
-<Brightness measurement value Inn/3>: Lux measurement towards the interior
-<Brightness measurement value Mid/4>: Lux measurement in the middle (below
PlanoSpot 360 DALI-2 S)
-<Brightness measurement value Win/5>: Lux measurement towards the window
→The room correction factor is calculated from this automatically. Values between 0.05 and
2.0 are permitted. Calculated or entered values outside the permitted range are
automatically set to the appropriate limit value.
→The calculated room correction factor is adopted. The room correction factor can be
checked via the <Room correction factor Int/2, Inn/3, Mid/4, Win/5> parameter for
monitoring purposes.
The standard value is 0.3 and is suitable for most applications. Changes are only sensible
in strongly deviating situations.
Detection sensitivity
The PlanoSpot 360 DALI-2 S has 5 sensitivity increments. The basic setting is the middle
increment (3).
Increments 1 to 5 can be selected and sent to the PlanoSpot 360 DALI-2 S with the theSenda
B/app remote control.
On the theSenda P installation remote control, the sensitivity can be decreased by one
increment each time the button is pushed or increased with the button.
Value range
Increment
Sensitivity
1
Very insensitive
2
Insensitive
3
Standard
4
Sensitive
5
Very sensitive
Detection zone
It is possible to choose between the "standard" and "reduced" detection zones. This setting is
only possible in operating mode 0x80 or 0x81, see separate manual. In operating mode 0x00,
the PlanoSpot 360 DALI-2 S rejects this command.

PlanoSpot 360 DALI-2 S DE manual 16
Operating mode
In its factory settings, the PlanoSpot 360 DALI-2 S is set to DALI-2 standard (operating mode
0x00).
The proprietary DALI mode 0x80 or 0x81 was used for older systems. If the PlanoSpot 360
DALI-2 S is to be integrated into such a system, the relevant operating mode – 0x80 or 0x81 –
can be selected. There is a separate manual for operating modes 0x80 and 0x81.
IR group address
The button instances of the PlanoSpot 360 DALI-2 S and the buttons on the user remote
controls are linked with each other via an IR group address. This means that adjacent PlanoSpot
360 DALI-2 S devices can be separated from each other.
The button instances of the PlanoSpot 360 DALI-2 S are only actuated if the IR group address of
the button instance matches that of the user remote control.
Users can choose from I, II, III, IV, V, VI, VII, VIII and All for the IR group addresses. In the case of
the PlanoSpot 360 DALI-2 S presence sensor, the "IR group address" parameters are assigned
to the following button instances:
•IR group address A Button instance 6 and 7
•IR group address B Button instance 8 and 9
•IR group address C Button instance 10 and 11
•IR group address D: Button instance 12
•IR group address E: Button instance 13
Further information can be found in section 9.8 Button function.
LED display – no short address
If a PlanoSpot 360 DALI-2 S has not yet received a short address, this can be indicated via the
red LED. In order for this to happen, the parameter must be set to "Permit flashing", otherwise
it should be set to "Suppress flashing".
7.1.2 Control commands
Control command
Description
Can be
triggered
via
app
Can be
triggered via
theSenda P
Quiescent mode
On/Off

-
Presence test
On/Off


Restart
Restart sensor


DALI reset
Set DALI reset values

-
DALI default
Set DALI default values

-
Factory settings
(factory reset)
Reset device to factory settings.
-
Quiescent mode
If quiescent mode is activated, the PlanoSpot 360 DALI-2 S will not send any event telegrams to
the DALI bus. Quiescent mode has a time limit of 15 minutes.

PlanoSpot 360 DALI-2 S DE manual 17
Presence test mode
Presence test mode is used to test presence detection. Presence test mode can be activated
with the theSenda B/app or with the theSenda P installation remote control ( button). When
the test mode is set, the PlanoSpot 360 DALI-2 S switches directly to test mode:
•Every movement is indicated by the LED. The hold timer is temporarily set to 10 s and the
dead timer is set to 0 s. The PlanoSpot 360 DALI-2 S sends event telegrams to the DALI bus
in line with the configuration of the presence sensor.
•To ensure that the light is switched on regardless of the brightness, the PlanoSpot 360
DALI-2 S sends the lowest brightness value (0).
•Test mode ends automatically after 10 min. The hold timer and dead timer return to the
values set before the test.
Restart
The restart can be initiated with the theSenda B/app or the theSenda P remote control (
button). The subsequent start-up phase takes around 30 seconds. This phase is indicated by the
LED, start-up phase flashing pattern, see section 4.6 Display.
DALI reset
All DALI variables are set to the reset values in accordance with IEC 62386-103/303/304.
DALI default
All DALI variables are set to the default values in accordance with IEC 62386-103/303/304.
Please note: This also means that the short address will be reset.
Factory settings
This control command resets all parameters of the PlanoSpot 360 DALI-2 S to the factory
settings and sets all DALI variables incl. memory bank entries to the default values in
accordance with IEC 62386-103/303/304.
Please note: This also means that the short address will be reset.
The PlanoSpot 360 DALI-2 S presence sensor is supplied with the following parameter values:
Parameter
Value
Room correction factor Int/2
0.3
Room correction factor Inn/3
0.3
Room correction factor Mid/4
0.3
Room correction factor Win/5
0.3
Detection sensitivity (PIR)
3
Detection zone
Standard
Operating mode
0x00
IR group address A
I
IR group address B
II
IR group address C
III
IR group address D
All
IR group address E
All
LED display – no short address Flashing permitted

PlanoSpot 360 DALI-2 S DE manual 18
7.2 Settings via the DALI bus
All of the parameters* and control commands described above can also be set by the multi-
master application controller via the DALI bus. They are stored in the memory bank.
* Exceptions: "Brightness measurement value Int/2, Inn/3, Mid/4, Win/5" and "LED display – no short
address" parameters. These parameters cannot be transferred via the DALI bus (see table in section 7.1.1).
7.3 Status messages via the DALI bus
The "QUERY INPUT DEVICE ERROR" command can be used to query the error status of the
PlanoSpot 360 DALI-2 S (no response means no error):
Bit
Name
Value
Measures
0
Checksum_Error_Info 1 = Yes Return the PlanoSpot 360 DALI-2 S for repair
1
Reserve 1 = Yes
2
Checksum_Error_Parameter 1 = Yes Reset to factory settings
3
Kein_HTS_Code 1 = Yes Return the PlanoSpot 360 DALI-2 S for repair
4
EEPROM_Error 1 = Yes Return the PlanoSpot 360 DALI-2 S for repair
5
Checksum_Error_DALI 1 = Yes Reset to DALI default values
6
Reserve 1 = Yes
7
instanceError 1 = Yes Further queries are required, see below
In the event of instanceError, the "QUERY INSTANCE ERROR" command must be executed for
the "Occupancy sensor", "Light sensor" and "Button instance" instances:
-If the "Occupancy sensor" instance returns an error notification: Return the PlanoSpot 360
DALI-2 S for repair.
-If the "Light sensor" instance returns an error notification: Return the PlanoSpot 360 DALI-2
S for repair.
-If the button instance returns an error notification: Check the remote control, push buttons.

PlanoSpot 360 DALI-2 S DE manual 19
8Light measurement
8.1 Light measurement
The mixed light measurement measures artificial light and daylight. It provides consistent
measurement results regardless of the light source. The artificial light from fluorescent lamps
and LEDs is detected correctly despite the discrete spectrum. The light measurement device is
located under the lens and receives diffuse light as a result.
The PlanoSpot 360 DALI-2 S has 3 light measurements:
The light guide is designed in such a way that the light measurement covers an opening angle
of approx. ± 40° below the PlanoSpot 360 DALI-2 S and to the side.
The central light measurement detects the brightness directly below the "Middle brightness
value" detector (A), while the other two light measurements detect the brightness close to the
window ("Window brightness value"; B) or in the interior ("Interior brightness value"; C). The
installation location is the reference point for the lighting level.
The measured brightness value can be adapted to the conditions in a room with the room
correction factor. The brightness measurement transmitted for instance 2 to 5 is thus the
measured brightness value / room correction factor.
See also the description of the room correction factor on page 14.
The measurement range of the light measurement is around 10 to 10,000 lux.

PlanoSpot 360 DALI-2 S DE manual 20
8.2 Determining a value via the DALI bus
According to DALI standard IEC 62386-103/304, the value of a light sensor instance is obtained
either by querying directly or by evaluating the events.
8.2.1 Direct queries
The following steps must be carried out in order to query the value directly:
1. Address the DALI telegram "QUERY INPUT VALUE" to the desired device and with the
desired instance number of a light sensor.
2. Multiply the returned value by 64 and save in a variable of at least 16 bits.
3. Address the DALI telegram "QUERY INPUT VALUE LATCH" to the previous device with the
previous instance number.
4. Divide the returned value by 4 and add to the previous variables.
Example as pseudo code:
inputValue = QUERY_INPUT_VALUE()
Variable = inputValue × 64
inputValue = QUERY_INPUT_VALUE_LATCH ()
Variable = Variable + inputValue ÷ 4
8.2.2 Evaluating events
A light sensor instance event can be triggered cyclically or in the case of certain changes to the
value. The following steps are necessary in order to present the value that has been received in
lux:
1. Extract the 10-bit event information from the 24-bit light sensor event telegram that has
been received and save it in a variable of at least 16 bits.
2. The variable must then be multiplied by 16 in order to present the value in lux.
Example as pseudo code:
inputValue = EVENT_INFO
Variable = inputValue × 16
As the event information is limited to 10 bits, only increments of 16 lux are possible. If a
more precise value is required, this can be queried directly in full resolution. See 8.2.1
Direct queries